Programmable DC Electronic Loads
Vary load current programmaticlly.
-
Product
Programmable High-Current
Copperhead
-
AMETEK Programmable Power, Inc.
Provides 15,000A DC at 5V DC in current mode*Single complete package*Integrated bus bars*Current mode Analog programming*Input 400VAC, 220A/ph, Delta
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 3.55k
40-297-023
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Radar Electronic Support Receiver
RR024
-
The RR024 is designed for Radar Electronic Support (RES) and Radar Warning Receiver (RWR) applications where high performance and small size are of prime importance, with filtering, amplification, detection and pulse parameter measurement being combined into one multi-function unit. Four amplitude measurement channels allow direction finding by amplitude comparison between adjacent antennas. An IFM, fed from one of the amplitude channels via an SPDT switch, performs 14 bits of frequency measurement on the selected input. Frequency resolution is nominally 1 MHz over a 2 to 18 GHz band.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
48V / 200 Amp Load
EL12-48M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely costeffective.
-
Product
Power Electronics Test Bench
OP1300
-
The multi-purpose and ready-to-use Power Electronics Test Bench combines a state-of-the-art Hardware-in-the-Loop (HIL) simulator from OPAL-RT with Imperix’s Rapid Control Prototyping (RCP) system and real power hardware. It enables rapid development of power electronics, drives and smart-grid applications across industry and academia.
-
Product
DC Power Supplies
ASD FLX Series
-
AMETEK Programmable Power, Inc.
The ASD FLX gets its name from its modular design with front loading modules for easy access and flexible voltage options. The chassis with removable, lightweight modules allows for easy one person installation. Furthermore, this product has a wide range of voltage input, 324 VAC to 528 VAC, giving it the flexibility to be utilized globally in a single configuration.
-
Product
Economical Bending Beam Load Cells
EBB SERIES
-
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
Product
Programmable AC Power Source
-
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
Product
Unclamped Inductive Load Tester
ITC55100C
-
The system has been designed around a very powerful micro-controller that gives it a timing resolution of 40ns, twenty times faster than the previous model. Its response time to the peak and zero current is improved ten times. Combined this gives greater accuracy for the charging and avalanche times and for the reported peak drain current.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Power Electronics Test Solutions
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-031
Programmable Resistor Module
The 40-297A-031 (PXI) and the 42-297A-031 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Load Test Software
TW-3.0
-
The TW-3.0 Load Test software from DLM is a software platform designed to complementDLM’s TW-3.0 range of products within the lifting industry. Used as a tool for assisting therecording of test results and generation of certificates during a load test, the software is able to be loaded onto a Windows PC and accept the output from a TW-3.0 handheld display.
-
Product
6kW Regenerative DC Electronic Load (CC/CR/CV/CP/CC+CV/CR+CV)
PLZ6000R
-
PLZ6000R is a DC electronic load that regenerates load power to the AC line. Regular electronic loads consume load power by having semiconductor devices convert it into heat. By contrast, PLZ6000R converts load power into reusable electric power, rather than converting it into heat as is typically done, and feeds this power to the AC line, thereby substantially reducing the amount of waste energy. PLZ6000R is an environment-friendly electronic load that can contribute significantly to your energy saving efforts.
-
Product
DC Coupled Current Probe
34134A
High Current Probe
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
-
Product
Universal Function Test System for Industrial Electronics
Test System
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
Product
DC Power Products
-
West Mountain Radio offers a variety of power management devices to protect both the radio equipment and the power systems they are connected to. These devices provide both battery charge management and load management features. They are for public safety, commercial, marine and amateur radio applications. All products designed and tested by Ham radio operators.
-
Product
Full Load Testing For Self Priming Pumps With Pneumatic System For Loading & Unloading Of Pumps
-
Aarohi Embedded Systems Pvt. Ltd
While manufacturing of self priming pumps testing time is very important to avoid bottleneck. Aarohi developed semi automatic performance testing system with pneumatic system for loading & unloading of pumps which helps to enhance productivity & work efficiency.
-
Product
Brushless DC Motor Drivers
-
ST’s STSPIN drivers for 3-phase brushless DC (BLDC) motors includes power drivers in a 3-phase bridge configuration and integrated solutions with built-in decoding logic for Hall-effect sensors.
-
Product
DC Power Supplies
-
Single, dual or triple output models with power from 30 watts up to 1200 watts. Linear, Mixed-mode or PowerFlex regulation. Remote control models with variants of Analog, USB, RS232, GPIB and LAN interfaces.
-
Product
Loading Adjustable Drop Tester Machine
CX-DL15A
-
Shenzhen Chuangxin Instruments Co., Ltd.
Package Impact Drop Testing Machine is used to measure the dropping impact incidence when the package in using, transportation and decorating. Labtone "1G+" project strictly ensure the accuracy. Besides precision plane drop testing, it also can undertake edge and angle test to ensure the complete performance evaluation for the package. During the products handling or transport process, there may be drop/ fall, which results in damage within the products. And this Drop Tester simulates the drop/ fall of a finished product to evaluate the damage. All the rhombohedrons, angles and faces of the products can be tested.
-
Product
Electronic Ballast Tester
WT5000
-
WT5000 is the updated version of WT3000 with a super LCD for displaying waveforms and parameters directly, and it includes all the functions and technical parameters of WT3000. Reports can be printed if printer is connected. It also meets the latest requirements for electronic ballasts in international standards IEC 60929, IEC 60969, IEC 61000-3-2, GB/T15144-2005, GB/T17263-1998 and so on.
-
Product
460V / 18 Amp Load
EL08-460M
-
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 307V to 460V and is extremely cost effective.
-
Product
DC Power Supplies
XG 1700
-
AMETEK Programmable Power, Inc.
The XG 1700 is an industry leading programmable DC power supply designed for test, production, laboratory, OEM and quality assurance applications. The XG 1700 is a 1700 Watt, 1U programmable power supply with constant voltage and constant current modes, automatic cross-over and numerous features enabling cost effective, easy integration.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 102kΩ
40-251-034
Programmable Resistor Module
The 40-251-034 is a programmable resistor module with 4 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Load Cells for Weighing
-
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
Product
Programmable Delay Line Instrument
XT-200
-
Built using the same technology that made Colby a trusted name, today the XT-200 stands as our flagship product. The XT-200 utilizes not one but two of Colby's patented trombone to offer precise programmable delay or phase shift for dual-channel requirements.
