Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Closed
42-145A-001-NC
Relay
The 40-145A-001-NC (PXI) and 42-145A-001-NC (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 1m, 250 Port
A500RMR-C-4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Dense Wavelength Division Multiplexer Mux & Demux Module 8 Channels 100G with LC/PC Connector
GLSUN-DWDM
-
Guilin GLsun Science and Tech Group Co., LTD
Wavelength ITU channels 186.6 to 196.1 THz Return Loss ≥ 45 dBDirectivity ≥ 50 dB Connector LC/PCMax. Optical Power ≤ 500 mW PDL ≤ 0.15 dBRelative Humidity 5%~ 95% Dimension 100×80×10.5 mmOperating Temperature -10℃ to +70℃ Storage Temperature -40℃ to +85℃
-
Product
PXI Octal 3:1 High Voltage Power MUX
40-331-005
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SFF
Model 6353
-
- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
PXI Multiplexer Switch Modules
-
We offer a variety of PXI multiplexer (MUX) switch modules.We also offer mating cables and connectors for these modules to ensure speedy and successful system integration.
-
-
Product
PXI 2A Multiplexer, 2-Bank, 8-Channel 8-Pole
40-614-013
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Pressure Measurement Accessories
-
Pressure subbers, connector bushings, grommets, pipe and tube fittings, tube by length, pressure cooling element, pressure and force cables and connectors, air line lubricators, and air filters.
-
Product
Setup Integrity Checker For B2980 Series, Fixed Perpetual License
N1420A
-
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
Product
RF Electronic Calibration Module (ECal), 300 KHz To 18 GHz, 4-ports
N4432D
Electronic Calibration Module
The Keysight N4432D is a precision 4-port ECal module that supports selection of Type-N and 3.5 mm connectors mixed up to 18 GHz. Select either female-female, male-male, or female-male connectors.
-
Product
Convertible GigE Cameras
LUCID Phoenix
-
Compact and budget GigE convertible cameras;Sony II, II and IV generations sensors from 0.4 to 20.0 Mp;Mount support: S-mount, NF-mount, C-mount;Possibility to choose one of three orientations of the camera module;3 types of connections: RJ45, FFC, ix Industrial connector;Polarization model Phoenix 5.0 MP Polarization ModelDimensions: 24x24mm or 28h28mm;Price: from $ 295.
-
Product
Directional Couplers
-
Pasternack directional coupler category is passive devices that couple part of the transmission power in a transmission line. Our directional coupler series provides the bandwidth, high directivity and higher power that engineers need for their most demanding application designs. RF directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack directional coupler components are RoHS and REACH compliant. RF directional couplers are available with 4.1/9.5, 4.3-10, 7/16 DIN, Type N or SMA connectors. Our directional coupler line has 6dB, 10dB, 15dB, 16dB, 20dB, 30dB or 35dB coupling values. Power ratings of our typical and high power directional couplers range from 25 Watts to 70 Watts. Directional coupler frequency range of this product design is from 1 GHz to 8 GHz. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this directional coupler series is in-stock. Not only are these couplers in directional design in stock, they also will ship the same day as they are purchased.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
PC/104 OneBank Carrier
EMC²-SoM
-
Sundance Multiprocessor Technology Ltd.
The EMC²-SoM is a PCIe/104 OneBank™ Carrier for a Trenz compatible FPGA and SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board. It also has I/O pins, using a 100-way Samtec RazorBeam connectors system, the “Sundance Expansion Interface Connector” (SEIC) can be customize for individual applications and bespoke connectors.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-332-HI
Programmable Resistor Module
The 40-230-332-HI (PXI) and 42-230-332-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI Microwave Multiplexer, SP6T, 11-Bank, 26.5GHz, 50Ω, SMA
60-800-311
Multiplexer Module
Our 60-800-311 is a 11 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 0.5m, Spring Latch
A068SMR-T-5B050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
PCI Express-to-XMC Adapter
4876
-
The Technobox, Inc. P/N 4876 PCI Express-to-XMC Adapter is a development/diagnostics tool that permits the testing of a PCIe card in an XMC site. Up to 8 lanes are supported via the P15 connector. Several activity LEDs located at the edge of the board give an indication of key XMC and PCI Express signals and voltages.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18GHz, 50Ω, SMA, Internal Termination
40-781A-021
Relay
The 40-781A-021 (PXI) and 42-781A-021 (PXIe) are single SPDT 18GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
RTM Communication Board
MS 3636I
-
CPCI Rear IO Communication Board is a signal conditioning and interface board for CPCI Integrated Communication Card (MS3635i). This board has required signal conditioning and interface circuits for RS422. Two 96 Pin Euro Connectors are used to interface all IO’s.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 1m HV, Exit Towards Pin 1
A050DM5-F-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
-
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Product
PXI Optical Switch
Optical Switch
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
Product
9025 VXI - 25 Module Solution for VXI
-
The 9025 VXI Receiver is a 25-module solution designed for use with VPC pre-wired interconnect adapters, but can also accommodate a combination of pre-wired interconnect adapters and discrete-wired modules using retainer blocks.1-4 modules attach to an interconnect adapter which in turn is attached to the VXI card. This connector “funnel” forms a complete VXI module, which is easily inserted or removed from the VXI mainframe for maximum flexibility in testing applications. The interconnect adapter also provides room for driver sensors. External cabling to the card is done with a cable clamp or connector located on the top or bottom of the adapter. The positioning of funnels and use of discrete wiring modules can affect the performance of the product. Please contact us for technical assistance.
-
Product
Additional Products: 160 Pin DIN 41612 Cables - Connector To Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Interface Board, Compact, 8:1 Ethernet RJ45
40-965-907
Interface
Compact converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
18" Cables
CONV1553-4
-
Transitions from each SCSI-2 connector on a VME, VXI or CEI-600-6 front panel to two 18" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends.
-
Product
6U High Performance Data Acquisition subsystem
CPCI-AD320
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8320-6U can also accept external scan and trigger signals from a front panel connector.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Tinned Ends
A078HF5-T-0A050
Cable Assembly
The A078HF5-T-0A050 is a 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
