-
Product
Tire Pyrometers
52-50640
-
Longacre Racing Products, Inc.
Accurate, super-fast response electronics.Can hold highest temp reached. Compares one temp to another with the push of a button. Low battery indicator and auto shut-off. 2000 Range (tire probe max 500). F or C switchable. Standard coil cord tire probe and carrying case included.
-
Product
10-32 Coaxial Male to 10-32 Coaxial Male, 50 Ohm, 10 ft. cable
786659-01
Coaxial Cable
10-32 Male to 1-Pin 10-32 Male, 50 Ohm Coaxial Cable - The 1032CoaxialM-1032CoaxialM Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
Product
Environmental Testing
-
We have a CTS C-65/100 Climatic Test Chamber available for hire at dB Technology.They have available:*Internal dimensions: 500 x 500 x 400mm (w x h x d)*Temperature range: -65°C to +180°C*Heating rate: 3°C/min*Cooling rate: 2°C/min*Climatic temp range: +10°C to +95°C*Humidity Range: 10 to 98% RH
-
Product
32GB DDR5-5600 2GX8 1.1V SAM
AQD-D5V32GN56-SB
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
Safety Certified I/O Modules
HY-TTC 30XSH
-
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Hydrogen Analyzer
H‑500
-
Determination of hydrogen using the heat extraction method is a special requirement for the characterization of steel, steel alloys, copper and other metals. ELTRA’s H-500 is designed for the rapid and accurate determination of hydrogen in these materials. The H-500 analyzer uses the heat extraction technique and is equipped with a resistance furnace with quartz tube. The temperature can be set up to 1000 °C in steps of 1 °C. The usual working range of the H-500 is about 900° to 1000° C.
-
Product
24 Channel, 1 Form C 5A Relay Switch
DP-cPCI-4455
-
The DP-cPCI-4455 is a 24 channel relay switch module. It provides 250V DC/AC isolation between channels. This module is constructed using 1Form’ C’ SPDT relays.
-
Product
Temperature, Humidity, CO2 Transmitter
H6020
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Digital Waterproof Thermometer
213/2
-
Rubber bumper seals for impact resistanceWaterproof case (IP66 & IP67 protection)Extruded aluminium case for superior durability°C/°F switchableEasy to read LCD display
-
Product
Embedded Engineer
-
Embedded Engineer combines automated source code generation with model-level debugging. The plug-and-play product provides optimized generation of ANSI C code from UML structures, state machines and activity models as well as the generation of C ++ source code. Embedded Engineer also guarantees the traceability of requirements to the code and back again.
-
Product
AC/DC Power Supply 20 W
CFM21S240-T
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 24 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety | JST connector
-
Product
Temperature Measurement IR Sensors & Detectors
ST150 With Diffractive Lens
-
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that delivers a very low Temperature Coefficient of Responsivity of -0.04%/C with a high output voltage, 19.5 FOV and a quick time constant of 38ms. This Low-cost detector comes in a TO-5 package and has a very short thermal shock response to ambient temperature change.
-
Product
sbRIO-9476 , Non-Enclosed, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
783951-01
Digital Module
Non-Enclosed, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The sbRIO‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel. Non-enclosed modules are designed for OEM applications.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
DC/DC Converter 1000 W
CRS-1000-6476-C
-
DC/DC converter with 1000 W from Premium | input ranges 14.4 - 30 VDC | output 48 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
Product
Thermocouple, Contact, Receiver, Chromel, Type K (°C)
610113131
Thermocouple Contact (Receiver)
Primary mating contact 610113133.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
Product
4FE+1FE ST Multi-Mode Unmanaged Ethernet Switch, ATEX/C1D2, -40~75℃
EKI-5525MI-ST
Ethernet Switch Module
Communicates with SCADA software via Modbus/TCPCommunicates with NMS (Networking management system) via SNMPPort-based QoS for deterministic data transmission-40~75°C operating temperature range (EKI-5525SI/SI-ST,EKI-5525MI/MI-ST only)8.4~52.8 V DC wide-range power inputEMS level 3 protection for extreme outdoor environmentsIEEE 802.3az Energy Efficient Ethernet (EEE)Supports redundant 12~48V DC power input and P-Fail relayLoop detection
-
Product
150-Watt AC/DC Power Supply; Dual Output
56MD1
Programmable Power Supply
NAI’s 56MD1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, dual output, at a baseplate temperature of +85° C.
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
Military & Aerospace EMC Testing
-
EMC Technologies’ Melbourne and Sydney and also EMC Bayswater (south-east Melbourne) laboratories provide NATA accredited Electromagnetic Compatibility (EMC) MIL-STD testing of military equipment to MIL-STD 461 B, C, D, E, F & G. The scope includes most test requirements and methods called up by MIL-STD 461/2, allowing defence agencies, contractors and defence suppliers to prove compliance with the stringent EMC limits imposed on defence equipment and systems.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 2m HV, Exit Away From Pin 1
A050DF4-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
DIGITAL TURNS TESTER AND DIGITAL LCRTZ METER
TURNS-LCRTZ
-
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
-
Product
Express Card
DAS-429ExCARD/RT10
-
Both cards contain 64 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table.The card's small size (54 millimeter wide) and suitability for Express Card compatible notebook computers make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle
FE-5121
-
* Emulates AT89C5121 Derivatives with 6/12 Clocks/Cycle * 16K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 16MHz/ 3V, 5V * X1 and X2 Mode Support * MS-Windows Debugger for C and Assembler * Keil mVision2 Debugger Compatible * PLCC-52 and SSOP-24 Emulation Headers * Serially Linked to PC at 115Kbaud
-
Product
Cable, 10 Pos Combicon to Pigtail, 1 Meter
190656-01
Multifunction Cable
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
Product
LTE Cat4+GNSS, Full-Size Mini-PCIe Form Factor, USB Communication Interface
AIW-344
Communications Module
Main Chipset Qualcomm MDM9X072 LTE Antenna Coaxial Connectors +1 GPS antenna connectorLTE FDD:150Mbps DL/50Mbps UL (Cat 4)LTE TDD:130Mbps DL/30.5Mbps UL (Cat 4)Operation: Normal: -30°C ~ +75°C/Extended: -40°C ~ +85°CAIW-344FQ-E02 LTE/HSPA+/GPRS module, with GPS, for EU, for TW, for Australia, for BrazilAIW-344FQ-N01 LTE/HSPA+/GPRF module, with GPS, for USAIW-344FQ-J01 LTE/HSPA+/GPRF module, with GPS, for JP
-
Product
Temperature Transmitter
T4211
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured values are displayed on LCD display. It ispossible to switch OFF the LCD at all.
-
Product
8FE+2G Combo Unmanaged Ethernet Switch, ATEX/C1D2/IECEx, -40~75℃
EKI-5629CI
Ethernet Switch Module
Communicates with SCADA software via Modbus/TCPCommunicates with NMS (Networking management system) via SNMPPort-based QoS for deterministic data transmission-40~75°C operating temperature range (EKI-5629CI/5626CI only)EMS level 3 protection for extreme outdoor environments12~48 V DC (8.4~52.8 V DC )wide-range power inputIEEE 802.3az Energy Efficient Ethernet (EEE)Supports redundant 12~48 V DC power input and P-Fail relayLoop detection
-
Product
Pocket Sized Celsius Scale Dial Thermometer w/ 5 Inch Stem
TC70
-
UEi Test & Measurement Instruments
Celsius scale thermometer with a 1 inch dial and a 5 inch stem with a -40˚ to 70˚C range
