DC Electronic Loads
The current that results from resistive elements of the load on an output.
-
Product
Unclamped Inductive Load Tester
ITC75300
-
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
Product
Adapter, 1.0 mm (m) to 1.85 mm (m), DC to 67 GHz
11921E
Coax Adapter
The Keysight 11921E precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
DC Earth Fault Locator
GFL-T + GFL-R
-
The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
AC Load Bank (Resistive)
K-1000 Resisitive
-
Kongter Test & Measurement Co., Limited
The kW of a resistive load bank is “real” power in electrical terms. When a resistive AC load bank is used to test an engine generator set the engine will produce its full horsepower rating, dissipate engine exhaust gases, and produce thermal energy into the engine cooling system. The resistive load bank in fact, will completely test the engine and its various systems.
-
Product
Electronic Fuel Quantity Indicator
-
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
Product
Electronic Moisture Analyzer
MOC-120H
-
The moisture content of a variety of samples can be measured using an array of drying modes. The drying status can be seen at-a-glance with the fluctuation range display. Active in a variety of fields (cereals, starch, flour, noodles, brewed products, sea foods and marine products, meat products, spices, sweets, dairy products, dried foods, vegetable oils and other food articles; pharmaceuticals; ores; cokes; glass materials; cement; chemical fertilizers; pulp and paper; cotton; various fabrics and other industrial goods); enabling measurement of samples (cereals, foods, and chemical products) under various conditions (powder, particles, paste, and liquid).
-
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
AC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
We offer AC load banks in a variety of capacities and any voltage combination, with custom models including resistive, inductive, capacitive or resistive/reactive combination loads, all tailored to meet any load testing requirement.
-
Product
High-accuracy Multi-channel Programmable DC Power Supply
N39400 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N39400 series is a high-accuracy & multi-channel programmable DC power supply with standard 19-inch 2U design, available for cabinet installation. Single N39400 supports Max. 4 channels output, with channels isolated. Both local operation on front panel and remote control on a computer are supported. N39400 can be widely used in lab test, system integration test, production aging line, etc.
-
Product
Programmable Multi Output DC Power Supply
LQ6324P
-
- Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation
-
Product
DC Ground Fault Locators
-
We currently offer one highly capable DC ground fault locator for sale to the United States, Canada and Globally. This fault locator is highly reliable and highly capable of locating any ground fault in a variety of settings. This one piece of ground fault locator equipment is all you will ever need to find any fault, in any location, in any system. With advanced computations and fuzzy logic it can very accurately display the insulation level of the tested circuit. We offer the best and only ground fault locator you will ever need. To learn more about his product please click below where you will also be provided key features and the ground fault locator specifications.
-
Product
Digital-control DC Power Supply
IT6700 Series
-
IT6700 series power supplies are the most economical power supplies, they have the widest voltage and current utilization, one power supply can replace multiple power supplies, widely used in various testing occasions. With the capacity of 100W, voltage output of 60V, current output of 5A, they can control the change rates of the voltage and current automatically. The power ratio can be up to 3 times. For instance, One IT6720 can subsitute previous 60V*1.6A/32/*3A/20V*5A 3 kinds of models to save your cost.
-
Product
DC DC Converter Models
-
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
-
Product
6 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 6 Ports
GPS612
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Auto Load 4 Moving Probe Tester
AL Series F4H4033AL
-
Medium and High Volume Production Model with Auto Loader. Max. Test Area 15.7 x 13" (400x330mm). Max. Transferable Panel Size 16.5 x 13.4" (420x340mm). Number of Probes 2 Upper, 2 Under. in. Pad Pitch *4 0.00236" (60µm). Min. Pad Size *5 0.00118" (30µm).
-
Product
Load Testing Platform
NeoLoad
-
NeoLoad is the only load testing platform covering you for both Cloud-ready apps, microservices architected apps, mobile and IoT apps and enterprise-grade packaged apps.
-
Product
6/8/12 Volt 0-1000 Amp Heavy-Duty Variable Carbon Pile Load Tester
7136R
-
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Built in LCD Digital Voltmeter and LCD Digital Amp Meter• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• RoHS and CE Compliant• Made in USA of US and Global Components
-
Product
DC Power Supply
PW-3032R
-
*Toroidal Transformer*Low EMI & High EMS*Very Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.3m Vrms Ripple & Noise(C.V.)*<2m Arms Ripple & Noise(C.C.)*Low EMI & High EMS.*Dual Display.
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 90 dB, 10 dB Steps
84906L
Attenuator
The Keysight 84906L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life greater than 5 million switching cycles per section) and an attenuation range of 0 to 90 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Isolated DC Input/Output Module
ADAM-3014
Input/Output Module
1000 V DC , fully isolatedEasy input/output range configurationLow power consumption, 0.85 W (Voltage Output)Wide input/output rangeFlexible DIN-rail mountingOperates from single +24 VDCTemperature range 0 to 70°C
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
Product
High-Performance Autoranging DC Power Module, 60V, 20A, 300W
N6754A
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
DC to DC Voltage Regulator
HVDR-15
-
The HVDR-15 is a high efficiency, high voltage step down DC to DC voltage regulator. Input voltage can be as high as 110VDC. Up to three output voltages can be pre-configured to allow up to 1A or 3A of output current. The HVDR-15 features over voltage, over current, and over temperature protection. It is offered in one, two, or three output voltage versions making it a very efficient and flexible platform for many applications.
-
Product
DC Hipot Test Set
KVZG
-
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
Product
Medium Capacity Single Point Bending Beam Load Cells
SPL SERIES
-
The SPL Series single point load cell simplifies scale designs, packaging machinery and other industrial weighing equipment. Their single point design eliminates the need for multiple load cells and summing boxes, and thus, simplifies the design and reduces the cost. All SPL Series load cells employ 100% aluminum construction and features a moisture proof sealant which also makes them suitable for damp environments.
-
Product
Single Channel Linear DC Power Supply
MPS-D+ series
-
Voltage stabilitySource effect CV≤0.01%+2mVLoad effect CV≤0.01%+2mVRipple and noise CV≤1mV(rms）CC≤5mA(rms）Voltage temperature coefficient 150ppm/°CCurrent stabilitySource effect CC≤0.2%+2mALoad effect CC≤0.2%+5mACurrent temperature coefficient 500ppm/°C
-
Product
DC Power Supply, 100 V, 0.4 A, 40 W
E36106B
DC Power Supply
The Keysight E36106B is an accurate, 100 V, 0.4 A, 40 W compact power supply for your bench or system.
