-
Product
Tri-Temp Pick-and-Place Handler
MT9510 XP / x16
-
MT9510 XP™/ MT9510 x16™ test handler provides full temperature control during test in extreme environmental conditions from -55˚C to +175˚C. A variety of options, upgrades and retrofits are available to configure the product to customer applications such as; automotive battery management systems (BMS) for electric (EV) and hybrid electric vehicles (HEV) and precision power regulators.
-
Product
AC/DC Power Supply 60 W
TR100M150
-
AC/DC power supply with 100 W from Cincon | input ranges 90 - 264 VAC | output 15 V | operates in temperature from -20 to +80 °C | provides 2 MOPP
-
Product
Needle Microprobe
MT-26/2HT
-
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-MU-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Pressure Fittings
-
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
Product
12.1" XGA Elkhart Lake Thin-Client Terminal With Intel® Atom™/ Celeron® Processor
TPC-312 EHL
Panel PC
Industrial-grade 12.1" XGA TFT LCD with 50K lifetime and LED backlightIntel® Elkhart Lake (EHL) Atom™ 6425E 2.00 GHz quad-core / Celeron® J6412 2.00 GHz quad-core processor with 4 GB DDR4 SDRAMTrue-flat touchscreen with 5-wire resistive touch control and IP66-rated front panelWide operating temperature range (-20 ~ 60 °C/-4 ~ 140 °F)Front-facing LED indicators to show operating statusBuilt-in Advantech iDoor technology, SSD/HDD bay and VESA mountCompact, fanless system with aluminum alloy front bezel and chassis grounding protectionSupports Advantech’s SNMP Subagent softwareSupports Advantech’s WISE-PaaS/RMM remote management software
-
Product
Hybridization Oven
REXMED ROV-200
-
MOD. ROV-200, AC 110/230V, Plug type: , Hybridization oven, HS CODE: 841780, UNCCS CODE: 484352, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~85˚C, Stability at 37˚C: ±0.1˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 1KW, Shaking timer: 999/min, 999/hr, shaking timer can be set in second, minute or hour function and at the end of operation audio and visual warning, Motor: Noiseless powerful brushless induction motor 15W, Rotation: 5~60rpm adjustable, Rotator: for 8pcs(optional), Reciprocal: 5~60rpm adjustable, Platform: L30 X W18cm(optional), Rocker: 5~60rpm adjustable, Platform: L29 X W22.5cm(optional), Chamber: L35 X W25 X H25cm, Capacity: 21.9L, chamber with glass viewing window, Optional: Rotator for 8pcs X 1set, reciprocal platform (L30 X W18cm) X 1set, rocker platform (L29 X W22.5cm) X 1set
-
Product
High Accelerated Life Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Rapid Temperature Cycling: Achieves rates up to 100°C/min for accelerated stress screening hass.- Multi-Axis Vibration: Combines pneumatic (6-DOF) and electrodynamic vibration for multi-stress accelerated life testing halt simulations.- Precision Control: halt process ±0.5°C temperature uniformity and real-time monitoring.- Customizable Profiles: Supports stress levels user-defined stress protocols (step-stress, dwell times).- Durability: Robust construction with corrosion-resistant materials
-
Product
Humidity Chambers
FW Series
-
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
Product
NI-9260, 51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module
783466-01
Voltage Output Module
51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module - The NI‑9260 is an instrument-grade dynamic signal generator for testing the audio components and capabilities of consumer electronic devices and providing excitation in structural test applications. Unlike sound card-based solutions, the NI‑9260 can be deployed quickly and recalibrated to guarantee long-term measurement repeatability and decreased test time. It also features ±30 V overvoltage protection and short circuit protection.
-
Product
Robotic and Computer Programming System
Sense
-
Sense is a robotic and computer programming system which allows users to explore, problem solve, and advance their computer programming abilities from just starting in visual block programming, to Python and C languages.
-
Product
4-Slot Distributed DA&C System For Ethernet
ADAM-5000L/TCP
Data Acquisition Module
10/100Base-T auto-negotiation high-speed communication portSupports Modbus/TCP for easy integrationSupports UDP event handling function1500 VDC isolation for Ethernet communicationProvides C and .NET class library to develop applicationsBuilt-in watchdog timer for system auto-resetWindows utility- I/O modules configuration and calibration- Network auto searching- Data stream setting- Current status monitoring and alarm trigger4 I/O slots for up to 64 points data monitoring and controlAllows concurrent access for 8 host PCsAllows remote configuration via EthernetUp to 100 m communication distance w/o repeaterARM 32-bit RISC CPU
-
Product
cRIO-PN-S, Slave, C Series PROFINET Slave Interface Module
782131-01
Interface Module
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
-
Product
Edge AI Inference System
AIR-021
Edge AI Inference System
Edge AI Inference system powered by NVIDIA® Jetson Orin™ NX/Nano and Super mode. Compact and high performance AI box. NVIDIA® Jetson Orin NX 16GB/8GB and Orin Nano 8GB Modules. 12~24V wide power and -20~50 °C (NX) -10~50°C (NANO) supported.
-
Product
USB Temperature Logger
USRIC-4
-
Designed as a Single-use, cost effective & reliable temperature recorder, the LogTag® USRIC-4 measures and stores real time temperature readings over a measurement range of -25°C to +60°C (-13°F to +140°F). The USRIC-4 combines all the features of an advanced temperature recorder with a 3937 log memory and a 6-month operating life in a robust and inexpensive package.
-
Product
CAT III Digital Multimeter
82600
-
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
Standard 1.71 (48.00) - 3.00 (85.00) General Purpose Probe
HPA-74T156
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
DC/AC Inverter 450 W
ODS-750-7281-T
-
DC/AC inverter with 450 W from Premium | input ranges from 9.5 - 15 VDC | output is 120 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
NI-9351, 4-Channel C Series Functional Safety Module
784446-01
Functional Safety Module
4-Channel C Series Functional Safety Module - The NI-9351 works with 24 V industrial logic levels to directly connect to various sensor types, including light curtains, emergency e-stop buttons, and final elements such as relays, contactors, and motor drives. The NI-9351 is an analog input and digital I/O Functional Safety Module capable of SIL 3 certification according to IEC 61508. You can use the Functional Safety Editor to program the safety logic solver, which resides in the module. The module features diagnostics for monitoring the status of hardware and the integrity of the connections.
-
Product
ARINC-429/717 XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-A429
Interface Card
The card design is based on the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, and a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET, LabVIEW, RTOS) architecture. This hardware and software package provides increased system performance and flexibility while reducing integration time.
-
Product
MSR385WD: Data Logger with wireless sensors for operating temperatures up to +125 °C and optional GSM terminal for remote monitoring
MSR385WD
-
Your product description goes here.
-
Product
High Temperature Accelerometer
CM362-7A
-
High Temperature Accelerometer, 650F (343 C) Top Exit Flexible Hardline Integral Cable 25 pC/g
-
Product
Pico-ITX SBC With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, HDMI/LVDS And LAN
PICO512
-
The PICO512 is designed to support the latest 7th generation Intel® Core™ processor or Celeron® processor 3965U. Coming with one 260-pin DDR4-2133 SO-DIMM socket supporting system memory up to 16 GB, the Pico-ITX motherboard also features a PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors for an additional I/O board/signals. It supports a 4K visual experience with dual display outputs through HDMI and LVDS. Pico-ITX SBC can withstand a wide operating temperature range from -20°C to +70°C.
-
Product
6U Switch Board
VP68801
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP68801 is a China local design VPX Switch, compliant with VITA46.0, VITA48, and VITA65 specifications. The Profile of VP68801 is SLT6-SWH-16U20F-10.4.2, which uses Gb Ethernet as control plane and SRIO as data plane. It is mainly applicable to high-speed data exchange and routing among different types of payload boards in a VPX chassis. The switching board is designed as 6U VPX form factor, supporting both traditional air-cooled version and conduction-cooled version. With reliable anti-shock and vibration capability, excellent heat dissipation performance and unique environment protection design, the whole board can be stably operated in the wide temperature environment of -40°C to +85°C.
-
Product
IEEE802.11 Ac/a/b/g/n + BT 5.0, M.2 2230, SDIO-UART
EWM-W194
-
IEEE 802.11ac/a/b/g/n (2.4 and 5GHz) and Bluetooth 5.02TX / 2RX-30 ~ 85 °C (-22 ~ 185 °F)Supports Linux OSNXP 88W8997Interface: WiFi: SDIO, BT: UARTM.2 2230
-
Product
Bus Analyzer / Exerciser
VME850P0
-
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
