Filter Results By:
Products
Applications
Manufacturers
Breaker Test Systems
-
product
Circuit Breaker Test Systems
Crest has over a decade of experience of designing and manufacturing test systems for testing all the different kinds of switchgear and controlgear.
-
product
Automatic Circuit Breaker Test Systems
UPA-16 (UPA-20)
Mobile systems for primary injection testing and trip curve control of circuit breakers and overcurrent protection relays.
-
product
Circuit Breaker Testing Equipment
CB SCOPE
SCOPE introduces CB SCOPE – Loco Vaccum Circuit Breaker Test System; the ultimate solution for testing Loco Circuit Breakers of all types. CB SCOPE is the most complete analyzer for checking the dynamic performance of LOCO VCB’s.
-
product
Circuit Breaker Test System
TDR9100
The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.
-
product
Automatic Circuit Breaker Test Systems
UPA-1 (UPA-3)
These portable systems for primary injection testing of circuit breakers which are used in in AC circuits of industrial frequency.
-
product
Circuit Breaker Test System
TDR900
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
product
Circuit Breaker Test System
AutoScan
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
product
Stationary Circuit Breaker Test System
ACTAS C160
Stationary test system for carrying out fully automatic final factory tests, type and function tests on all kinds of switchgear devices, such as circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit. All the electrical and mechanical parameters needed for the assessment of switching performance are measured in real time and evaluated without either the main contact chambers or the drive unit having to be opened. The system has analog and incremental input channels for the acquisition of analog quantities.
-
product
Advanced SoC/Analog Test System
3650-EX
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
product
CPE Design Verification System
Jupiter 310
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
product
Mixed Signal Battery Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
product
Photonics Wafer Probing Test System
58635
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
-
product
Benchtop Communication Test System
ATS3000A
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Advanced SoC/Analog Test System
3650
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
product
NI Vehicle Radar Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
product
Component Test Systems
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Regenerative Battery Pack Test System
17020E
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
product
Semiconductor Test Software
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
product
VLSI Test System
3380D
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
product
In-Circuit Tester
Sparrow MTS 30
The Sparrow MTS 30 is a 19“ test system that can be integrated into any standard rack. The In-Circuit tester can also be used as benchtop test system. With this compact and flexible tester you can perform both analog and digital In-Circuit and functional tests.
-
product
Communications Test System for Frontline Diagnostics
CTS-2750
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
-
product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
Systems Integration (SIL) Lab Data Acquisition
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
