Active Filters
Require power to operate, using active devices and passive components in a frequency-selective network, only passing certain frequencies.
-
Product
Filtered DC Interface Module
-
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
Product
Active Probe
TETRIS®
-
PMK Mess- und Kommunikationstechnik GmbH
MK presents a unique inline probing system – the TETRIS® Active Probe which can contact adjacent square pins in 2.54 mm pitch simultaneously. 1 MΩ / 0.9 pF
-
Product
5U Grille & Filter Assembly
GF-819
-
5U (8.75") Grille & Filter Assembly Features easily removable, washable media filter.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF120
-
Lifasa - International Capacitors, SA
Accessories: Differential protection
-
Product
R.F. Coupler and high Pass Filter
7415-3
-
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
-
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
-
Product
Filtered Preamplifers
FPA
-
These low noise figure, high gain preamplifiers provide low system noise figure andallow longer antenna to receiver cable lengths. Preamplifiers can be specified withseveral filter configurations.
-
Product
Differential Active Probe, 1 GHz
DP0012A
Signal Probe
The Keysight DP0012A is the 1 GHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
Filters and Multiplexers
-
CAES offers an extensive line of RF filters and multiplexers designed and manufactured using our internal capabilities in machining and component and substrate fabrication.These heritage processes have proven flight pedigree in space, on board Gen 5 aircraft and shipboard platforms. CAES' proprietary plating processes enables industry leading high-Q, low l
-
Product
1.5 GHz, 1.0 pF Active Differential probe
ZD1500
Differential Probe
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
Active Probe, 1 GHz
N2795A
General Purpose Probe
The N2795A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±8 V), the probe can be used in a wide variety of applications.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V
T3LVD20-200
Differential Probe
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V.
-
Product
Active Device Characterization Solution Up To 43.5 GHz For 5G
N5244BM
-
The N5244BM provides the N5244B 43.5 GHz PNA-X network analyzer, application software and accessories for active device characterization up to 43.5 GHz for 5G applications.
-
Product
Filtering Network TAPs
-
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
-
Product
Dual Channel Variable Filter
4302
-
The Model 4302 Dual Filter is a high performance, low priced, general purpose filter for use in the laboratory as well as in multiple channel data acquisition applications.
-
Product
Tunable Optical Filters
-
DiCon's MEMS tunable optical filter offers many advantages over a traditional tunable optical filter; increased accuracy & resolution, a faster tuning speed, as well as a durability that will last for over a billion tuning cycles, all in a compact package. Options are available for either 100 GHz or 50 GHz channel spacing as well as operation in either the O-band, C-band or L-band wavelength ranges.
-
Product
9 kHz Highpass Filter
TBHPF1-9KHZ
-
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
Product
Active Loop Antennas / Magnetic Field Probes
-
Is an active, shielded handheld loop antenna with nearly con- stant antenna factor over the entire frequency range. It can be used for testing according to CISPR, MIL, FCC, EN, ISO, ANSI, ETSI and many other standards.
-
Product
Active Voltage Probes
-
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
Product
Active FET Probe Kit 1.2 GHz, 10x, ±40 V
CT4121
-
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design.
-
Product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
-
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
1.5 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1500 is ideal for 1 GHz and lower oscilloscopes.
-
Product
HandHeld Portable Water Activity Meter WA-60A
WA-60A
-
Guangzhou Landtek Instruments Co. Ltd.
Applications:Can be used to measure the water activity of foods. No matter when and where you need to measure water activity, WA-60A water activity meter is your unique choice.The Water Activity, mainly reflects the amount of free water in the state of food balance, the stability of food and the possibility of microbial reproduction, and the chemical,enzyme and physical changes that can cause the change of food quality.It is often used to measure the dryness enduring ability of the microorganisms. Bymeasuring the water activity of food and selecting reasonable packing and storage methods,the use of preservatives can be reduced and the shelf life of food, grain and fruits andvegetables can be judged.Details:Display:6 bit backlight LCD digital display (3 bit humidity aw,3 bit temperature display)Range:0~1.0awResolution:±0.01awAccuracy:±0.02awSensor:Non conductive humidity sensorSampling Time:5 MinutesOperation Conditions:Temperature:0~50oCHumidity:<95%RHPower Supply:2x1.5V AAA Size(UM-4)BatteryDimensions:135x70x44mmWeight(Not Including Batteries):100gStandard Accessories:Main UnitSample PlateCarrying Case(B04)ManualOptional Accessories:USB Data Cable with SoftwareBluetooth Data Adapter with SoftwareIf any questions please feel free to contact Lisa Li.Thank you!
-
Product
Active Optical Cable
-
Shanghai Tarluz Telecom Tech Co., LTD
Are cables with optoelectronic modules in the connector heads that convert electrical signals to light.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
-
Product
Filter Test System
DU7216/7218
-
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
Product
Interchangeable Probe Active Transmitters
HD2817T…Series
-
The instruments of the HD2817T… series are transmitters, indicators, and ON/OFF regulators with data logging functions, they measure temperature and humidity. The instrument has a large, backlighted, graphical display.
-
Product
RF Filters
-
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
