Failure
See Also: Destructive
-
Product
PWB Interconnect Stress Test
-
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
Product
Electronic Cards
-
Our product range includes a wide range of PDBC Relay Card, Local Remote Selector Card, Monitor Card and Fuse Failure Relay Card.
-
Product
Hamburg Wheel-Tracking Tester
-
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
Automated Bondtester
4600
-
The 4600 Bondtester is a benchtop system designed to automatically perform complex test procedures without needing operator input. The system can automatically complete shear and pull test patterns with different orientations of bonds, while recording failure mode images upon completion.
-
Product
Leeb Hardness Tester
HT6561
-
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing Features* Palm size for narrow space.* Test at any angle, even upside down.* Direct display of hardness scales HRB, HRC, HV, HB, HS,HL.* Large memory could store 250 groups including singlemeasured value, impact direction, material and hardnessscale etc.* User recalibration function allowed.* Can communicate with PC computer for statistics andprinting by the optional cable.* Manual or automatic shut down.* Low battery indication.1.3 Technical SpecificationsDisplay: 12.5mm LCD with back lightAccuracy: Display error ±0.8% at LD=900Measuring range: 200-900LConversion: HL-HRC-HRB-HB-HV-HSDMaterials: 9 different common materialsWith RS232C interfaceMemory: 250 data can be stored and re-readableImpact device: D Will handle the majority of hardness testingapplications. Weight: 75gPower supply: 2x1.5V AAA size batteryDimension: 146×65×36mmWeight: 130g (not including batteries)Working temperature： - 10℃～＋50℃Storage temperature：- 30℃～＋
-
Product
Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
Insulation is one of the most important constituents of a transformer. Any weakness in the insulation may cause failure of transformer. To ensure the effectiveness of the insulation system of a transformer, it must confirms the dielectric test. But the power frequency withstand test alone can not be adequate to demonstrate the dielectric strength of a transformer.
-
Product
Failure Analysis – Materials
-
Failure analysis – materials is the investigation into the background or history of a sample, or an event, to determine why a particular failure occurred. A product failure may include premature breakage, discoloration or even an unexpected odor. It is useful to know if this failure is a new, unique occurrence or if it has been an ongoing issue. The investigation can involve analyzing the sample as it currently exists and extrapolating from that data what may have caused the failure. A sample of the “good” vs. “bad” product may also be useful for comparison purposes.
-
Product
Battery Test Equipment
-
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
Product
Radar solution for structural integrity in underground mining
-
OndoSense radar sensors help prevent structural failure in mines by continuously monitoring, for example, deformations and stresses in the tunnel structure. The highly precise, reliable sensors detect even the smallest structural changes with an accuracy of up to 20 μm.
-
Product
ADLINK Software
-
The plug and play Edge IoT solution for machine condition monitoring enabling remote equipment monitoring, health scoring and predictive failure analysis to maximize overall equipment effectiveness (OEE).
-
Product
E-DRIV® Brushless Electric Screwdrivers
NF-Series
-
Designed for high production environments, the E-DRIV® NF-Series feature a high performance brushless motor design that provides durability and reduces the common maintenance costs associated brush type electric screwdrivers. The NF tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management in power tools ensures product quality, cost savings and a reduction in overall ESD failures. The versatile assembly power tool is available in four different model configurations to meet the demand of various unique fastening applications.
-
Product
Plasma Profiling TOFMS
PP-TOFMS
-
Plasma Profiling TOFMS addresses the needs of materials scientists across a wide range of application areas. PP-TOFMS provides fast elemental depth distribution of any inorganic material. The speed and ease of use of PP-TOFMS permit to reduce optimization time of growth processes as many research scientists strive to reduce the time from discovery to applications of new materials.The simultaneous full coverage of TOFMS available for each point of depth permits the detection of non suspected contamination. This is key for failure analysis and optimization of thin film processes that tend to no longer be based on ultra-high grade methods (i.e. ink jet printing…).
-
Product
Non-Contacting Video Extensometer
AVE3
-
The AVE3 is Instron’s most advanced extensometer, engineered for high-precision, non-contact strain measurement across a wide range of mechanical tests—including tension, compression, and flexure. Its adaptable design accommodates various specimen types, sizes, and elongation ranges, making it ideal for everything from delicate films to robust metals. By eliminating the need for clip-on devices, the AVE3 streamlines setup and ensures uninterrupted data collection through specimen failure, even in high-energy break scenarios, such as composites. Compatible with environmental chambers and fluid baths, it supports non-ambient testing with ease. With compliance to ISO 9513 and ASTM E83 and a fast 500 Hz data rate, the AVE3 delivers reliable performance for demanding testing standards.
-
Product
Pressure Hull Penetrator
-
Submarine hull penetrators are used to bring a circuit (electric, fiber optic, and/or RF) from outside a submarine pressure hull to the inside, while assuring under all operating and failure modes there is no leak path to the inside of the submarine.
-
Product
Failure Analysis
-
Failure analysis on electronic components is a continuous challenging task. The smaller transistor dimensions, increasing functional complexity and changing device packaging styles requires new tools and skills for sample preparation, fault localization techniques, high resolution imaging and analysis.
-
Product
Manufacturing Defects Analyzer
406A
-
The 406A is designed to target the highest number of assembly failures for the least amount of capital equipment cost, programming time, and maintenance costs. The precision Stimulus Measurement Unit provides AC/DC analog measurements that are accurate, stable, repeatable, and reliable.
-
Product
BF-Series Angle And Auto Reverse Models
-
The E-DRIV® BF-Series angle and auto reverse models is designed for installing heli-coil screw thread inserts, as well as light tapping and gauging applications. The assembly power tools feature the brushless motor technology and is engineered for precision torque control. These installation tools feature the ability to set and adjust the speed, the rotation (number of turns), as well as program an auto reverse function. Using the assembly tool in conjunction with a torque arm enhances the installation process. The electric screwdriver offers an adjustable speed setting. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Insulating Oil Testing
-
Insulating materials are the elixir of life of electrical equipment. These materials lose their insulating and cooling properties due to impuri ties and ageing. This damages equipment, causes failures and is consequently often accompanied by high costs. Precise and reliable measurement results.
-
Product
Power Supply 650W
UEP10M52-53 / CEP10M52-53
-
The UEP10M52 series is a UEP10M variation with a maximum current output on +6V or -6V (asymmetric) and without +/-12V for use in CERN type CAMAC crates with a maximum 650W power output. The power supply has all the standard features of the UEP10 family as high precision and lowest noise DC outputs and a cut-off protection for overload, over- / and under voltage and over temperature failures.
-
Product
Test Data Management
-
Web-access to all tester records and analyticsUUT History/Event ReportRaw data support, including waveformsComplete Serial Number History ReportCharacterize and CorrelateStatistical Process Control (SPC)Failure Paretos
-
Product
SuperHeater Overheat Protection
SHOP
-
The SuperHeater Overheat Protection (SHOP) system is a proprietary technology that helps mitigate the risk of superheater tube failure due to short-term overheat during boiler start-ups. SHOP assists operators in the management of boiler start-ups by enabling the detection of superheater tube clear events (TCE’s).
-
Product
ERP Testing
-
Signing up for an ERP package is a big decision for any enterprise since it is closely related to key business processes and has the potential to significantly enhance the customer service and experience. To ensure an optimized return on investment, it is critical to have a successful roll-out with the desired features and benefits. With a high failure rate for ERP implementations, it is very crucial to have a comprehensive QA strategy and expertise. TestingXperts offers you specialist QA and solutions for ERP testing and ensures that your ERP systems function properly and meet your business needs. We have subject matter expertise on leading ERP QA packages, coupled with best-in-class QA processes, frameworks and accelerators to help you achieve your ERP goals. Our expert ERP software testing experts have the ability to test features of core applications end to end and also keep pace with the evolution.
-
Product
Motor Termination Units
-
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
Product
Cable Test Box
-
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
Product
Scanning Electron Microscope (SEM)
Prisma E
-
Prisma E scanning electron microscope (SEM) combines a wide array of imaging and analytical modalities with new advanced automation to offer the most complete solution of any instrument in its class. It is ideal for industrial R&D, quality control, and failure analysis applications that require high resolution, sample flexibility and an easy-to-use operator interface. Prisma E succeeds the highly successful Quanta SEM.
-
Product
Digital Thermo Hygrometer
KM-918
-
Kusam Electrical Industries Limited
For production, processing, packing or storing any goods, moisture plays silent role in damaging the goods. It affects finished goods & machinery. Moisture spoils food, medicines, chemicals etc., It also causes frequent breakdown due to corrosion. Moisture causes different problem in different industries. It causes loss of freshness, crispness, flavour & shape in food industries; corrsion of PCB’s component failure, condensation on Ic’s etc. To monitor the humidity we offer 3 types of Digital Thermo Hygrometers.
-
Product
Engine Test
-
The engine test bench is a facility used by engine manufacturing plants to validate internal combustion engines before fitting to the vehicle. OEMs perform ‘Hot’ or ‘Cold’ testing operations in order to measure several physical variables and to diagnose any failure of parts or components. Jackmark Engineering provides bespoke rugged electrical test connection leads suitable for the industrial environment of petrol or diesel engine testing.
-
Product
Acoustic Microscope
AMI D9650
-
Specifically designed to serve as a general purpose tool for failure analysis, process development, material characterization and low volume production inspection, the capabilities of the D9650 are truly unmatched. Representing the latest in C-SAM acoustic micro imaging, the D9650 delivers the unrivaled accuracy and robustness that you would expect from Nordson Test & Inspection instruments, plus improved electronics and software that raises the performance level for laboratory acoustic microscopes.
-
Product
Analytical Probe Station with Laser Cutting System
LCS- 4000 Series
-
The LCS-4000 Probe Station with Integrated Laser Cutting System gives the user maximum flexibility in semiconductor diagnostic cutting, failure analysis, trimming, marking and topside layer removal. All of these functions can be performed on a microscopic level, all on this one system which provides a high level of performance that is remarkably easy to use.
