-
Product
PCI Express Digital I/O Boards
PEX-P8R8I
-
PCI Express Board with 8 Isolated Digital Inputs and 8 Relay Outputs. Includes one CA-4002 D-Sub connector and Software Development Kit with Demo Programs
-
Product
Carrier Boards
ROM-DB7500
Carrier Board
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
-
Product
PCI Data Acquisition Boards
AD8-650X2DMA Series - 8 bit, 800MS/s
-
Model AD8-650X2DMA is similar to the AD8-1250DMA, but contains two simultaneous-sampling A/D channels, each capable of sampling at up to 800 MS/s.
-
Product
Intel x51 Based Boards
MS 1507
-
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
Product
PCI Express Digital I/O Boards
PCI-P8R8
-
PCI Board with 8 Channels of Isolated Digital Input and 8 Relay Outputs. Includes one CA-4002 D-Sub connector
-
Product
Multi Protocol Boards
-
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
Product
PCI Digital I/O Boards
PCI-822LU
-
Universal PCI, 250 kS/s, 32/16-ch 12-bit Analog Input, 2-ch 16-bit Analog Output with 32-ch Programmable DIO. Replacement for A-823PGH Series, A-823PGL Series, A-822PGH Series, A-822PGL Series, A-821PGH Series, & A-821PGL Series.
-
Product
Prototype PCBS Printed Circuit Boards
-
Prototype printed circuit boards are manufactured for a variety of reasons; often it is important to manufacture these circuit boards to perform various tests before going through with a full PCB production run. When it comes to prototype PCB boards it’s important to get them made using high quality standards.
-
Product
Single-Function I/O Boards
-
NAI offers, and continues to support, primary or single-function I/O boards designed for a specific, single-purpose application. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements. They are specifically designed for rugged defense, industrial, and commercial applications.
-
Product
PCI Data Acquisition Boards
AD14-100DMA Series - Dual 14-bit A/D, 25 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
Signal Conditioners / OEM Boards
-
Signal conditioners and OEM cards that can be integrated into your system.
-
Product
Carrier Boards
ROM-DB7503
Carrier Board
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
Product
PRODUCTION PCBS PRINTED CIRCUIT BOARDS
-
Printed circuit boards are mass produced for a variety of reasons; it is often the final step after a successful printed circuit board prototype run. Typically, engineers first make and create a design on a computer to test its functionality. Then they prepare a board layout and test with prototypes.
-
Product
Termination Boards
-
Termination Boards for DCS Distributed Control Systems. Available in a wide variety of analog, digital, RTD, and relay options. These boards are for analog input and output modules. It is a general termination board for most kind of analog modules. There are various sizes of boards for users to choose from.
-
Product
Data Acquisition Control Boards
X-GCU
-
X-GCUs are a data acquisition and control boards of Detection Technology’s digital X-ray detector platforms. X-GCU together with the digital X-Cards provide complete and easily scalable detector subsystems shortening time-to-market and delivering total cost savings for all types of X-ray imaging systems.
-
Product
Thermal Test Boards
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
Product
Burn-In Boards
-
Meets burn-in requirements, including extreme temperatures or continual handling. 2 or more layers of polyimide. 200 C maximum temperature. Gold-plated connectors.
-
Product
PCI Digital I/O Boards
PIO-D48U
-
Universal PCI OPTO-22 Compatible Board with 48 Digital I/O channels. Comes with SDK and Demo Programs. Includes one D-Sub Connector and one 50-pin flat cable header. Supports operating temperatures of 0 ~ 60 °C (32F ~ 140F). Replacement unit for DIO-48.
-
Product
Video Detection Boards
VIP-3D Series
-
The VIP series offers multi-functional Video Image Processing modules for traffic control. These boards can monitor single or dual cameras and provide accurate data traffic volume, speed, gap-time, headway, occupancy, concentration, and classification. Data is stored on-board, using non-volatile memory.
-
Product
PCI Daughter Boards
DB-24R/24 (24V)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
Self/Fast Boot use on SKY Boards
-
Each of these loads occur internally to each SKYbolt board at the speed of the internal SKYbolt busses; we are not limited to the speed of the VME bus, the host VME interface or the disk. These program loads also occur in parallel so the startup time is independent of the number of SKY boards in the system.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
Multiprotocol Serial Boards
104-COM-8SM-T
-
This is an eight-, four-, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports RS-232, RS-422 or RS-485 communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors. Common applications include POS, gaming systems, machine monitoring, military and high-density networking.Type 16780 UARTS are used as the asynchronous communication elements.
-
Product
PCI Daughter Boards
DB-16P
-
The DB-16P is a 16 channel isolated digital input daughter board for the A-82X board or any 812pg, 711 726, 720 series board, and PCI-Bus Multi-function boards. The optically isolated inputs of the DB-16P consist of a bi-directional OPTO-coupler with a resistor for current sensing. You can use the DB-16P to sense a DC signal from TTL levels up to 24V. You can also use the DB-16P to sense a wide range of AC signals. You can use the board to isolate the computer from large common-mode voltages, ground loops and voltage spikes that often occur in industrial environments.
-
Product
Evaluation boards
-
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
Product
PCI Daughter Boards
DB-24SSR/D (24-channel SSR Output Board)
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
3U CompactPCI-Serial CPU Boards
-
Advantech’s 3U CompactPCI-Serial board offers latest Intel Xeon®/Core™/Atom based processor blades.
-
-
Product
19" Enclosures for 6U VME VPX Boards
R4U8S
-
The R4U8S is a 4U height 19'' Rack Mount Industrial Chassis featuring 8 slots of either VME or cPCI 6U size boards. The R4U8S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications.
-
Product
Mixed function mezzanine side card for CPCI-S CPU boards
SCX-PCIE
-
The SCX-PCIE is a mezzanine side card for EKF CPU boards, equipped with a PCIe® Gen3 packet switch, onboard NVMe and SATA mass storage, and high-speed front I/O.
