Verifiers
-
Product
Flow Meter / Monitor
NivuFlow Mobile 600
-
The NivuFlow Mobile 600 was developed particularly for long-term measurements in field operation without external power supply. Measurements for checking and verifying can be carried out with the self-sufficient and portable system without any problems even in harsh environments. Battery lifetimes of several weeks or even months reduce personnel costs for maintenance and data readout significantly.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
Structural Testing
-
Structural testing is used to verify the static strength, or fatigue strength, of a component by applying measured loads. Testing can be done to failure, to contractual requirements, or to validate finite element model predictions.
-
Product
Tx/Rx BenchBlade
-
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for logic card characterization. The card includes a HM-ZD male right angle connector segment for access to the Zone 2 connectors of a switch fabric or node card. Edge-launch SMA connectors are utilized for ease of test cable attachment. SMT pads are included on the receive pairs.
-
Product
RTM ThermalBlade
-
This ATCA compatible design offers the flexibity to verify the thermal characteristics of your Advanced TCA chassis, logic cards and backplane designs. Used in conjunction with the ThermalBlade the RTM emulates a typical rear mounted logic card. Application component heights and features, airflow resistance and enclosure power dissipation can be evaluated and analyzed.Maximum sustainable watts are 113 with two switches turned on. Watts are dissipated throughout the entire RTM ThermalBlade equally.
-
Product
Inertial And Integrated GPS/Inertial (IGI) Sensor Testing
SimINERTIAL
-
Overcoming PNT/GNSS positioning challenges with precision inertial sensor emulation, for powerful IGI testing. Integrating inertial sensors is an effective way to overcome the weaknesses of GNSS positioning systems. However, it also adds a set of challenges to the development process. Once inertial sensors have been verified, it is necessary to test the complementary positioning systems alongside each other.
-
Product
Validation Software
EraseSURE
-
In keeping with the NIST requirements for data sanitization verification, Extreme Protocol Solutions has developed EraseSURE. This product is a completely separate tool from our XErase product line and is focused exclusively on erasure verification and unlike other Verification tools that can connect to a handful of drives, EraseSURE can verify hundreds of devices simultaneously including laptops, desktops, servers and SAS,SATA,FC and SCSI storage arrays.
-
Product
The Internet Control Message Protocol (ICMP)
ICMP Tests
-
The Maxwell Pro ICMP Test Suite provides a series of tests for verifying correct operation of ICMP. The tests ensure TCP/IP compliance through vulnerability and robustness testing, with tests for ICMP in both the IPv4 and IPv6 environments.
-
Product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
Software Development Kit
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
Product
Integrated Solution for Digital Switching & Fiber Optics Operational Verification
VERTA
-
When incorporated into defense/aerospace ATE, Verta enables reliable, error-free bus communication and interoperability tests to verify performance of high-speed, optically networked military weapon assemblies.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm With SPDT
50-293-112
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Universal In-System Programming Tool
ScanExpress JTAG Programmer
-
ScanExpress JTAG Programmer is a universal in-system programming (ISP) solution designed for convenience and versatility—a modular, multi-functional, and high-performance tool to program, read, and verify Flash memories, serial EEPROMs, CPLDS, FPGAs, and more.Like all Corelis ScanExpress family products, ScanExpress Programmer is a tool for all phases of the product life cycle—whether programming early code during product development, programming production code during manufacturing, or reprogramming units out in the field, ScanExpress Programmer is designed to fit all in-system-programming needs.
-
Product
JTAG Test Procedures
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete “turn-key” service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Industrial M.2 2280 SSD, FIPS 140-2 Certified
SQFFSM8 840F
-
Compliant with SATA III and SATA v3.2 standard, Support LDPC with RAID ECC. Support AES-256 and FIPS verify, Shock resistance, anti-vibration.
-
Product
Sensors And Process Analyzers
-
Process analyzers as inline and online measurement technologies provide real-time data for outstanding process control, which results in high-quality production. Thorough monitoring by process analyzers with up to 100% coverage of process parameters and subsequent documentation ensures optimal compliance. Moreover, monitoring makes transactions verifiable and establishes a basis of trust between suppliers and customers.
-
Product
Structural Analysis Professional Software
Robot™
-
Robot Structural Analysis Professional software provides engineers with advanced BIM-integrated analysis and design tools to understand the behavior of any structure type and verify code compliance.
-
Product
DOI / Haze Meter
807
-
TRICOR’s Hazer Meter and DOI is ideally suited for measuring flat, non-textured high reflectance surfaces. The Model 807A Haze Meter design is in accordance with ASTM E430 and ASTM D5767 (method A) and is used to measure ±3 degrees around the specular lobe centered at 30 degrees in approximately 220 increments. That’s an angular sample size of 1 sample per 1.6 minutes of arc! This allows differentiation between samples with very small differences in reflectance characteristics. Verified replacement for the older Hunter Dorigon II haze meter unit.
-
Product
GENEM-C 100G Ethernet/IP Infrastructure Test Application
-
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Electric Vehicle Charger Testing
EV-TEST100
-
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Product
Thermal Imagers
-
Klein Tools’ thermal imagers allow electricians, plumbers, HVAC professionals, home inspectors and other trade professionals to verify systems and troubleshoot problems needing maintenance based on hot and cold spots displayed on LCD.
-
Product
Phase Sequence and Motor Rotation Tester
PRM-6
-
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
Product
Video and Protocol Analyzer
-
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
Product
Piers and Jetties Testing Equipment
-
The BathyCorrometer is a diver-held unit which will measure the corrosion potential at specific contact points. Although the readings are visible to the diver, a Surface Display Unit can be supplied to verify readings on board a ship or diving platform. If Remotely Operated Vehicles (ROVs) are being used, the UCP1A contact probe or UCP1B proximity probe can be easily installed to carry out corrosion surveys. Simple surveys of marine structures can be carried out by the use of a Marine Survey Kit (see the case study on Dover Harbour Board).
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
-
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
