Conductivity
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Sensor String System Flexible Subsea Observatories
SeaGuard Sensor String
-
The Aanderaa SEAGUARD® Sensor String Systems are complete and flexible subsea observatories for measurements of e.g. dissolved oxygen, conductivity, temperature, current, pressure and tide.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Transformer Test Panel/ Setup
-
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
Product
Salt Contamination Meter
130
-
Key features of the Elcometer 130 Salt Contamination Meter include: Fast reading rate allows multiple conductivity tests to be completed efficiently Pressure plate ensures a constant and uniform pressure to paper Automatic detection of paper size and automatic adjustment of reading value USB and Bluetooth® data output to ElcoMaster® software Dust and water resistant rugged design equivalent to IP64 Automatic temperature compensation ensures accurate results Non-oxidising gold plated contacts ensures lifetime accuracy Stores up to 150,000 readings in 2,500 alpha numeric batches Fully portable hand-held, ergonomic design ideal for use in the field
-
Product
VPX/open VPX C-Frame 5 Slot 6U
-
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
Product
Gas Measurement Device
Gascoseeker 2-500
-
Teledyne Gas & Flame Detection
Built on the success of the robust and reliable Gascoseeker MK2, the Gascoseeker 2-500 is the UK gas industry standard instrument for measuring % LEL and % volume flammable hydrocarbons, with over 20,000 instruments in use in the UK gas industry.The two-button operation means the Gascoseeker 2-500 is easy to use and operator training can be conducted quickly. The rugged design allows the Gascoseeker 2-500 to be used in harsh environments. The Gascoseeker 2-500 is also fully compatible with our range of calibration software and equipment.
-
Product
Software Compatibility Testing Services
-
ImpactQA uses compatibility testing to ensure interoperability between your business-critical systems to discover important modifications or additions required. Following functional necessities, we offer solutions so that our clients could avoid loss of reputation and financial risks caused by poor system compatibility. Testing conducted before the product releases identify compatibility glitches and controls project budget over the prescribed limits. ImpactQA offers an end to end compatibility testing services and infrastructure to make sure your apps deliver for your users and your business.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
SparkFun Soil Moisture Sensor (with Screw Terminals)
-
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
Product
Incline Impact Tester
KRD100 series
-
KRD100 series incline impact tester simulates the ability of product packaging to resist shock damage in the actual environment, such as handling, stacking of shelves, sliding of motors, loading and unloading of locomotives, product transportation, etc. This machine can also be used as a common test equipment for scientific research institutions, colleges and universities, packaging technology test centers, packaging materials manufacturing plants, and foreign trade, transportation and other departments to conduct incline impact test.
-
Product
Multi-Parameter Profiler
fastCTDplus Fluorescein
-
A conductivity cell designed for optimum flow-through, a fast-response thermistor temperature sensor and 0.01% pressure sensor together with a Fluorescein sensor, all synchronously sampling at up to 32Hz to deliver the highest quality profiles in a lightweight and robust package.
-
Product
3-Axis AGREE Chamber Vibration Test Chamber Elevator Mechanism
-
Guangdong Test EQ Equipment co., Ltd.
Widely used in aviation, aerospace, shipbuilding, defense, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries. Designed to assess the reliability of electrical/electronic products, instruments, and equipment during transportation, storage, and operation. This integrated system combines a temperature/humidity test chamber with vibration platforms to independently conduct temperature, humidity, vibration, and combined environmental tests.
-
Product
Liquid Thermal Shock Baths
TSB Series
-
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
Product
PXI 3A Power MUX BRIC, 16-Channel, 12-Pole
40-571-304
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Universal Tensile Testing Machines
-
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
Product
Thermal properties sensor
TP01
-
Hukseflux Thermal Sensors B.V.
TP01 is designed for long term (permanent) installation in soils. It covers the thermal conductivity (λ) range of 0.3 to 4 W/m.K, which is sufficient for most inorganic soil types. The core of TP01 is a differential temperature sensor (2 thermopiles) (1) measuring the radial differential temperature with record breaking sensitivity. The sensor performs a temperature measurement around a heating wire (2).
-
Product
Explosion-Proof Gas Analyzer
51 Series
-
HORIBA’s 51 Series of explosion-proof analyzers provide safe, reliable and accurate measurements when analyzing flammable gases or operating in explosive environments. The 51 Series complies with IEC 60079. The 51 Series explosion-proof analyzers infrared allow for the measurement of CO, CO2, CH4 and other organic gases. The TCA-51 uses a thermal conductivity detector for H2 measurements and the MPA-51 and PMA-51 models integrate magneto-pneumatic and paramagnetic detectors for O2 measurements.
-
Product
700 W VITA62 PSU | conduction cooled | 6 U | 5 HP | DC
MS216479+RC
-
Designed to meet the requirements of VITA 62 for use in harsh environments. For use in DC systems, they are 6 U high by 5 HP (1-inch) wide modules with guide blocks, for use in conduction cooled VPX systems.
-
Product
4-Wire Universal Cable Tester
LX-860
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
Explosive Atmosphere Test
-
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
Product
Software Packages
GLUON
-
The software uses notched specimens (CT specimens) to evaluate the material elasto-plastic fracture toughness value (JIC). The test is conducted at constant loading rate under test-force control or CTOD control and the load is removed to calculate the crack length. The software plots graphs of the crack length increase (Δa) and crack growth resistance (J value) from the acquired data, calculates the JIC value, and evaluates its validity.
-
Product
12-Channel ADC Module
FMC112
-
Sundance Multiprocessor Technology Ltd.
The FMC112 is a twelve-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC112 provides twelve A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC112 has the LPC (Low-Pin Count) connector, front panel I/O, and is conduction cooled capable.
-
Product
Process Automation
-
At GF Industry and Infrastructure Flow Solutions, we provide comprehensive solutions for your processes, focusing strongly on manual and actuated valve, and measurement solutions such as flow, pH/ORP, conductivity, temperature, pressure, level, dissolved oxygen (DO), free chlorine as well as monitors, transmitters and controllers for the safe management of your liquid processess.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Universal Converter
C8000
-
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
Product
Superconducting Switches
-
switches back and forth between superconducting and normally conducting state.
-
Product
Windshield Temperature Controllers
Controller
Window Temperature Control is a necessary component of any aircraft and Astronics has decades of design experience meeting customer requirements, including high power DC for heating transparent conductive gold film. Astronics units supply heating power to the windshield, monitor the windshield temperature, and provide control function to the cockpit.
