Programmable Attenuators
-
Product
Wide-range Programmable DC Power Supply
IT6900A Series
-
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
Product
Controllable, Programmable DC Source
LAB SMP
-
*Easiest operation via the front panel*Indication via graphic display*Constant current, voltage, resistance, power operation and simulation of PV characteristics*Creation of any voltage and current curves via memory card or digital interface (sequential control)*Voltage and current rise time (U and I slope) adjustable*Umax and Imax can be set by the user in order to limit the output voltage or current
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
Product
Programmable DC Electronic Load
IT8500+ Series
-
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications. They can be offered as multiple solutions according to customer's design and testing requirements.
-
Product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
Programmable Resistor Module
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 773k
40-297-043
Programmable Resistor Module
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-036
Programmable Resistor Module
The 40-254-036 (PXI) and 42-254-036 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 395kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PCI 18 Channel Precision Resistor Card
50-297-001
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Programmable Parametic Tester
IST 878
-
IST Information Scan Technology, Inc.
The IST 878 is a low cost test instrument that provides in-circuit or out-circuit testing for a wide range of discrete semiconductors
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 201kΩ
50-298-141
Programmable Resistor Module
The 50-298-141 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 201kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Millimeter-wave and Microwave GaAs Attenuators
-
Keysight Technologies provides MMIC attenuators ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
Product
Universal Programmer Superpro 7500
-
Until now,Support 396 IC manufacturer, 94596 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V. The programming speed up further increase 30% compared to SUPERPRO 5000.The programmer support files up to 256 GBytesBuilt with 144 universal pin-drivers.Universal adaptors are available for varies packages up to 144 pins. New device support will be easier. PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via the 6-KEY keypad and the 20 character by 4 line LCD display. A SD card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-043
Programmable Resistor Module
The 40-297A-043 (PXI) and the 42-297A-043 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 773 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-130
Programmable Resistor Module
The 40-297A-130 (PXI) and the 42-297A-130 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 6.97 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-252-011
Programmable Resistor Module
The 40-252-011 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Programmable DC Electronic Loads
SDL1000X/X-E Series
-
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
Product
Programmable DC Electronic Load
DL3000
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics and fuel cells.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 1.51MΩ
40-251-150
Programmable Resistor Module
The 40-251-150 is a programmable resistor module with 1 channel which can be set between 3Ω and 1.51MΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Programmer
Gang2000
-
The GANG2000 Programmer is a multi-tap device that can quickly and efficiently program multiple independent target boards that use the Texas Instruments C2000 32-bit Microcontrollers from a Windows PC over a high-speed USB2.0 port. You can also use the Gang2000 during program development as a JTAG emulator.
-
Product
PXI Resistor Module 4-Channel 1R to 510R
40-293-014
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
-
Product
Attenuator
RFATT AXIe-0
-
*Dual channel AXIe attenuator with frequency range from 9 kHz to 10 GHz.*The module is designed to work as part of information measuring systems as a normalizer of radio frequency signals (power control: signal amplification or attenuation).
-
Product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
-
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
Product
Programmable Automation Controllers
-
Amplicon offers a broad range of programmable automation controllers (PACs) that can be deployed in a variety of industries. All support a broad range of automation and control protocols such as, Modbus TCP, Modbus RTU/ASCII, PROFIBUS, PROFINET, EtherNET/IP, EtherCAT and CAN bus. We have the technology capable of controlling simple edge processes through to complex automation applications across all industrial, infrastructure and building sectors.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 11.4MΩ
50-297-053
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable High Voltage Tester
-
The high Voltage also known as di-electric withstand tester comes with customized facilities like voltage rampup rate zero interlock, Plus the user may specify the voltage level and leakage milliampere level so as to suit its testing needs.
-
Product
150-Watt AC/DC Power Supply; Dual Output
56MD1
Programmable Power Supply
NAI’s 56MD1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, dual output, at a baseplate temperature of +85° C.
-
Product
PC Programmable, Suitable For Pt100 Sensors
SEM206P
-
The SEM206/P is our entry level PC programmable temperature transmitter. It accepts Pt100 temperature sensors and converts the sensor output to a standard industrial (4 to 20) mA transmission signal.
-
