Programmable Attenuators
-
Product
PCI High Density Pecision Resistor Card
50-298-131
Programmable Resistor Module
The 50-298-131 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Programmable High-Current
Copperhead
-
AMETEK Programmable Power, Inc.
Provides 15,000A DC at 5V DC in current mode*Single complete package*Integrated bus bars*Current mode Analog programming*Input 400VAC, 220A/ph, Delta
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 3.55k
40-297-023
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Attenuator Banks
-
HYTEM offer different RF attenuation systems that allow to perfom simultaneous types of tests on multiple RF links (handover for instance). Multiple configurations are available : Standard, MIMO, Link separation, Spécific.
-
Product
Fixed Attenuator (Waveguide)
-
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
Product
Manual Attenuator (Coaxial)
-
Manual control coaxial attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
Product
Programmable AC Power Source
-
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-031
Programmable Resistor Module
The 40-297A-031 (PXI) and the 42-297A-031 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Programmable Delay Line Instrument
XT-200
-
Built using the same technology that made Colby a trusted name, today the XT-200 stands as our flagship product. The XT-200 utilizes not one but two of Colby's patented trombone to offer precise programmable delay or phase shift for dual-channel requirements.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 102kΩ
40-251-034
Programmable Resistor Module
The 40-251-034 is a programmable resistor module with 4 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 13.6kΩ
40-253-031
Programmable Resistor Module
The 40-253-031 is a programmable resistor module with 1 channel which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 122Ω
40-298-012
Programmable Resistor Module
The 40-298-012 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Attenuators
-
An attenuator is an electronic device that reduces the power of a signal without appreciably distorting its waveform.
-
Product
Programmable DC Power Supply
KM-LPP-3030T
-
Kusam Electrical Industries Limited
KM-LPP-3030T provides a higher stability in terms of traditional Programmable DC Power Supply. KM-LPP-3030T, linear programmable DC Power Supply support USB PC-Link and two completely separate power outputs. With the various characteristics, KM-LPP-3030T is the best choice of power supplies for engineers. With the functions of the power supply of KM-LPP-3030T, it provides two completely separate power output which is able for series or parallel connection; other than the common power supplies on the market of positive / ground / negative output. In addition, KM-LPP-3030T supports low-voltage digital circuits, also it is able to switch voltage among 1.8V~5.0V. With its characteristics of stability and high - speed reaction, KM-LPP-3030T provides high quality at a very economical price.
-
-
Product
Programmable Micro-Ohmmeter
4300C
-
The 4300C is the perfect instrument for tackling ultra-low resistance testing requirements associated with motors, transformers, fuses, connectors, breakers, bonding/weld resistance, and many other applications. The 4300C Digital Micro-Ohmmeter measures a variety of low-resistance devices ranging in value from 100nΩ to 20kΩ. The flexible measurement format of the 4300C provides six ranges of user selectable test current (from 0.1mA to 10A) and three voltage sensitivity settings (20mV, 200mV, and 2V).
-
Product
Programmable Electronic Loads
SFL Series
-
The SFL DC Electronic Load Series is a multi-functional programmable DC Electronic Load series that offers power levels of 300W (3U Half-Rack) and 1kW (3U Full-Rack) with high-speed current control (no dynamic overshoot/oscillation), high slew-rate (up to 30A/us) and stable operation at low voltage with no turn-On delay. It is lightweight and has a user-friendly front panel with built-in (USB) and optional (IEEE) communication Interfaces.
-
Product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Fixed Attenuator
FAXE
-
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
Product
Programmer Memories VP-598
-
Support more than 21 637+ memories . We are official distributor of Wellon products in Poland. Our customers receive 3 years warranty and 72h support.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-155
Precision Resistor Module
The 40-297A-155 (PXI) and the 42-297A-155 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
Tiny AVR Programmer
-
The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
Programmable Resistor Module
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
High-Precision Programmable DC Power Supply
MPS-3600H Series
-
MPS-3600 HSeries is a new generation of high-precision programmable DC power supply. This series of products is equipped with a standard communication interface, which has both desktop and system characteristics. It can be arbitrarily matched with other instruments and integrated into a special function test system to complete the measurement requirements in different occasions.
-
Product
VVDI Programmer
-
MC9S08 series secured and unsecured , MC68 HC series (9) 12 secured and unsecured, MC9S12 series secured and unsecuredV850 series, H8X series, R8C series, R5F series, PCF79XX, EEPROM SPI, I2C, & mu WIRE, PIC 12F, 16F, 18F, Infineon TRICORE, Infineon XC2xxxx, Infineon XC164CS, ST10F series, ST7 series, STM8 series, ATMEL- Atmega 8, 48, 16, 32, 64, 128, 256, MPC560 series, SPC560 series, Fujitsu MB91F
-
Product
PCI Precision Resistor Card 9-Channel, 1Ω To 122Ω
50-297-112
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-016
Precision Resistor Module
The 40-297A-016 (PXI) and the 42-297A-016 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 1.8 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
ISP Programmer Superpro Is01
-
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
