Phase
the difference between two features of a waveform, measured in any of multiple manners (distance, time, angle, wavelength, etc.)
See Also: Phasing, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Time
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Phase Locked Laser System
SolsTiS-Phase Locked
-
The phase locked SolsTiS system is primarily designed for use in atom interferometry and quantum computing where Raman transitions are commonly used, although we can tailor the setup to other applications. The system provides extremely low phase noise and high output powers. Full control over the system is provided through our easy to use Ice Bloc user interface.
-
Product
Power Phase Converter Single phase 220VAC to 3 phase 380VAC Converter
SDT-40KW
-
Zhejiang Sandi Electric Co., Ltd
SANDI SDT series single-phase to three-phase converter, adopted SVPWM modulation control technology, which can convert ordinary single-phase power to industrial three-phase power. After through SDT series single-phase to three phase converter power conversion, the three-phase power output is standard pure sine wave, the harmonic distortion rate (THD) is less than 2%, totally meet the national standards of three-phase power quality, applicable to all types of load.
-
Product
Source Phase Control
S95088B
-
The S95088B allows users to set calibrated, arbitrary phase differences between two signal sources on the M980xA PXI VNAs.
-
Product
AC-Powered, Phase Sequence Monitor
PAA/PLA
-
NAI's PAA and PLA are AC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
Phase Verification Bridges
5002
-
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
Product
Low Phase Noise Frequency Synthesizer
-
Corech’s low phase noise frequency synthesizer series generates precise and stable frequency signals across a wide frequency range, available in SPI serial interface. These cost competitive, rugged and compact module are the ideal choice for RF & Microwave systems such as communication systems, test and measurement equipment, radar systems etc.
-
Product
Phase Sequence Tester
TKF-12
-
The TKF-12 tester is a modern high-quality, simple and safe device. However it is recommended to get acquainted with he present manual in order to avoid measuring errors and prevent possible problems related to operation of the meter.
-
-
Product
Mechanical Tunable Phase Shifters
-
The phase shifter features a high resolution precision micrometer which allows for finer adjustment sensitivity than a standard micrometer. The phase shifter is an ideal piece of equipment in waveguide systems where broadband phase shifting is required. The phase shifter exhibits a 2.5 dB typical insertion loss and an adjustable phase range of up to 180 degrees.
-
Product
Phase Detector Modulevalon
4002
-
sThe Valon 4002 Phase Detector module Independently measures both Gain/Loss and Phase between two signals. It is a perfect complement to all our Frequency Synthesizer modules and ideal for many experimental RF applications. The 4002 enhances the performance of the AD8302 base core.
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
3 Phase/ Motor Rotation Tester
-
Phase rotation indication by both audio and indicator, checking if currents of three different rating are in proper phase. Phase open-circuit detection by indicator.
-
Product
Three Phase Power Monitoring
-
PRÜFTECHNIK Condition Monitoring GmbH
A three-phase power monitor detects changes in electrical variables. With power monitoring on your assets, you can help reduce wear and damage, while also identifying what’s causing it. The Fluke 3540 FC three-phase power monitor can be used remotely or through a stationary connection.
-
Product
Phase Rotation Tester with Voltmeter
885 PR
-
Standard Electric Works Co., Ltd
● 3 functions in one unit: Phase Rotation, Phase Presence, Voltmeter● LCD contact type Phase Rotation Tester● Large LCD to show phase rotation and phase presence● Check a wide range of three phase power sources● Voltage range for phase rotation test: 75~600V AC ● Frequency range: 40~400Hz● 6000-count voltmeter● Auto ranging Voltmeter AC/DC● Data hold function● Auto power off● Convenient stand for viewing● Easy to use● Comply with EN 61010-1 CAT III 600V EN 61010-2-033 EN 61326-1
-
Product
DIGITAL PHASE ANGLE METER
GF211B
-
Beijing GFUVE Electronics Co.,Ltd.
GF211B onsite handheld digital phase angle meter can measure alternating voltage, alternating current, frequency, phase angle, active/reactive power, power factor and so on.
-
Product
Phase Angle and Power Factor Transducer of Single-phase AC Electric Power
NMTFi
-
The NMTFi device is a phase angle and power factor transducer operated in single-phase power network and featuring two independent analogous outputs. The A output measures the phase angle between voltage and current, the B output measures the power factor. In such a was one single NMFTi transducer is able to replace two customary transducers thus making it possible to achieve significant savings in installation space.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
-
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
Three Phase Reference Standard Meter
-
Signals & Systems India Private Limited
The Three Phase Reference Standard Meter (TPRS-1107) is portable equipment from SANDS. The main objective of this device is to calibrate the errors in three-phase and single-phase energy meters i.e. the meter under test (MUT). The TPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, power factor etc of the meter under test. It has an LCD display, an alphanumeric keypad that makes it easy for the user to operate the TPRS. It can be interfaced with the PC for data analysis. It has the capability of storing up to 8000 test results.
-
Product
3 Phase Power Monitors
-
The PM7000 portable monitor, the PM7503 panel mounted monitor and the PM7000 Fault Level Monitor have 4 current inputs and 4 voltage inputs while the PM3000 portable monitor has 3 current and 3 voltage inputs. All 4 different models record data using our patented Single Cycle Adaptive Store recording regime whereas the PM7000, PM7503 and PM7000FLM also have 3 other unique and distinct recording regimes:
-
Product
Single Phase Relay Testing
-
Megger’s single phase relay test sets are essential items in the relay engineer’s toolbox. Lightweight, rugged with high compliance voltage and test current. Ideal for testing distribution networks, industrial relays, distance relays in rail power networks and many other applications.
-
Product
Single Phase Relay Tester
PTE-50-CE Pro
-
This electronic, independent source can be adjusted in amplitude, frequency, and phase angle. It comes installed as standard with the ‘Pro’ versions of the PTE sets, but it can also be purchased separately and mounted by the user inside the unit’s lid in a few minutes.
-
Product
Two Phase AC Motor Drive
MS 2014
-
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
-
Product
Phase Sequence Indicator
PHS 863
-
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
Product
Phase Noise Tester 5MHz to 40GHz
Model 7340
-
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
Three Phase Load Bank
REOLOAD 310
-
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
-
Product
Phase Shifters
-
Essential function blocks such as Teledyne RF & Microwave Phase Shifters provide reliable, high performance for RF/Microwave commercial, industrial and military systems.
