Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
Product
Digital Tachometer
RM-1500 /RM-1501
-
5 Digits LCD Display. Light Reflex Measurement. Range from 10.00 to 99,999 RPM. Measuring Distance 50 to 300 mm. Event Counter elapsed time. Max/Min/Hold : True Average
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX3032T
Oscilloscope
350 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
FLIM Upgrades for Zeiss LSM
710 / 780 / 880
-
*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Detection Wavelength Range from 360 nm to 900 nm*Excitation by Ti:Sa Laser, OPO, or by bh ps Diode Lasers*Identical Systems for Multiphoton FLIM and Confocal FLIM*Detectors can be Swapped Between NDD Port and Confocal Port*Systems are Modular: More FLIM Channels can be Added
-
Product
Digital Relay and Merging Unit Tester
POM2-3333
-
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
Product
Ozone Meters
-
In this section you will find an ozone meter to determine the content of ozone in the air or in the water. The ozone meter is essentially used in environmental technology, but the ozone meter is also used in industrial processes. The ozone meter in water is necessary for water treatment or recycling facilities, such as disinfection processes. The handling of the ozone meter is very simple. The recalibration of the ozone meter can be made by the user at any time. The ozone meter in air requires a more complicated calibration, usually a sensor works for two years with optimal results (little variation) before having to be changed.
-
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Duty Cycle Meter
-
Displays ON or OFF period as a percentage of total period over a programmed gate time from 10 ms to 199.99 s. A resolution of 1%, 0.1% or 0.01% is user-selectable. Applications include monitoring modulated proportional control systems and pulse-modulated systems, such as radar, lasers or packet radio.
-
Product
6 GHz Programmable Delay Line
PADL6
-
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
Product
Boundary-Scan Test Executive
ScanExpress Runner
-
Efficiency in engineering means managing your most precious resources: time and effort. Automated testing is essential and boundary-scan is a critical component; no other structural test system provides the same value.When down to the wire, your boundary-scan test system needs to be built both for ease-of-use and reliability; a robust and powerful mechanism to ensure that no matter the state of production, all boundary-scan tests can be quickly and faithfully executed to maintain forward momentum.
-
Product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Werklicht® Pro S
-
brings the dynamic laser projection directly into the production line. Bring digital work instructions in the correct position on the moving component. WERKLICHT® Pro S has been consistently designed for multi-projector installations that are permanently integrated into the production line or production cell. Through the synchronous operation of a freely configurable number of modular projection units, all relevant areas can be covered in the network. The complex scalable solution thus meets the special requirements of extremely short cycle times.
-
Product
Programmable High Power DC Power Supply
ADG series
-
Preen’s ADG series is a programmable DC power supply with high power density and high output power, and offers many great advantages on response time, accuracy and output voltage range. ADG is an excellent source for testing or facility type applications, such as aerospace, renewable energy, automated test system, battery and server. With power level up to 80kW per unit, the ADG series provides output voltage up to 1000V and high output current of 2000A after custom modification.
-
Product
Line Scan Detectors
-
a machine vision device that captures images one row of pixels at a time, rather than a full frame at once.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781262-01
Vector Signal Generator
PXI Vector Signal Generators offer custom and standard modulation, as well as the ability to generate communications standards formats such as GPS, WCDMA, DVB-H, and more. They support quadrature digital upconversion, which reduces waveform download and signal generation time, as well as stream-to-disk capabilities. The power and flexibility of PXI Vector Signal Generators make them ideal for use in scientific research, communications, consumer electronics, aerospace/defense, and semiconductor test applications as well as for areas such as software-defined radio, radio-frequency identification (RFID), and wireless sensor networks.
-
Product
Dynamic Signal Analysis
-
m+p Analyzer is a fully integrated solution for dynamic signal measurement, analysis and advanced reporting of all noise and vibration, acoustics and general dynamic signal applications. Comprehensive time and frequency analysis is available with both online and offline data processing. Complete with advanced application wizards the m+p dynamic signal analyzer makes light work of gathering data, displaying results, performing specialized analysis and generating customer ready reports – all within one user interface. m+p Analyzer is designed for noise and vibration applications in the field and in the lab.
-
Product
Xineos Scanning
-
Teledyne DALSA's leadership in CMOS innovation lets our Xineos scanning products deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.
-
Product
PXIe-6357, 208 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO PXI Multifunction I/O Module
790595-01
Multifunction I/O
The PXIe-6357 offers analog I/O, digital I/O, and four 32-bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6357 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
MIL-STD-1553 VXI Module
QVXI2-1553X
-
The QVXI-1553X provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on a C-size card. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the QVXI-1553X includes "abstract" API (Application Programming Interface) software that reduces application development time.
-
Product
Surface Insulation Resistance Testing
AutoSIR2™
-
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
Product
Space Power Solutions
-
Teledyne e2v HiRel Electronics (HiRel) offers leading edge power solutions dedicated for high-reliability applications. The introduction of Galium Nitride (GaN) technology solutions enable high power density designs with four times less space requirements than traditional MOSFETs. The Teledyne HiRel Point-of-Load (POL) products combine multiple load capabilities, outstanding radiation performance with high levels of integration and easy to use features.
-
Product
Eclipse Test Development Environment
-
The Eclipse Test Development Environment automatically creates tests that are used to bring up new products in the lab. Failures can be quickly debugged using software tools such as the Eclipse Timing Diagram Analyzer and the Schematic Logic Probe.
-
Product
50Hz-100kHz LCR Meter
11022/11025
-
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
Product
Vibration Testers
-
Guangzhou Amittari Instruments Co.Ltd
The Vibration Tester can display the parameters of “Displacement”, “Velocity” and “Acceleration” simultaneously; Applied to the periodic motion measurements to detect moving mechanical imbalances and misaligned. Designed for on-site measuring various mechanical vibration, for quality control, running time and prior equipment maintenance data. Selection of high-performance accelerometers to achieve accurate, replicable measurement It has a bearing condition measurement function.
-
Product
Process Analytical Technology
-
Pharmaceutical manufacturers are facing an increased regulatory emphasis on real time evaluation of materials during production. Process Analytical Technology (PAT) – an U.S. FDA initiative – is creating the need for new tools that can provide on-line quality measurements to ensure stringent consistency and performance standards are met.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A12
-
IR Carbon and Sulphur Analyzer LCSA–A12 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and 10 to 30 °C, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 32-bit sampling improves sensitivity and accuracy.
-
Product
Static Pressure Manometer Kit
EM201SPKIT
-
UEi Test & Measurement Instruments
A digital, time saving electronic manometer static pressure kit
-
Product
Indoor Gunshot Detection And Response System
Pre-SenseShot
-
Information System Technologies Inc.
ISTI offers a new detection system to the facility security and safety industry to quickly neutralize an active shooter and more quickly secure and protect occupants. When confronted with an active shooter situation first responders and safety personnel face immediate tactical disadvantages. Beyond rushing towards ensuing chaos, 9-1-1 calls and eye witness reports are often disjointed, inaccurate, and lack precise location information required to make real time responsive decisions as they arrive on scene. Likewise within the building, the crisis triggers panic and chaotic scrambles towards exits and assumed safe havens. However unorganized and uniformed retreats may actually be leading evacuees back into harm’s way.
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
LED Sensor
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
