Verifiers
-
Product
Reliability Testing
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Product
Patient Simulators
-
Patient Simulators - also known as physiological simulators are essential tools for biomedical personals to accurately test and verify the performance of patient monitoring systems such as cardiac monitors, ECG machines. It simulates physiological parameters such as ECG, arrhythmia waveforms, blood pressure, respiration, temperature.
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
End to End Testing
-
TestOrigen Software Testing Services Pvt Ltd.
End to End Testing basically refers to the method that verifies the application is performing according to users demand. While executing the E2E test, the complete software system from beginning to end is certified. This is done after functional and system testing and is also carried out as a regression test to validate and verify any patches or changes.
-
Product
Waterproof EC Tester High with ATC
ECTestr High
-
ECTestr Low tester series can measure natural water, verify reverse osmosis system operation and tap water quality. Check nutrient solution concentration in hydroponics applications. ECTestr High models measure salt water, wastewater, cooling tower water, and boiler condensate. Measure salinity for ponds and recirculating systems.
-
Product
Network Service Tester
-
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is well suited to verify the functionality, availability and performance of network services and value-added services.
-
Product
Nuclear Safeguard Systems
-
Nuclear Safeguards are measures to verify that States comply with their international obligations not to use nuclear materials (plutonium, uranium and thorium) for nuclear explosives purposes. Global recognition of the need for such verification is reflected in the requirements of the Treaty on the Non-Proliferation of Nuclear Weapons (NPT) for the application of safeguards by the International Atomic Energy Agency (IAEA). Also, the Treaty Establishing the European Atomic Energy Community (the Euratom Treaty) includes requirements for the application of safeguards by the European Commission. Organizations such as the IAEA and EURATOM and others are tasked with ensuring declared amounts of material are indeed present in the facilities in which they are stored and that such material is not being diverted to other uses.
-
Product
Ultrasonic Leak Detector
ULD-420
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
Product
10Gbit Ethernet Test Engine
XGT-200
-
The Ethernet test engine XGT 200 provide a comprehensive test for next generation Ethernet solution. There are many different test modules, it can help clients to verify the performance of their Ethernet. XGT-200 have two 10/100/1000Mb/s RJ45 , two 100/1000M SFP and two 10Gbps SFP+ it can generate test profession streams that you need and analyze them ,then provide the test result. XGT-200 provide install and maintain services and activate new profession service. XGT-200 can provide many kinds of test functions, it can help you to control and know the quality of your Ethernet.
-
Product
Hygrometers
-
A hygrometer is a device used to measure humidity. Many hygrometer products also measure temperature. A hygrometer that measures both humidity and temperature often is referred to as a thermo-hygrometer. PCE Instruments (PCE) offers a wide variety of hygrometer products used to measure the relative humidity of the air.Since humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of hygrometer devices designed for specific applications such as measuring the humidity in bales of pressed hay or in rolls of paper. A hygrometer also can be used to evaluate heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, a hygrometer capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT). A combination hygrometer / thermometer, or thermo-hygrometer, can be used to verify the integrity of the cold chain during the transport and warehousing of refrigerated food and pharmaceutical products. This versatile and popular style of hygrometer also is ideal for evaluating the performance of HVAC systems in industrial, commercial and residential properties. If the humidity indoors is too high, mold can occur. Certain types of mold cause respiratory problems and other negative health effects for people living or working in the surrounding environment. In addition, mold that has permeated into the walls or roof of a structure must be removed for safety reasons. Mold remediation and removal, also called mold damage restoration, can be a costly endeavor, which is why preventative monitoring of the humidity indoors is preferable whenever possible.
-
Product
Raman Spectrometers
-
The extensive Raman spectrometer family from Anton Paar offers the right instrument for what you want to do: Identify unknown substances, verify samples in quality assurance, analyze the chemical composition of samples, or monitor their changes.
-
Product
NVIDIA® Jetson™ TX2-based Industrial AI Smart Camera for the Edge
NEON-2000-JT2 Series
-
ADLINK's NEON-2000 Series of the NVIDIA® Jetson™ based industrial AI cameras, integrate the Jetson™ Xavier NX or Jetson™ TX2, image sensor, optimized OS, and Rich I/O for vision applications in a compact chassis with verified thermal performance, saving users' Total Cost Ownership on integration and trouble shooting, as well as minizing footprint and cableing required for installation.
-
Product
Connect Generators to the Grid
GridCode
-
DIgSILENT has developed a new verification tool called DIgSILENT GridCode. The software has been designed in response to the need to verify whether a conventional or renewable power plant is compliant with local Grid Code interconnection requirements on basis of generating unit tests. There is a new trend towards verification of requirements at the point of interconnection of a power plant using transient stability simulations with numerical models. An increasing number of Transmission System Operators are including model validation methods to quantify the risk and uncertainty when using these simulation models in stability studies. These new methods have been included in the DIgSILENT GridCode tool.
-
Product
PNA Microwave Network Analyzer
N5222B
Network Analyzer
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Viscosity Standards
-
Brookfield Viscosity Silicone and Oil Standards provide a convenient, reliable way to verify the calibration of your Brookfield laboratory viscometer/rheometer.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ICP® Shock Accelerometers
-
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
-
Product
6 Slot VPX PCIe Gen2 Chassis
Desert Gecko
-
The 6 slot conduction cooled chassis can dissipate 120W in a non-moving air environment. The fin design and wall thickness was designed and analyzed with Flowmetrics software and designed for minimum delta T offset in an average thermal load application. The design was then verified in real life enviromental chamber experiments with a sealed chassis using our 3U heat simulator modules. Data available upon request.
-
Product
Network AutoTester
LinkRunner® AT
-
Test and validate copper and fiber Ethernet connectivity in less than 10 seconds. Validate up to 30W 802.3af/at PSE with TruePower™ loaded Power over Ethernet (PoE) test. Verify twisted-pair cable length and wire-map in a snap.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm With SPDT
50-293-113
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k
40-293-031
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Generate MC/DC Test
VectorCAST/MCDC™
-
Modified Condition / Decision Coverage (MC/DC) provides two levels of verification for conditional expressions. The first level, named MC/DC Branches, tracks each subcondition in an expression to verify that is has been tested with both True and False values. The second level, named Equivalence Pairs, verifies if each subcondition can affect the value of the condition. This is done by generating a truth table for the expression, and then finding a pair of rows in the table that will generate a different result when all values except the tested value remain constant.
-
Product
Pocket-Sized Analyzer for Capturing & Decoding USB 2.0 Devices
Mercury T2C / T2P
Analyzer
The pocket-sized Mercury T2C & T2P capture and decode the widest range of USB 2.0 device classes plus Type-C link states and Power Delivery 3.0 messages. Both the Mercury T2C and T2P utilize the industry leading CATC Trace analysis software for verifying and debugging USB and PD protocol issues. Now there are two base models to choose from; the original Mercury T2C and the new Mercury T2P, which adds the Power Tracker graphical view of VBUS and CC voltages.
-
Product
In-Circuit Test System Calibrations
Test System
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
Product
RZ Family of 64-Bit & 32-Bit Arm-Based High-End MPUs
RZ/G
-
RZ/G Series MPUs extends the capabilities of RZ/A Series to deliver high-end performance for graphics, multi-stream video, and embedded vision thanks to features like camera input, 3D graphics accelerators, Full HD video codec, and GbE. Renesas also offers the RZ/G Linux platform, which is a user-friendly software development environment for customers who wish to lower the barriers and cost of Linux adoption and maintenance. The RZ/G Linux Platform enables super-long-term Civil Infrastructure (CIP) Linux support in an industrial grade verified Linux package, which complements Renesas’ high quality silicon.
-
Product
Pressure testing solutions
-
Pressure testing involves applying stored energy to an assembly of parts, in order to verify its strength, its integrity and/or its functionality. Pressure Testing generally uses the application of a test fluid (liquid or gas) into a volume and the fluid is then pressurised to exert pressure forces onto the test object that can be measured.
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
8 Series Optical Clock Recovery
-
The 8 Series Optical Clock Recovery is a fast, flexible and reliable instrument for assisting in the validation of current and future optical designs. With all the applicable standard rates in the 26 and 53 GBd data rate ranges – no options required – the TCR801 Optical Clock Recovery is a crucial component for any bench or rack aimed at verifying the latest high-speed optical standards. Featuring quick lock capabilities and a sensitive front end for low power signals, this instrument simplifies the challenges associated with today’s optical testing.
-
Product
Automation Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Automation Testing is basically performed for verifying the software product and saving the testing efforts by using various best test automation tools to reach the software product’s quality at time. Automation Testing has become important with the developing difficulty of any software app and it requires the successive test protection within the deadline, due to which the automated software testing is performed to get the best accuracy and productivity at a given time.
