Active Filters
Require power to operate, using active devices and passive components in a frequency-selective network, only passing certain frequencies.
-
Product
Wideband Active Filters
-
Analog Devices’ family of fixed and tunable wideband active filters operating up to 28 MHz bandwidth support a wide range of wireless communications, signal conditioning, and RFID applications. Single-channel and dual-channel options are available.
-
Product
Active Filter
J2190A
-
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
Product
Active Filters
-
Analog Devices’ specially designed active filter products can accommodate any frequency response (low-pass, high-pass, or band-pass) and a wide range of frequencies. Our line of continuous time and switched capacitor filters provides simple, flexible frequency discrimination solutions.
-
Product
Low-Noise Filter, 210 V / 3 A
N1298C
Noise Filter
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
Product
High-Current, Ultra-Low Noise Filter, 21 V / 500 MA, 10 Ω
N1298A
Noise Filter
The N1298A Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
Noise Filter
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
Filters
ZF
-
Antenna Technology Communications, Inc.
ATCi offers a selection of filters designed to reject out-of-band interference.
-
Product
Active Probe
-
This probe is designed to help auto-technicians in troubleshooting electrical circuits. Apart from using the normal multi-tester, this probe can be used in conjunction with it by providing additional functions to assist in diagnosing electrical or components faults or failures in the vehicle.
-
Product
Parallel Active Multifunction Filter
SINAF 3.0
-
Lifasa - International Capacitors, SA
The active filters offer the best possible solution to solve the problems related to the quality in the electrical network, both in industrial three-phase installations, as commercial or service installations. These problems are caused, not only by the harmonics, but also by the consumption of reactive power (generally of capacitive type).
-
Product
Active Probes
-
To ensure that as much information as possible is available at your fingertips, the IOM6 Hub can be used to increase the number of FNet ports on the iC5700 BlueBox by 4. Now you can combine our CAN/LIN data capture, analog and digital capture and control, and debug and trace all from one central hardware tool via our Active Probes
-
Product
Active Antennas
-
Is an antenna that contains active electronic components such as transistors, as opposed to most antennas which only consist of passive components such as metal rods, capacitors and inductors.
-
Product
Analog Filter
SIM965
-
Stanford Research Systems, Inc.
The SIM965 Analog Filter is ideal for signal conditioning applications where Bessel or Butterworth filters are needed. Bessel filters offer clean step response (negligible overshoot) and linear phase response, while Butterworth filters provide excellent pass-band flatness with some overshoot
-
Product
Notch Filters
-
K&L Microwave provides notch filters, also called bandstop or bandreject filters, in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design. When considering a particular family of parts, use Filter Wizard (a link button will be provided when appropriate) to determine a specific part number within the given family.
-
Product
dv/dt Filters
-
dV/dT Output Filter Modules effectively protect motors against these high voltage spikes due to the use of motor cables between IGBT based motor drives and motors.
-
Product
Tunable Filters
-
Our Tunable Filters can be used in a wide range of applications from R & D to production. We have both Gaussian, using dielectric multilayer coatings, and Flat-Top, using gratings, filter profiles available.
-
Product
Active Filters
-
Power electronic devices used to enhance power quality by actively compensating for current/voltage harmonics, reactive power, and voltage imbalances.
-
-
Product
YIG Filters
-
With a 30 year heritage developing leading YIG technologies, Teledyne RF & Microwave has unsurpassed capabilities as your single source for YIG filters. Teledyne has a large, self-contained YIG manufacturing and R&D infrastructure that ensures continuous YIG innovations, including the industry’s only YIG filter that “locks” to a desired signal.
-
Product
Filter Testers
-
All filter test equipment from TSI, used for testing efficiencies of filter media and a variety of air filters, including high and very high-efficiency filters, respiratory filters, cartridges, and protective garments, is known for its simple and reliable operation.
-
Product
RF Filters
-
Amphenol Procom has 40 years of experience in developing and producing high quality RF Low- and high-power Filters for professional radio systems, widely used in the Public Safety and Mission Critical radio TETRA networks in Europe. The comprehensive portfolio of Filter products from Amphenol Procom are designed by experienced engineers, and highly used in the HF-, VHF- and UHF radio frequency range.
-
Product
Active Bat Detectors
-
The all-in-one device designed for active bat detection and recording.
-
Product
Filters and Compiners
-
Combine four bands to a common line Multiple broadband configurations, including AWS High power handling with low IM and insertion loss AISG 2.0 compliant
-
Product
Water Activity
-
Water activity defines the energy status of water in a substance or a system. It describes the amount of water available for hydration of materials.
-
Product
Tunable Bandpass Filters
-
Bandpass Filters are available as narrow band filters or wideband filters, supporting bandwidths from .1% to 200%, in configurations of 2 to 18 sections. Filters are available in a Q range of 250 to 10,000.
-
Product
Notch Filters
Power-Pole Notch Series
-
POWER-POLE® Notch Filters offer improved performance and power handling over our MINI and MAXI Notch Filters.
-
Product
Filters / Splitters / Detectors
-
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
Product
Active Splitter for CATV/SATV
HGS02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent, zinc alloy die-casting chassis. *All ports can be passed by DC.* 75ΩBritish F-type connector.* With separate holes for easy installation. *Low noise, high isolation design. *Frequency 950-2150MHz.
-
Product
Active Optics
-
Radiall designs and manufactures end-to-end optical links for massive data transfers in harsh environments.
-
Product
Band Pass Filter
CA0094
-
Filter, Passband 7~9GHz, VSWR 1.7 Max., Rejection DC-5.3GHz≥40dBc, 10.7-13GHz≥40dBc, SMD
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
