Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
Power Supply
44216
-
This extremely efficient power supply converts 100~240 AC volts into 17 amps of continuous 13.8 volt DC power, making it compatible with a wide variety of DC chargers.
-
Product
Temperature Transmitter
T4111
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
Product
Current Shunt Module
CURS100
-
The CURS100 converts a current signal output by a sensor or output device (e.g., 4 to 20 mA) to a voltage that can be measured by a datalogger. The 100 ohm resistor used for the current shunt allows currents up to 25 mA to be read on a 2500 mV range (CR10, CR10X, CR510, CR500) and currents up to 50 mA to be read on a 5000 mV range (CR23X, 21X, CR7, CR5000, CR9000, CR9000X).
-
Product
2-28 Vrms Input, 2-115 Vrms Exc, 47 Hz - 1 kHz Freq
SDx
-
Synchros and Resolvers are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Resolver-to-Digital or a Synchro-to-Digital converter is used to convert these signals to a digital output corresponding to the shaft angle and/or velocity.
-
Product
Multifunction Reconfigurable I/O Device
Multifunction Reconfigurable I/O
Multifunction Reconfigurable I/O Devices feature a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control.
-
Product
AC/DC Converters
-
Start-Power manufactures single and three-phase unidirectional analogue AC-DC Converters and single and two-directional three-phase digital AC-DC Converters. One- and three-phase unidirectional analogue AC/DC Converters can be used as motor controls or as power supplies in sizes from 40A up to 500A. Three-phase uni- and bidirectional digital AC/DC converters are suitable for speed and torque control of motors.
-
Product
Transceivers
-
Schweitzer Engineering Laboratories, Inc.
Transceivers convert between copper and fiber optics or between other communications interface standards.
-
Product
PCI Data Acquisition Boards
DA14-100DMA Series - Dual 14-bit D/A, 15 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
600-Watt DC/DC Converter, 6U VME
64PS1
DC Converter
The 64PS1 is a 600 Watt DC/DC Converter that plugs into a 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +28 VDC input and provides a single output at 600 Watts continuous or 1,000 Watts peak.
-
Product
File Import Tool For Importing And Converting STIL, WGL, VCD/EVCD Vectors
DIOEasy-FIT
-
Marvin Test Solutions' DIOEasy-FIT option offers test engineers a software tool set for importing and converting STIL, WGL, VDC/EVCD files to a Marvin Test Solutions' digital instrument file format. DIOEasy-FIT works in conjunction with Marvin Test Solutions' DIOEasy waveform display and editor software which provides an efficient tool set for developing, debugging, and executing digital test vectors for all MTS dynamic digital instruments.
-
Product
500 Watt DC/DC Converter, 3U VPX
VPX55H-3
DC Converter
The VPX55H-3 is NAI's latest high power 500 Watt DC/DC converter that accepts a +28 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 0.8” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Managed Hardened Media Converter, 1000Mbps, 2xSFP, AC Adapter (Also Known As IE-Multiway 858-11121; Previously BB-858-11121)
IMC-574I-SFP-PS
-
Versatile 4-port media converterSupports SNMP for managementSupports a variety of SFP modulesWorks under an extended temperature rangeSupports OAM, VLAN, 1+1 revertiveProvides RS-232 CLI (command line interface) console port
-
Product
Electrical Probe Systems
-
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Analog Power Modules
-
Renesas' family of analog power modules offers users a fully integrated DC/DC switching buck converter in one package. These modules combine the controller, power FETs, output inductor, and compensation circuitry in a single package minimizing both the external component count and complexity of converter design.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Hardened Media Converter, 100Mbps, Multimode 1310nm, 2km, SC
EKI-2541MI
-
Provides 1 x 10/100 Mbps Ethernet port with RJ45 connectorProvides 1 x 100 Mbps multi-mode SC type fiber portProvides internal jumper for Link Fault Pass-through (LFP) settingSupports full/half duplex flow controlSupports store and forward transmissionSupports auto-negotiationSupports MDI/MDI-X auto crossoverSupports redundant 12-48 VDC power inputProvides flexible mounting: DIN-rail and Panel mountSupports wide operating temperatures from -40 to 75°C
-
Product
Motion Magnification Software
Dragon Vision
-
Incredible as it may seem, machine and structural vibration (or at least a large part of it) can be detected in a video recording with incredible resolution. Our unique video analysis algorithms make it possible to detect micro-movements and convert these movements into thousands of reliable vibration signals from just one video. In addition, with our software it is possible to perform motion magnification, making it possible to visualize vibration in ways that the human eye can’t see.
-
Product
Detector
-
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
Product
Power Quality Software
-
Save Time and Improve Accuracy When Troubleshooting AnswerModules® are proprietary algorithms that convert raw power quality event data into precise answers to determine the source and cause of the disturbance. Read More
-
Product
Digital MultiMeter
12061
-
Chroma Systems Solutions, Inc.
The 12061 6½ Digital Multimeter has assorted settings for resolution, integration time and ranges that allow users to optimize the configuration of measurement speed, resolution and accuracy when in individual measurement test modes. The 12061 has built-in a high speed, low interference A/D converter with a maximum speed of 2000 rdgs/s, making it the best solution for high speed measurement.
-
Product
PXIe 8 Bit High Speed Digitizer 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4X.2234-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-4463, 51.2 kS/s, 2-Output PXI Sound and Vibration Module
783086-02
Sound and Vibration
51.2 kS/s, 2-Output PXI Sound and Vibration Module - The PXIe‑4463 offers high dynamic range and THD+N for audio, acoustic, and vibration applications. It provides the high precision and dynamic range necessary for the most stringent audio generation requirements in a modular form factor. The PXIe‑4463 contains two 24-bit digital‑to‑analog converters to allow for fully differential simultaneous generation. Complete with three gain ranges, the PXIe‑4463 can generate current with programmable, per channel output configurations. The two timing engines allow you to perform multisample-rate applications on a single module and independently start and stop channels on a single module.
-
Product
Current To Pressure Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Current to Pressure Trainer. This setup comprises of a I to P converter fitted on a base. Two pressure gauges are fitted one at the input side and the other at the output of the I to P converter. A current source with digital display is provided to excite the I to P converter. A constant air supply should be provided to the system at 20 PsI Pressure from a standard compressor.
-
Product
Quad 12 Gsps 16-bit DAC& Quad 4 Gsps 12-bit ADC
ADF-QMx44
-
The DEG ADF-QMx44 FMC leverages the Analog Devices AD9081 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a quad 12-bit, 4 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx44 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and four receiver channels.
-
Product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - PCIe
Model 78670
-
Model 78670 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. This 4-channel, high-speed data converter is suitable for connection to transmit HF or IF ports of a communications or radar system. Its built-in data playback features offer an ideal turnkey solution for demandingtransmit applications.
-
Product
Gamma Spectrometer
-
A gamma spectrometer is a specialized instrument used to detect and measure the energy of gamma rays. It works by converting the high-energy gamma rays into electronic pulses, which are then analyzed to determine the energy distribution of the gamma radiation.
-
Product
I/P Electro-Pneumatic Signal Converters
TEIP11 / TEIP11-PS
-
Electro-pneumatic signal converters are the link between the control rooms and pneumatic actuators. I/P converters are available with and without booster stage.
-
Product
Timing Board #1
TIO-10 #1
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
