Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
GPS/GNSS Antenna Signal Splitter 3-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS321
-
INSTOCK Wireless Components, Inc
GPS321 is a three way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Tinned Ends, 2m
A068VMR-T-6C200
Cable Assembly
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
Product
Portable Connector End Face Geometry Interferometer
-
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
Product
Smart Optical Time Domain Reflectometer OTDR
BD900 Series
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD900 series of Optical Time Domain Reflectometer has excellent dead zone performance and wide dynamic range. There are four models to choose from and that can betterly meet the customer’s specific measurement requirements. Combined with the visual fault locator, it can easily find the breaks, bends, splices, faulty connectors, and other causes of signal loss.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A015DM5-T-0A200
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
COM Express
Computer on Module
COM Express, defined by the PCI Industrial Computer Manufactures Group (PICMG), is the most successful Computer-On-Module (COM) standard in the embedded market today. COM Express employs a mezzanine-based approach, whereby an off-the-shelve module with two 220-pin board-to-board connectors, plugs into a custom, application-specific carrier board.
-
Product
VFL Power Meter -- VFL & OPM
TM203N
-
◇ Self Calibration◇ Self Auto Off◇ High Accuracy, high ,High sensitivity, high linearity-◇ Stable VFL Output◇ Set the REF Value◇ Real-time display of the power consumption◇ Interchangeable connectors: FC/ SC◇ Rubber Out shell, increased the protective properties for field work
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
Test Port Adapter
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
37-Pin D-Type Female Right Angled PCB HV
40-963-037-RF-HV
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Rear I/O For VPX703, VPX RTM
VRT703A
-
The VRT703A is a 3U VPX Rear Transition Module providing I/O expansion for use with the VPX703. The VRT703A provides an easy access to the I/O ports routed to the P1 and P2 connectors of the VPX703. These includes dual PCIe x4, dual USB, RS-232 for both management and payload, dual 1553 ports, JTAG for CPU, dual GbE as well as mSATA socket for storage.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-004
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PCI Converter
ES-200
-
The eSATA PCI BRACKET takes the blazing speed of eSATA outside your computer case with this external plate adapter. Simply install the PCI plate in an open PCI slot on your computer and attach the SATA cable to an available motherboard connector. Now you have an external eSATA port.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 2m, Screwlocks
A068SMR-T-6B200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
12-Bit, 2.5 GSPS Digitizer Optimized for Pulse Detection
ADQ32-PDRX
Digitizer
ADQ32-PDRX acquires the input signal via a single connector and uses an onboard splitter to separate the signal into two paths with different gain settings. The high gain path is used to accurately capture low-amplitude portions of the input signal whereas the low gain path ensures the acquisition of high-amplitude peaks without causing saturation. The two signal paths are then combined in real-time inside the onboard field-programmable gate array (FPGA) to create a digitized output with improved performance.PDRX increases the dynamic range by 3 bits and is fully integrated into the digitizer for fast and easy system-level integration. ADQ32-PDRX is therefore comparable with a 16-bit digitizer in terms of dynamic range, but with the benefit of offering a higher sampling rate.
-
Product
Flexible Cable Set, 2.4 Mm To 3.5 Mm
85134F
-
The Keysight 85134F is a 62.9 cm (24.75 in) long1 flexible cable set composed of a 2.4 mm female2 to PSC-3.5 mm female connector and a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85134F is less than 0.12 dB and phase is 0.13*f+ 0.5°, where f is frequency in GHz.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω MS-M Multiway
40-729A-002
Matrix Switch Module
The 40-729A-001 (PXI) and 42-729A-001 (PXIe) are 8x4 50 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-218-M50-HI
Multiplexer Module
The 40/42-852A-218-M50-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
FMC I/O Module
FM192
-
Sundance Multiprocessor Technology Ltd.
The FM192-R board is designed to fan out the FMC-LPC connector I/Os to four DB9 connectors and one SEIC connector. The FM912-R provides wireless connectivity via WiFi + BLE and 4G + GNSS/GPS modules. 3x antenna connectors (2x for the 4G + GNSS/GPS and 1x WiFi + BLE) are provided for connecting 3x external antennas. Furthermore, the FM192-R provides an IMU sensor, CAN BUS, humidity and temperature sensor and Audio I/O.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A051KMR-C-HA100
Cable Assembly
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
Product
LXI Single 24x8 HF Matrix, BNC (75R)
60-711-005
Matrix Switch Module
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
Product
Universal Multichannel System up to 100V
-
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Cable Assembly 44-Pin D-Type Female to Female, 2m
40-970-044-2m-FF
Cable Assembly
The 44-Pin D-Type Density and a Half cable assembly is constructed from 26 AWG Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
50-Pin IDC Connector for Ribbon Cable - Female
40-961-550-F
IDC Female Connector
Ideal for user created termination schemes where the termination is to be remotely connected by a ribbon cable. A mating 50-Pin PCB connector 40-963-550-SM and IDC Breakout with DIN Rail mount 40-967-550-M are also available.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-032-HI
Programmable Resistor Module
The 40-230-032-HI (PXI) and 42-230-032-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends
A068SMR-T-5A200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Imaging Modules
-
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
Product
High Current Switches
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
Additional Products: 78 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
BNC (M) To Multi-Stacking Banana Plugs
3957
-
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
