-
Product
Actuation Methods for Functional Test Systems
-
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
5 Amp High Accuracy Current Probe
HA5
-
Our HA5 Current Probe covers the measurement range from 20 milliamps to 5 amps, making it the best choice for measuring very small loads and the outputs of CT (Current Transformer) step-down circuits.
-
Product
Motor Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
Product
Loop Calibrator
Model KM CAL-904-MK1
-
Kusam Electrical Industries Limited
• 4-20mA (1kΩ Load, 24V Loop Output).• 0-20mA and 0-24mA output ranges.• 0.025% Basic Accuracy.• Auto Ramp and Step functions.• 0-100% output with percentage step option.• 0-24V DC voltage source.• Open loop and overload buzzer alarm.• Low battery indication.• Simple Operation Interface• Warning beeper when output is open• Pollution Degree 2.• Ambient temperature 0~40℃.• Power Consumption 150mA at 24V 1kΩ load
-
Product
Load Cells for Weighing
-
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
Shunt Reactors
-
ENTES Shunt Reactors are high quality devices which are designed to meet the inductive load demands.
-
Product
Electronic Circuit Breaker Unit
-
The CorePower® DC or AC Electronic Circuit Breaker Unit replaces conventional thermal mechanical circuit breakers and functions as both a breaker and a switch for controlling loads. By placing ECBUs closer to loads, aircraft manufacturers gain a significant reduction in wire weight, need fewer system components, and lower installation labor costs while increasing safety, efficiency, and reliability. This new smaller unit requires less space and provides more flexible mounting options.
-
Product
24V / 400 Amp Load
BD12-24P-12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 24V battery systems and is extremely cost effective.
-
Product
Low Voltage Container Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Container load banks are portable, self-contained solutions for testing and maintaining large power systems, designed to be easily transported and deployed in a variety of environments, making them ideal for both temporary and permanent installations.
-
Product
Solid-State Demand Recorder
SSR-6000
-
The TransData SSR-6000 is a Load Profiling Interval Pulse Data Recorder used for recording and profiling pulse data received from electricity, gas and/or water meters. The SSR-6000 features a cover-mounted optical port and remote communications via integrated digital cellular, ethernet, telephone modem or RS232 communications options; and includes totalizing capability for aggregated metering applications.
-
Product
2WD Dynamometers
MD-1750 Series
-
The MD-1750 has the largest set of rollers in the industry at 50-inches. The 1750 Series is designed for customers whose horsepower testing requirements and drag racing slick tires require a larger, tire-friendly roller configurations. The MD-1750 is available with a wide 96-inch outer track for testing large Diesel Trucks. When coupled with the SE or DE eddy current option, the MD-1750 is capable of properly loading and testing very large diesel trucks without worrying about tire slippage.
-
Product
Digital Force Gauge
-
Guangzhou Amittari Instruments Co.Ltd
The digital force gauge is a kind of simple and convenient multi-functional instrument for high-accuracy push force and pull force test. It is widely used in electronics, building hardware, textile, auto parts, ignition device such as lighter, fire fighting equipment, pen manufacturing, lock manufacturing, fishing gear, chemical, power machinery, scientific research institutions and other industries. For the push and pull load test, plug and unplug force test and destructive test etc.
-
Product
High Current 45 Relay PXI Card
GX6315 Series
-
The GX6315 is a 45 channel, high current relay board that plugs directly into any 6U PXI slot. The GX6315 also provides nine transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
Product
48V LOADpro Dynamic Test Leads
185
-
This new version of LOADpro is capable of loading circuits as high as 48 volts. 185 can be deployed on electrical systems ranging from 12 volts up to 48 volts. Applications include automotive, heavy-duty, marine, off-road, agriculture and electric vehicles. 48V applications include electric equipment, lift trucks, scissor lifts, golf carts and other battery powered vehicles.
-
Product
Arbitrary Load-Impedance X-Parameters
S94520B
-
S94520B Arbitrary Load Impedance X-parameters enables an X-parameter model to be collected over a user defined set of load impedances. S94520B still requires an application to control the load impedance such as S94521B or Maury ATS or IV Cad.
-
Product
Electronic Loads
-
Electronic loads are indispensable tools in several fields of electrochemistry, for example in the research of batteries and fuel cells. Using an additional external power supply you easily can extend an EL to a two-quadrant potentiostat you need e.g. in the field of electrolysis.
-
Product
Motor Test for Electric Scooters
-
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Sometimes you may need additional loading for abnormal testing (i.e. overload test). Other times, you may need additional loading to simulate worst case normal operation conditions (i.e. input test, temperature test). No matter what your application, we have the loading device to fit your needs! TECH NOTE: Be sure to request our outline titled "Selecting Loads" for assistance in determining the proper rated device for your application.
-
Product
Battery Monitoring System
BMS-3923
-
Kongter Test & Measurement Co., Limited
This battery monitoring system is an innovative solution to measure battery condition with communication way of Power Line Carrier (PLC). With multi-frequency measurement, users can monitor and analyze battery in all aspects: internal resistance, voltage, current, capacitance, temperature and so on.Based on our years experience for battery management system, we build very mature mathematical model that precisely predicts battery capacity. This will in another hand reduce the time that we spend on capacity measurement using a battery load bank.
-
Product
Power Line Isolators & Conditioners
-
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
110V / 100 Amp Load
BD12-110P-48/24
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
Automation Testing Services
-
QACraft has been one of the leading companies in providing automated testing services for all types of software and applications inclusive of mobile as well as web apps. Our expert team designs the QA strategy to check the various parameters such as functionality, speed, performance, quality, loading time, and much more to give you a detailed report about the same.
-
Product
Smoke Detection Sensor – 120VAC Wire-In with Battery Backup
ENVIROMUX-SDS-120V
-
For warning of smoke and invisible fire particles. Ionization smoke detector. Applications from 40°F to 100°F (4°C to 38°C). Front loading battery door. 9V battery backup (included) in case of power failure. One button design for easy testing and HUSH mode activation control. LED indicates four modes of operation: standby condition, alarm condition, alarm memory and hush mode. Hush mode: silences false alarms for 8 minutes, or low battery warning for 13 hours. Voltage supply: 120VAC. Pre-stripped wiring harness with tinned strands. Audio alarm: 85dB at 10ft. Dimensions: 5" diameter x 1.75" depth. Dust cover prevents false alarms. Tamper resist feature. Links with up to 24 devices. Max distance between first and last device: 1000ft (305m). Alarm memory indicates initiating alarm in interconnected systems. Use compatible relay (ENVIROMUX-RLY-SDS120V) for connection to the ENVIROMUX system or other auxiliary warning devices such as external sirens or stairwell lighting. ENVIROMUX-RLY-SDS120V includes normally open and normally closed contacts. Contact ratings: 10A at 120VAC, 5A at 30VDC. Regulatory approvals: UL.
-
Product
Base Station Antennas
-
Amphenol Procom delivers state-of-the-art Base Station Antenna products for both RF and mechanical constructions. Our innovative approach to product development offers the highest quality and our thorough testing protocol guarantees our Base station antennas are the most reliable on the market. We test all of our products performance against dust, water, wind load, temperature and lightning, and many more areas.
-
Product
Basic Heating Module
-
Microwave heating analysis including loads rotation and translation, frequency tuning, heat flow and material parameters modification as a function of dissipated power. QW-BHM (Basic Heating Module) for QuickWave 3D provides a novel regime of operating the FDTD solver: the possibility of simulating microwave heating problems.The software has been prepared to work in sophisticated regimes, modelling rotation and movement of the heated load(s) even along complicated trajectories, etc. Transfer of the heat generated by electromagnetic fields can be modelled with external or internal Heat Transfer Module or by coupling QuickWave 3D simulations to external computational fluid dynamics packages.
-
Product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
-
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
