Leakage
-
Product
Ultrasonic Leak Detector
ULD-410
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
Product
Hipot Line Testers
-
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Product
Surge Arrestor Testing Equipment
SA 30i+
-
SA 30i+, the wireless Leakage Current Analyser from SCOPE is a State of the Art, On-line test system for Residual Life Assessment of Metal Oxide Surge Arresters. The instrument measures and directly displays the values of Total Leakage Current and Third Harmonic Resistive Leakage Current. It provides system harmonic compensation as per IEC 60099-5-B2. It provides Corrected Resistive Leakage Current after applying correction factors for change in system voltage & temperature.
-
Product
8-Ch Sink-Type Digital Output EtherCAT Slice IO Module
AMAX-5056
-
Channels: 8 (Sink Type)Voltage Rating: 10~30VDCRated Current Output: 0.3A per channel at signal "1"Leakage Current: 25 μA per channel at signal "0"Output Delay: From logic level 0 to 1: 10μs; From logic level 1 to 0: 100μs
-
Product
Capacitors - MNOS Series
-
Macom Technology Solutions Holdings Inc.
MACOM’s MIS capacitors utilize a silicon nitride dielectric over a thermally grown silicon dioxide base. The resultant composite dielectric exhibits low leakage current and insertion loss with excellent long-term stability. The temperature coefficient of capacitance is typically +55 ppm / ºC and is ideally suited for high reliability applications.
-
Product
Flammability Test Chamber
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s flammability test chamber complies with IEC 60950, IEC 60695, IEC 60112, IEC 60332 and other standards. We not only provide standard wire and cable combustion test equipment and leakage tracking test equipment and other electrical test equipment as well as a variety of different combustion test equipment, but we also provide customization and can develop professional and high-quality test equipment according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Iron Core Earth Tester
-
Weshine Electric Manufacturing Co., Ltd
Transformer iron core grounding current tester is a high-precision clamp meter specially designed for measuring AC leakage current, current and voltage. Large diameter (80×80mm) can clamp φ80mm cable, or 96mm×4mm flat steel ground wire, suitable for cables Leakage detection and transformer grounding flat steel leakage measurement.
-
Product
1kV DC Hipot Tester For Capacitor
-
AllWin Instrument Science and Technology Co., Ltd.
The max capacitor up to 50uFcharge time is 0~5s; test time is 1~99s( continue set)The max leakage current can up to 300mA
-
Product
DC Hipot Test Set
KVZG
-
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
Product
Digital Clamp Tester With 80mm X 74mm CT With Bluetooth40mmφCT, ACA
MCL-800DX
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Next-generation leakage current clamp meter with connection, via Bluetooth, to a smartphone which displays waveforms and data.
-
Product
SF6 Gas Detection Thermographic Camera
TC706
-
The TC706 displays and signals SF6 gas leaks, without the need to de-energize high-voltage equipment or stop operation. The portable camera also highly improves operator safety by detecting emissions at safe distances and helping to protect the environment by detecting the leakage of environmentally harmful gases into the atmosphere.
-
Product
DC Hipot Testers
DPC series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
DPC series hipots are used for proof testing of high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for electrical equipments. Other areas include: Cable breakdown testing, capacitor charging and general laboratory use.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
Voltage Pulse Generator
SKS-IV10J
-
Shanghai Sanki Electronic Industries Co., Ltd.
The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.
-
Product
High Accuracy Clamp Leaker
-
Leakage Current Clamp Meter, Car Standby Current Clamp Meter, Car Inrush current Tester, Car Charge Current Tester. It is specially designed for online measurement of AC/DC leakage current, current below 600V by adopting up-to-date CT technology and digital integration technology. It is especially suitable for measure car standby current, leakage current, inrush current. It is a product with the characteristic of relatively small size, high accuracy, strong anti-interference capability and automatic shifting.
-
Product
Test Software
-
American Probe & Technologies, Inc.
This new series of software allows you to analyze materials or semiconductor leakage with all of the capabilities of your HP 4140B to resolutions of 1 fA @ 100VDC. Completely rewritten in Visual Basic for Windows XP operating system, it offers Virtual Front Panel Operation of 4140B for I-V & CV Analysis and allows operator to virtually control the 4140B for any instrument operation. I-V Plots with options of displaying current over time. CV Plots with high resolution plotting capability.
-
Product
3W to 10W - Single Output / Multiple Output
PXC-M Series
-
*Industry Standard DIP-24 Package*9-36 Vdc, 18-75 Vdc Inputs*3.3, 5, 12, 15, 24, ±5, ±12, ±15 Vdc Outputs*5 kVAC Isolation (2 x MOPP)*IEC/EN60601-1, ES60601-1, CE Mark*Low Off-Load Power Draw*2.5µA Leakage Current
-
Product
Leakage Current Testing
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
Product
Clamp Meters, Clamp Multimeters
-
Hioki provides a wide range of models for AC, DC, and leakage current measurement. The lineup also includes DC high-voltage probes for measuring the open-circuit voltage of high-voltage solar power (PV) systems. Models that can be easily inserted into narrow gaps between cables and transmit data to smartphones or tablets improve operational efficiency.
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
Electrical Safety Multi-Analyzer
TOS9300 Series
-
The TOS9300 series is a high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
Product
Radiation And Process Monitoring Systems
ProTK
-
Monitoring of the main steam line for leakages in a PWR nuclear power plant with a wide-range gamma ionization chamber.
-
Product
Integrated Chlorophyll Fluorometer
iFL
-
The iFL is the first instrument of its kind to provide leaf absorptance measurement, first to offer white LED lighting that allows chloroplast migration to occur, first to offer humidity control above ambient, first to offer "walk-away automation", first to offer automated post-processing for the Laisk protocol, the Kok protocol, the Yin protocol and the Flexas chamber leakage protocol.
-
Product
Million Meg Ohm Meter
Model HIR 603
-
Laxtronics Instruments & Controls Pvt. Ltd
100 Kilo Ohm To 100 Tera ohms, Leakage Current 10 Milli Ampere To 1 Nano Ampere, Test Voltage 10 Volts DC To 1000 Volts.
-
Product
Safety Compliance Test System
EN 60601
Test System
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
Product
In-line vacuum test systems
-
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
Product
QAM Shadow
-
ComSonics' QAM Shadow is targeted for in-building leakage detection and ingress mitigation when portability and ease-of-use is most important.contractor work verificationevaluate new property wiringingress detection and mitigationextremely easy to use with one-button operationDOCSIS 3.1 ready to future proof your investmentbuilt-in near-field antenna eliminates the need for external antennas
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
Mini AC Leakage Current Clamp Tester (CE)
M-140
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*40mmφCT window and ultra compact size.*Least affection from the external magnetic field.*Wide current measurements.(AC0.01mA-300A)
-
Product
HV Test System for Patient Monitors
Test System
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
