Loop Impedance Test
See Also: Impedance Testers
-
Product
Flying Prober Test System
QTOUCH1404C
Test System
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
test
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
RCD Loop Line
-
Digital measuring instrument for RCD testing with Loop and Line resistance measurement also without tripping the RCD.
-
Product
Single Loop Controller
1462
-
The N4400 is a sophisticated, single loop controller which provides extensive profiling programming options for complex processes. The controller can create a profile with up to 121 segments, store up to 8 programs and configure and store extra programs on a PC.
-
Product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
-
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
Impedance meters
-
Electronic components meters for circuit verification in laboratories, technical schools and technical support centres.
-
Product
Precision Impedance Analyzer (20Hz to 10MHz)
ST2839
-
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Product
Photonics Module Test System
58625
Test System
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
Product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
Test Platform
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
Product
Audio Impedance Testers
1106 IM
-
Standard Electric Works Co., Ltd
Large LCD : 68 × 34mm (2.677" × 1.338"). True measurement of speaker systems actural impedance at 1kHz. Three test ranges allow testing of home theater and commercial sound systems. Measures transformer impedances. Battery operation. Low battery indication. Data hold function. 0Ω adjustment.
-
Product
System for Determination of Materials Impedance in Impedance Tubes
-
System for determination of materials impedance in impedance tubes is used for evaluation of material’s acoustic properties.
-
Product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
-
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
Product
LCR Meters & Impedance Measurement Products
LCR Meter
Hewlett Packard, Agilent and Keysight have contributed innovations and product excellence in impedance analysis for over half a century. Whether your application is in R&D, production, quality assurance, or incoming inspection, we take pride in contributing to your success. We strive to deliver complete solutions to meet your needs, from impedance analyzers to a wide variety of test accessories. Achieve success with Keysight’s impedance measurement solutions.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Closed Loop Precise Hall AC/DC Current Sensor
CYHCS-LF
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for accurate measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Impedance Matching Pads
-
Impedance matching pads from BroadWave eliminate impedance discontinuity (mismatches) without introducing reflection to the circuit. Custom units are available in a variety of impedance and connector types from DC to 4 GHz. BroadWave Technologies impedance matching pads preserve signal integrity by matching virtually any transmission line.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
Loop Tack Tester
-
Loop Tack Tester is applicable to measure the tack property of adhesive tapes, pressure-sensitive adhesives (PSA), and adhesive materials according to ASTM D6195.
-
Product
Impedance Meter, Audio, 200Ω, 2KΩ and 20KΩ scales
72-6948
-
Active device is essential for reliable installation of background music and paging systems in residences, offices buildings and public areas. Avoid costly service calls and amplifier damage by verifying actual speaker system impedance prior to operation. Unlike conventional volt/ohm meters, which measure DC resistance, this unit utilizes an internal 1KHz oscillator to measure true impedance. Accurately measure speaker lines that utilize impedance matching volume controls, switchers, transformers and passive crossovers. Because this unit accurately measures up to 20Kohm, it may also be utilized with 25V, 50V, 70V, and 100V speaker line transformers in commercial installations.
-
Product
Function Test and In-Circuit Test
CT350
-
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
Product
Test Sockets
-
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available
-
Product
Microwave Testing
120
-
The MODEL 120 PICOPROBE® sets new standards in microwave probing performance. Benefiting from coaxial techniques, which have inherent low loss and low dispersion characteristics, the Model 120 Picoprobe®, achieves an insertion loss of less than 1.75 db (typical) and a return loss of greater than 15 db (max.) over its frequency range.
-
Product
4-20mA Current Loop D/A Converters
-
ADI integrated solutions combine both the D/A converter and driver in one chip to provide the required output directly from the digital domain. Analog Devices’ portfolio of leading industrial D/A converters and drivers provides a range of programmable output ranges from standard 4 mA to 20 mA for current loop communication to ±10 V for actuator control. ADI industrial converters offer considerable control functionality and advanced on-chip diagnostics to maximize system uptime, as well as eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
Motor Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's Motor Test Systems come fully equipped with the latest industry features based on your testing needs. The on-screen display in our testers make it easy to read, track, and record your motor information during the testing process. We realize this importance and want to make sure you never have to worry about losing key information ever again. Performance and reliability are important, so we make sure you will have full confidence of every motor you test, whether you place it in your product or send out the door to your customer. ESW's design team works closely with you to determine the tests you need, in order to make a system that will meet all your testing needs. See the slideshow below to see some of our Motor Testers.
-
Product
Impedance Meter
ZM-100
-
Monacor International GmbH & Co.
Impedance meter for measuring the impedance (Z) of individual loudspeakers and loudspeaker lines.
-
Product
Memory Test System
T5230
Test System
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Test Switches
Series FT
-
An industry standard for CT & VT isolationfor instrument transformer and connected device testing.Up to 10 poles; Numerous configurations availableTypically mounted on switchgear and relay panels10 pole test plug available; UL and cUL recognized.
