Drives
-
Product
Power Analyzers
-
Real drive and test bench applicationMultiple power analyzer in one instrumentUltra flexible channel configurationWide range of fundamental frequencyCAN interface for automotive and test bench linkInternal current transducer supply and TEDS support
-
Product
PPC8315 Processor AMC W/ 2.5” SATA Drive
AMC715
-
The AMC715 is a Processor AMC (PrAMC) with an on board 2.5" SATA hard disk drive in a single-module, mid-size AdvancedMCTM (AMC) form factor based on the AMC.1, AMC.2 and the AMC.3 specifications. The module is ideal to be used for data flow management within a chassis. The AMC715 provides a low cost solution with an integrated high capacity disk. With a storage capacity of over 320 GB and data transfer rates of 150 Mbyte/s the AMC715 is the ideal AdvancedMCTM smart storage. The PCIe interface is configurable as Host or Agent mode. The module has 512 MB of DDR2 memory on board.
-
Product
Radar Test System
UTP 5065
-
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
Non-contact Measurement Wafer Sorting System (Belt Drive Tranceportation)
NC-6800
-
*Non-contact measurement of resistivity, thickness and conductivity (P/N)*Number of cassette station can be changed by customers request*Eddy current method for resistivity, Electric capacitance method for wafer thickness*Temperature correction for silicon wafer function
-
Product
PRECISION MAGNETICS ANALYZER
3260B SERIES
-
At the design stage of component development it is vitally important to understand how the component performs under different operating conditions. This might include operation at diverse frequencies, AC drive levels or DC bias currents.
-
Product
96 Sink/Source
YAV90096
-
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Product
Battery Simulator SoftPanel
A170202
-
For the products developed to connect batteries for use, if the battery is not ready or unable to be provided due to high cost, the 17020 battery simulator can be used to confirming the product functions during development. The applications of battery simulator include motor drives within the car system, OBC, D-D convertor or charger within the CSS system and products of DC bus, etc.
-
Product
SATA Solid State Drive (SSD) Modules; 1TB TLC
FM8
-
SATA Solid State Drive (SSD) Modules (FM8) is a plug-in SATA drive compatible for use with NAI single board computers and multifunction I/O boards where a direct SATA interface to a processor is supported. The FM8 module has a capacity of 1TB in a triple-level cell (TLC) construct.
-
Product
SpikeSafe DC / Continuous Pulsed Current Sources
-
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
Product
GPIB Relay Interfaces
-
*ICS's GPIB to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the GPIB to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any GPIB programming language. Use ICS's interactive GPIB Keyboard program for easy operation from your PC without having to write a program.
-
Product
PXI Semi-Dynamic Digital I/O Module, 32-Channel
40-419-003
-
The 40-419-003 is a 32-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
1x4 Switch
S-104
-
1 X 4 Switch slot module of FOTS system carries out the switching function that enables a single channel input to go to any of 4 outputs or a selected particular channel of 4 inputs to go to a single channel output. And its MEMS type switch module is bidirectional and transparent to signal format. It is remarkable that high speed switching and various driving program such as timed, manual or sequential switching mode are available through the combination of high speed response time switch and high speed FPGA processor. On the basis of less than 1ms switching time and 10ms minimum switching, high speed sequential switching can be installed easily by defining switching order, interval time and duration. Current switching channel status can be checked through LED fronted with slot, and present driving condition of optical switch can also be monitored through GOI or LCD monitor.
-
Product
Proximity
-
Proximity detection sensors measure reflected infrared (IR) energy to detect the presence of an object or person. The devices include an integrated LED driver and, in some devices, an integrated LED. The proximity detection devices provide four programmable LED drive currents and IR pulse repetitions. The proximity detection circuitry compensates for ambient light, allowing it to operate in environments ranging from bright sunlight to dark rooms. The wide dynamic range allows operation in short-distance detection applications behind dark glass, such as mobile phones. Proximity detection sensors can be used to replace a mechanical switch or to sense human gestures.
-
Product
Semiconductor Memory Tester
T5851
-
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
Product
Intel® 6th/7th Generation Core™ I3/i5/i7 Performance Embedded PC
EPC-B2205
-
Supports Intel® 7th & 6th Gen Core™ i processor (LGA1151) with Intel Q170/H110 chipset.Two 260-pin SO-DIMM up to 32GB DDR4 2133 MHz SDRAM.Supports triple display of VGA/DP/DVI.One expansion slot (low profile).Two Shock Resistant 2.5" drive bays.Support SUSI, WISE-DeviceOn and Edge AI Suite.
-
Product
IGBT Drive
-
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
Product
32-Ch Isolated Digital Output PCI Card
PCI-1734
-
ISA-Compatible with PCL-73432-ch Isolated digital outputHigh output driving capacityD-type connector for isolated output channelsHigh-voltage isolation on output channels
-
Product
Industrial Clamp Meters
-
*Measures AC+DC current*AC and AC+DC voltage measurements with digital low pass filter for accurate readings on variable frequency drives*Also measures DC voltage, resistance, capacitance and frequency*Tests continuity and diodes*Flashlight inside clamp jaw for easier work in dark locations*Backlight & relative mode for added versatility*Peak-RMS measures motor inrush current*AmpTip™ increases accuracy on small wires and low current*Two voltage detection modes - non-contact or using a single test lead*Data hold*Recording of Maximum, Minimum, and Average readings*Crest (peak hold) feature captures current or voltage peaks as short as 5 milliseconds
-
Product
Desktop/Wallmount Chassis
IPC-7120
-
Desktop/Wallmount Chassis with front I/O Interfaces for ATX/mATX Motherboard. With front I/O interface and four to seven expansion slots. Shockproof drive bay for one 5.25" ODD and two 3.5" HDDs. LED indicators for power status and HDD activity, Support four to seven half-size add-on cards.
-
Product
Gearbox Tester
-
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Microwave Testing
10
-
PICOPROBE® MODEL 10 is a multipurpose, high speed, passive probe which can be used for driving as well as receiving signals. The Model 10 consists of a one meter length of flexible 50 ohm coaxial cable terminated by a carefully trimmed SMA on one end and by a miniature, high speed 50 ohm connector, specially developed to receive Model 10 replaceable coaxial probe tips, on the other. The 50 ohm coaxial cable was custom designed for Model 10 to be high speed, yet very flexible, so that moving the cable would not disturb the probe points.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Econo Motion Controllers
DMC-41x3
-
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
Product
1U Rackmount Chassis For Full-size SBC
AX61120TB
-
The AX61120TB is a slim 1U-high rackmount industrial computer chassis. This chassis supports up to two PCI expansion slots and can be equipped with a 250W ATX PFC power supply. The front access I/O ports are designed for ease access. The efficient cooling system keeps the system away from over heated. This industrial chassis features two internal 3.5" drive bays and a slim-line CD-ROM disk bay for ease of system installation. Furthermore, the AX61120TB can accommodate various full-size PICMG single board computers.
-
Product
Data Center
-
InnoLight Technology Corporation
New applications such as digital reality, artificial intelligence, machine learning are driving the network traffic to an unprecedented level. Cloud operators need continuing innovation in optical solutions to support bandwidth demand. InnoLight's comprehensive family of optical transceivers, including 10G, 25G, 40G, 100G, 200G, 400G and 800G will enable cloud operators to rapidly upgrade its network.
-
Product
2U Chassis
-
2U chassis supports comes in 2U 12 Bays to 2U 24 Bays with multiple configurations including AOI and SATA hard drive which can apply for various types of server systems.
-
Product
Servo
-
The Hardware: Drives, Motors, Cables (standard and robotics) – all seamlessly supported by Unitronics’ PLCs, HMIs, & VFDsThe Software:One integrated software for your complete motion application: PLC, HMI, Servo, VFD, and I/O
-
Product
LVDT I/O Cards
CPE4000
-
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
Product
700 - 3200MHz 100W Amplifier
VBA3200-100
-
High reliability proven GaAs design. Class A for maximum mismatch drive. General linear power requirements. The VBA3200-100 is a 00-3200MHz high power amplifier, designed primarily for EMC applications. It is based on our GaAs technology, offering the user the benefits of linearity, ruggedness and efficiency. With its compression point close to saturated output, it is equivalent to TWT amplifiers of twice the output power.
-
Product
Two Phase AC Motor Drive
MS 2014
-
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
