Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
DALI 0-10v Converter
-
The DALI 0-10V Converter converts DALI signal to the Analog 0-10V protocol.
-
Product
Handheld Performance Tuner
Max Energy
-
Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire rpm band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter un-locking and transmission down-shifting to a lower gear. The results are maximum power and fuel mileage.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Frequency Down Converters
-
In digital signal processing, a digital down-converter (DDC) converts a digitized, band-limited signal to a lower frequency signal at a lower sampling rate in order to simplify the subsequent radio stages.
-
Product
Lamp Converters
-
PeakTech Prüf- und Messtechnik GmbH
This AC / AC voltage converter is particularly suitable for use with halogen indoor lights and other low-voltage light sources that require an AC voltage source for supply. There is a safe galvanic separation between mains and low voltage according to the isolating transformer standard. This pre-assembled AC / AC converter is equipped with an overtemperature switch that cannot be reset.
-
Product
Angular Orientation Sensor
WOS-120
-
The Miniature Angular Orientation Sensor system Model WOS-120 contains both a 3-axis fluxgate magnetometer and a 3-axis accelerometer. These sensors are sampled by an internal A to D converter and microprocessor subsystem which outputs 16 bit digital data representing the magnetometer and accelerometer readings. The system can also be configured to transmit the roll, pitch and azimuth orientation angles of the Model WOS-120 system. These angles are calculated before transmission from the accelerometer and magnetometer sensor output data.
-
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4I.4480-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Embedded LO Capability
S95084B
-
The S95084B software tunes the analyzer’s receivers to the output frequency of the converter under test without the need for access to internal LOs or a common reference signal.
-
Product
Current to Digital
-
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
Product
ARINC 818 to DVI Converter
-
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
Transition Time Converter, 250ps
15432B
Transition Time Converter
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
Web Sensor Hygrometer
T3511-4
-
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Dual MAX31865 PT-1000 RTD to Digital Breakout
SEN-30202-PT1K
-
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information.
-
Product
DC/DC With UPS And Charge Controller
PCM-PS402-512
DC Converter
WINSYSTEMS’ PCM-PS402-512 is a wide input range, triple output PC104 DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40° to +85°C without a fan or heatsink making it ideal for industrial applications.
-
Product
Integrated Frequency to Voltage Converter
FV
-
The FV6 Frequency to Voltage Module provides a convenient method of converting up to six frequency signals to analog voltages that can be fed into common data acquisition equipment.
-
Product
IRD
SFT358x
-
Hangzhou Softel Optic Co., Ltd.
SFT358X IRD is a new design which integrates demodulation (DVB-C, S/S2 optional), de-scrambler and multiplexing in one case to convert RF signals into TS output.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
Digital / Synchro Converter
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Encoders
-
Panasonic Industrial Devices Sales Company of America
Panasonic Encoders convert the manual rotary operation of an actuator or knob into coded signal outputs. The operation is similar to Potentiometers but the output signal is different in that it is a repeated pulse signal rather than a continuous analog signal. Panasonic Encoders offer options such as high torque, push lock, long life, push-on switch, water proof and center space.
-
Product
ULI-211CI -Triple Isolated RS-232/422/485 (Terminal Block) To Multi-Mode Fiber Converter (ST Connectors) DIN Rail Mounted
BB-FOSTCDRI
Terminal Block
Converts serial data signals to multi-mode ST fiber optic2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2
-
Product
Mini Hardened Media Converter, 100Mbps, Single-Strand 1550xmt, LFPT, 20km, SC
IMC-350I-SSR
-
Centralized powered IMC-318I chassisSupports Link Fault Pass Through functionality (LFPT)IEEE802.3af compliant (IMC-350I series as PoE-PD)Industrial grade design that supports an extended operating temperature(IMC-350I series)Metal enclosure with compact size
-
Product
128 Channel Multihit TDC
VX1190A-2eSST
-
The VX1190A-2eSST is a 128 channel Multihit TDC, housed in a 1-unit wide VME64X 6U module. The unit features High Performance Time to Digital Converter chips developed by CERN. LSB can be set at 100 ps (19 bit resolution, 52 µs FSR), 200 ps (19 bit, 104 µs FSR) or 800 ps (17 bit, 104 µs FSR).
-
Product
6 Channel ADC FMC Module
ADCFN06 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN06 is a six channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-25MHz sampling speed based on ADI AD9650. A DC coupled input is supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
Industrial Automation
-
PLANET Industrial Automation solution is designed to help set up IP networking in the areas of Industrial 4.0 and IoT using the serial port connection. Our Industrial Automation product line includes RS232/RS422/RS485 Serial Device Servers, Modbus Gateways, EtherCAT Slave I/O Modules and Serial over Cellular Gateways, each of which enables to convert and transform useful data for further analysis to optimize factory operation and management.
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
-
Product
HOTLink module (SAM)
ARINC 818
-
The HOTLinkTM stand alone module (SAM) is an invaluable tool for HOTLink testing. The SAM can be used as a portable signal converter, splitter, test pattern generator, or continuity tester. The SAM comes standard with an A/C adaptor and is also compatible with A/C 28 VDC.
-
Product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
Digital / Synchro Converter
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
