Battery Charge Discharge
-
Product
Battery Pack PCM Test Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
Product
Partial discharge measurement with remote wireless reading
PD-LT
-
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
High Voltage Benchtop Battery Tester 1000V Max input
BT3564
-
Hioki benchtop battery testers support simultaneous high-speed measurement of the internal resistance and battery voltage of EV and PHEV battery packs. The BT3564 Battery HiTester can measure pack voltage and total resistance, as well as bus bar resistance up to 1000V.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Extendable Version
SL1720A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development.
-
Product
DC/DC with UPS and Charge Controller
-
A wide input range, quad output PC/104-Plus DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40 to +85C without a fan or heatsink making it ideal for industrial applications.
-
Product
Hand‐held Digital Battery Tester w/ Thermo Printer, USB port
12-1015
-
• Tests 12V Flooded, AGM, Gel Cell, Enhanced Flooded (Start/Stop Batteries)• 10 Line LCD display• Performs ground test• Checks diode ripple• Stores last 250 test series with or without power• Carrying case, printing software and USB cables included• Built-in thermal printer with thermal paper (611305)
-
Product
Lithium Battery Testing Equipment
-
Fuzhou Fuguang Electronics Co., Ltd.
Lithium Battery Testing Equipment
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Standard 1.24 (35.00) - 2.94 (85.00) Battery Probe
CCA-006
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 78Full Travel (mm): 1.98Recommended Travel (mil): 40Recommended Travel (mm): 1.02Overall Length (mil): 669Overall Length (mm): 16.99
-
Product
CTEK MXS 5.0 Battery Charger
40-206
-
The MXS 5.0 offers a unique eight-step approach to battery care. Fully automatic microprocessor controlled charger with built-in automatic temperature sensor features a unique combination of advanced charging modes and makes the new MXS 5.0 the fastest, most effective and versatile consumer charger CTEK has ever made. Alligator Clamps and Eyelets included.
-
Product
PulseTech Battery Analyzer, 6V and 12V Battery Tester
390PT
-
The 390PT Battery and System Tester lets you quickly, safely and accurately test both 6-Volt and 12-Volt lead-acid flooded, AGM (flat and spiral plate) and gel cell batteries in or out of the vehicle and test 12-Volt and 24-Volt charging systems for proper operation. Combined singe load, dynamic resistance technology and algorithms display battery voltage and capacity in easy to understand results in seconds. The handy "QUICK START" instruction guide is printed on the back of the tester.
-
Product
Battery Pack Rotate Test Device
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Rotate Test Device Single storage cell safety testTest object: Battery storage pack or systemRotate the battery pack 360°around X axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Rotate the batter pack 360°around Y axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Accept standard: Battery pack or system has no electrolyte leakage, no rupture at case, no fire nor explosion. And remain the connection reliable, the structure intact, the insulation resistance value not less than 100 Omega /v.
-
Product
Partial Discharge Test System
TPP
-
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Product
Battery analyzer For Coin Cell 5V20mA
TOB-5V20mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Analyzer (0.1-20mA, up to 5V) Lithium Coin Cell Battery Research. TOB-5V20mA Battery analyzer is an eight-channel battery analyzer to analyze small coin cells with a range current 0-20mah, voltage 0-5v.
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
Test System
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Battery Analyzers
Beta D-50
-
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
Product
Battery Module/Battery Pack Test
-
The battery test system CT3001B and CT3001D provide solutions for battery module/battery pack test with higher current/voltage. They can also be used in situations that batteries are charged/discharged at high rates. Different current/voltage range and channels numbers can be custom made based on the requirement.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
43-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Charge Logger Sensor
NUL-246
-
This sensor measures electrostatic charges. It can be seen as a highly sensitive electroscope indicating whether a charge is positive or negative. Other uses are: to explore the nature of static charge, to measure both charge and voltage, to measure charge by induction, quantify the charge on a capacitor or discover the charge distribution on a conducting sphere.
-
Product
Scienlab Battery Test System – Pack Level
SL1700A Series
-
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increase the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 90 and 270 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
-
Product
Battery Conductance Tester
SAT-AC
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AC Battery Conductance Tester is a multi-function and portable digital data storage measurement instrument to test battery running condition and parameters quickly and precisely. It can display and record many key parameters for multi-groups like battery string and each battery cell’s voltage, conductance, connecting strip resistance, battery’s internal resistance and so on; offer the ability to distinguish battery’s condition effectively and accurately; compose with intelligent PC measurement analyzing software, user can track battery’s decay trend, and alarm beforehand to help technician and administrators process according to status.
-
Product
Automatic Battery Monitor
BA24-2020
-
The BA24-2020 automatic battery tester makes it easy and efficient to test each cell of a battery. It makes it possible to receive a new battery and to revalidate it regularly.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF1200
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations
-
Product
Lithium Battery Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
Lithium battery test chambers are important in this rapid blooming era for electronic products, electric vehicles and storage systems. Lithium-ion Batteries are the widest applied in these products. The battery safety is one of the critical factors before launching such a product into market. And the demand for lithium battery test chambers is growing rapidly.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Cell Battery Crush Test Equipment (Vertical)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Cell Battery Crush Test Equipment (Vertical)Application: Single cell crush test (cylinder, pouch, prismatic cell, etc)Crush Tool: Semi-cylinder, hemisphere (According to test standard)
-
Product
Computerized 8 Channels Battery Analyzer
BTS8-WA
-
BTS8-WA is a precision eight channels battery test system for measuring battery capacity at 0.002mA - 1mA up to 5V.. This systems the best tool to study new generation energy storage materials and rechargeable battery.
