-
Product
4.0 GHz, 0.6 pF, 1 MOhm Active Voltage Probe
ZS4000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.6 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS4000 is ideal for 2.5 GHz and 4 GHz oscilloscopes.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Transformer Short Circuit Impedance Tester
JYW6300
-
This instrument is mainly applicable to low voltage load impedance test of 35kV and above power main transformers (single phase or three phases) in ex-works routine tests, overhaul tests, pre-tests, and acceptance tests.
-
Product
Load Testing vs. Stress Testing
-
A load test is a planned test to perform a specified number of requests to a system in order to test the functionality of the system under specific levels of simultaneous requests. A load test ensures that a web system is capable of handling an expected volume of traffic, and therefore is sometimes referred to as volume testing. The goal of a load test is to prove that a system can handle the expected volume with minimal to acceptable performance degradation. The threshold of acceptable performance degradation must be defined by the testers as some value considered acceptable to the end user so that users will not bounce from the site.
-
Product
Resilient Modulus and Asphalt Testing System
-
The Resilient Modulus software features built and test sequences, and the capability to specify user defined sequences. Contact stress is automatically adjusted according to the above procedures as selected. Available waveforms include haver sine, sine, square and triangular, along with a user defined waveform selection. Optional peak & valley compensation ensures proper and quick matching of the load parameters. Real time displays of the prescribed versus actual dynamic load or the dynamic deformation measurements by each sensor are always present. Deformation ratio of the two sensors, Rv (to ensure that the two deformation sensors are in agreement) and Mr are also calculated in real time. During export, curve fitting is done to fit the results to models that predict Mr as a function of σm, σd, and CP (cell pressure). Four different functions are calculated automatically
-
Product
VXI Module
VDSP-31
-
The VDSP31 is a VXI based, multi-channel data acquisition system and digital servo control module. The VDSP31 offers a complete solution for high performance closed loop applications. The VDSP31 has been designed to solve specific problems related to the control of hydraulic actuators. Signal conditioning modules can be combined on a per channel basis to configure the VDSP31 for load or displacement feedback.
-
Product
Inverter/Chargers
-
A Xantrex inverter/charger is a combination of an inverter, battery charger and transfer switch into one complete system. When AC power is available, the inverter/charger recharges the house batteries. It also allows any surplus AC power to pass through and power downstream AC loads, such as a television set or microwave oven. When AC power is disconnected, the unit inverts DC battery power into AC electricity.
-
Product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
-
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
Product
Micro Vickers Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ MicVision main use in testing materials allows for the measurement of the hardness of small or thin specimens and small areas of larger specimens, MicVision testing is commonly used to determine characteristics of thin sheets, foils, fine wire, epoxies, paints, etc. and is often employed in R&D applications .◆ MicrVision hardness is especially useful in determining hardness variations, caused by hardening, quenching, plating, fabrication, welding or annealing, bonding, etc. Micro hardness testing can be accurately employed using loads as slight as 10 gram, somewhat less and considerably more in certain situation.
-
Product
Power Supply 303d
-
Power stabilized POWERLAB series are high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
Product
16 Channel Power PXI Multiplexer, 2 Pole
40-650-002
Multiplexer Module
A 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. It is suitable for applications requiring switching of either mains voltage or DC.
-
Product
Surface Roughness Gage
1000
-
The Adcole Model 1000 represents the state of the art in surface roughness measurement for crankshafts, camshafts and other cylindrical components. The machine is pre-programmed for optimized workflows. Operators simply need to load and unload the parts. In addition to its unprecedented accuracy, this product is also the fastest system for taking critical surface measurements.The base gage is a rugged, self-standing horizontal granite surface plate with affixed headstock, tailstock and carriage. Scanned data is immediately available for review on the touchscreen monitor or printing.
-
Product
Programmable AC Electronic Load
63800
-
Chroma Systems Solutions, Inc.
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing resulting in reliable and unbiased test results.
-
Product
Composite 2×12 Video Distribution Amplifier 12VDC
VDA212RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
Switch
TOE 9261
-
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
Product
Motion Control
-
The ACE products in this segment enhance the quality of any type of movement. Anyone who wants to raise or lower loads, regulate the feed of an object to the precise millimeter or gently decelerate rotating or linear movements will find the right solution here.
-
Product
Electrical Power Transducers
-
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
Force Logger Sensor
NUL-211
-
This sensor can measure the mass to weightrelationship and study how different pulleysystems affect the effort needed to lift weights.It can also be used to measure push/pull forcesand impacts. There is a hook at the bottom of the force sensor that can be connected to various pulling loads.
-
Product
Electronic Loads
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
OSFP-XD Thermal Load with a Controller Board
-
In an everchanging industry, new form factors are launched to support higher speeds like 800G and later, 1.6T. With the speed per lane increasing exponentially, the need for thermal and cooling tests also rises with new requirements and demands.MultiLane is offering a OSFP-XD thermal load with a controller board, with the goal of emulating transceiver thermal behavior, but also to test cooling systems.
-
Product
PXI 10A Power MUX, 2-Bank, 8-Channel
40-661-102
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Rad Hard Power Sequencing
-
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
Product
Programmable Oscillator Amplifier
Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
Product
ARINC BusTools Software Analyzer
-
BusTools-ARINC is the only solution for Bus Analysis, Simulation, Maintenance and Data Logging of ARINC 429, 575, 561/6-wire, 717 and CSDB databus protocols. Simultaneously control, log and display data from a single Windows-based program on USB, PCI, CompactPCI, PCI Express, ExpressCard, PC/AT, PC/104 and PCMCIA platforms. BusTools-ARINC provides comprehensive monitoring, data logging and simulation for 100% bus loading activity.
-
Product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
-
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
Product
Programable Power Supply & Programable Electronic Load
EL-820P
-
*Digital button control and easy operation*High resolution(20mV, 10mA, 0.1W, 0.1Ω)*Overload prevention function*9 sets programmable memory*4 sets real time display*Voltage range: 1V~63V*Current range: 10mA~15A*Maximum power: 200W*Operation mode: CV, CC, CP and CR*Built in USB interface
-
Product
PXI 10A Power Multiplexer, 5-Bank, 6-Channel
40-661A-005
Multiplexer Module
The 40-661A-005 is a single pole, 5-bank, 6-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
