-
Product
Sampling Boards
MSXB 028
-
Simultaneous Sampling Boards are used in multichannel spectral analysis and other applications that require simultaneous acquisition of several channels. The MSXB 028 usually is used for applications that require interchannel phase measurements such as applications that perform transfer function computations. This board eliminates phase error introduced by sequential sampling.
-
Product
Demonstration Boards
SAMPULSE50GHz and SAMPULSE70GHzANT
-
The SAMPULSE50GHz and SAMPULSE70GHzANT are demonstration boards for Furaxa InP single channel sampler/pulser ICs. The SAMPULSE50GHz model contains a 2.4mm combined TDR input/output connector to the common sampler/pulser node in the IC. The SAMPULSE70GHzANT is similar, except that instead of a single-ended 2.4mm connector, the sampler IC's differential inputs are fed from a bowtie antenna. In both models, the IC's differential sampler output is converted, using an AD8009 op amp, into a single-ended ground-referenced output that is sent to an SMA jack labeled SAMPLER OUTPUT.
-
Product
ISI Channel Boards
M8049A
-
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
Product
Embedded Boards
-
Elma offers embedded computing board level products, including single board computers, mass storage, Ethernet and PCIe switches, FPGAs and custom I/O solutions. Our focus is to provide proven technology based on standard architectures like VME, VPX, CPCI, ATCA, and COM-Express as well as other standard and custom small form factors. We partner with leading board manufacturers.
-
Product
PCI Daughter Boards
DB-24C/DIN (with DIN-Rail mounting kit)
-
The DB-24C has 24 channels of optically isolated digital outputs, arranged into four isolated banks.
-
Product
Burn-In Boards
-
Manufacture of burn-in boards since 1976. Established for more than 40 years in the market, Trio-Tech is recognized and is an approved global supplier to all major semiconductor companies. Trio-Tech has the capability to design and manufacture boards for all system types, with solutions available for many test conditions, Including HTOL, PTC, HAST and 85/85.
-
Product
FPGA Boards
-
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
-
Product
Development Boards
-
Advantech Development boards provide a schematic software & reference to reduce design effort at the development stage. Development Boards have been designed in order to allow customers to verify the functions of COM, text carrier board problems and support COM series. Advantech has designed a Development Board which can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
Product
PCI Daughter Boards
DB-1825/1/DIN (with DIN rail mounting kit)
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
PCI Daughter Boards
DB-24SSRDC
-
The DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Monitor SDR Boards
-
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
Product
Development Boards
-
Everything From Full-Featured to Tiny Starter Boards. Professional, full-featured development platforms, rich in modules. Each Easy Board features on-board programmer or debugger, and supports an entire family range of microcontrollers.
-
-
Product
PCI Daughter Boards
DB-37
-
The DB-37 is a 37 pin female D-sub connector. It has a pin to pin screw terminal for any 37 pin D-sub connector I/O. If you need 2 sub connectors, use DN-37
-
Product
PCI Daughter Boards
DB-1825/2/DIN (with DIN rail mounting kit)
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
PCI Daughter Boards
DB-8R
-
The DB-8R board is the I/O connection board designed for PISO-PS300 and SERVO-300. It is also equipped with 8 form A relays to provide higher current switching capability.
-
Product
PCI Daughter Boards
DB-24PR/24/DIN (with DIN-Rail mounting kit)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Breakout Boards
-
"Breaks out" these pins onto a printed circuit board that has its own pins that are spaced perfectly for a solderless breadboard, giving you easy access to use the integrated circuit.
-
Product
Carrier Boards
ROM-DB5901
-
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
PCI Digital I/O Boards
PCI-822LU
-
Universal PCI, 250 kS/s, 32/16-ch 12-bit Analog Input, 2-ch 16-bit Analog Output with 32-ch Programmable DIO. Replacement for A-823PGH Series, A-823PGL Series, A-822PGH Series, A-822PGL Series, A-821PGH Series, & A-821PGL Series.
-
Product
PCI Data Acquisition Boards
AD8-1250DMA Series - 8 bit, 1.25 GS/s
-
Model AD8-1250DMA contains a 1.25 gigasample/second 8 bit A/D, 8 GB of on-board SDRAM memory and the ability to transfer data directly into the computer system's memory at up to 320 MB/s on 64-bit PCI systems.
-
Product
RTAX/RTSX Adaptor Boards
-
Aldec and Microchip have joined together, offering a new, innovative, reprogrammable prototyping solution for Microchip RTAX-S/S and RTSX-SU space-flight system designs. Unlike the traditional OTP (One Time Programmable) anti-fuse space-qualified FPGAs, the Aldec prototype adaptor uses flash-based, Microchip ProASIC®3E FPGA technology, for design prototype re-programmability.
-
-
Product
Breakout Boards
D Series Boards
-
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
Product
Serial To Digital Interface Boards
-
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Product
Digital Termination Boards
MSTB 008
-
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
Product
ISA Isolated Digital I/O Boards
ISO-LDH/LDL
-
The ISO-LD series is a bus-type isolated loadcell input board. The isolation inputs can operate with up to 500Vrms of common-mode voltage. The ISO-LD series features a 12-bit analog-to-digital converter, on board 1 K bytes FIFO buffer , one loadcell signal input channel, one analog input channel, 8-channel 12-24V isolated digital inputs, 7-channel isolated open-collector digital outputs, one programmable 8-bit LED indicator to indicate the magnitude of strain gauge input signal. The ISO-LD series board is suitable for static force measurement and dynamic force analysis. Because there are on board excitation voltage, high gain amplifier, you don*t have to buy any excitation voltage and signal conditioning module. In other words, it save your money and space.
-
Product
Discrete Module for Multi Protocol 4000 Boards
-
Discrete Module for Multi Protocol 4000 BoardsThe M4KDiscrete is an interface module for the multimode, multiprotocol Excalibur EXC-4000 family of carrier boards. The M4KDiscrete provides a complete solution for developing and testing discrete voltage-level interfaces.The module contains control I/O registers that may be accessed in real time. The module supports 20 discretes. The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels and• Either enable or disable external debounceOutput discretes are open collector, capable of handling up to 32V with a maximum current of 100 mA each. There is a 4092 word FIFO, capable of storing 1023 Discrete entries containing the discrete data and Time tags.
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
