POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
Product
ABex Terminal Module for NI 407x and 408x DMM Cards
ABex TM-4070 DMM
-
The ABex TM-4070 is an ABex terminal module to interface with NI PXI-407x or PXIe-408x and gives the possibility to rout the DMM signals to the front connector and the Analog bus. The routing to the analog bus is software controlled and the signals are switched with reed relays.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card
50-298-024
Programmable Resistor Module
The 50-298-024 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI 16x8 2Amp High Density Matrix Card
50-529-001
Matrix Switch Module
The 50-527, 50-528 and 50-529 are a range of PCI single pole matrix cards supporting either 64 or 128 crosspoints using electro-mechanical relays. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A.
-
Product
Centralized Motion Control Card
-
Centralized motion control solutions include 4-axis, 6-axis, 8-axis motion control cards and embedded motion controller, utilizing a high-performance DSP to calculate the motion trajectories and FPGA to process critical motionI/O. The kernel on DSP is the one of SoftMotion built by Advantech. All motion control PCI cards support common motion API for easy integration or machine upgrade.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
-
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
Product
PCI 50xDPST Reed Relay Card
50-115A-122
Reed Relay
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
12-Bit, 4-Ch Analog Output PCI Card With 16-Ch Digital I/O
PCI-1721
Analog Output Card
10 MHz maximum digital update rateSynchronized output function16-ch DI/O and one 10 MHz 16-bit resolution counterFour analog output channels with 1,024 samples FIFO bufferA 12-bit DAC is equipped for each of analog output channelsReal-time waveform output function with internal/external pacerFlexible output types and range settingsKeeps the output settings and values after system hot resetAuto calibration functionBoardID™ switch
-
Product
Card type, Mini Wireless Camera Detector, with vibration
SH-005V / 10127
-
This "Card type Mini Wireless Camera Detector / Hidden Camera Detector" is special made for detecting all kinds of wireless spy camera, but insensitive to mobile phone signal that leads user a peaceful mind without panic.
-
Product
High Density Switching PXI Card
GX6338
Switch Module
The GX6338 is a low cost 6U switching card with 114 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6338 is ideal for applications requiring high density switching.
-
Product
OC-3/STM-1 And OC-12/STM-4 Analysis And Emulation Card(w/ GigE And USB 2.0)
LightSpeed1000™
-
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames. GL's LightSpeed1000™ hardware platform (PCIe Card and USB Pod) is capable of OC-3/12 and STM-1/4 wire-speed processing on quad optical ports for functions such as wire-speed recording and wire-speed playback of Unchannelized and Channelized ATM, PoS, and RAW Traffic.
-
Product
Ethernet FPGA Mezzanine Card
-
Sundance Multiprocessor Technology Ltd.
Quad Gigabit Ethernet FPGA Mezzanine Card that can be integrated with the EMC2.
-
Product
PCI Express Card
EXC-8000PCIe/xx
-
The EXC-8000PCIe/xx card for the PCI Express bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.
-
Product
4-Port MIPI Interface GMSL Video Capture Card
MIC-FG-4G
Interface
GMSL SerDes controller. Supports up to 4K, 30fps, quad channel. MIPI 4 Lane compliant. Power Over Coax. V4l2, Gstreamer, Python support on Linux.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
Analog Output Module
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
Product
Single Slot Intelligent Interface Card
IIB-3910-CPCI
-
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided in BC and RTs modes, with full error detection in BC, RT, BM and CBM modes. Dual redundant 3838 interface, with user selectable dual redundant optical or single redundant electrical 3910 interface are featured. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
500 KS/s, 12-Bit, 32-Ch Isolated Analog Input Universal PCI Card
PCI-1715U
PCI Card
2,500 VDC isolation protection32-ch single-ended or 16-ch differential or a combination of analog input12-bit resolution for A/D conversionProgrammable gain for each input channelSoftware, internal or external pacer sampling modes supportedOnboard FIFO memory: 1,024 samplesUniversal PCI busBoardID™ switch
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 1.81kΩ
50-298-122
Programmable Resistor Module
The 50-298-122 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
MIL-STD-1553 CompactPCI Interface Card
CPCIC3/6-1553-PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48 OUT
Controller
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
100 KS/s, 12-Bit, 32-Ch Isolated Analog Input Universal PCI Card
PCI-1713U
Isolated Digital Input Card
2,500 VDC isolation protection32-ch single-ended or 16-ch differential or a combination of analog input12-bit resolution for A/D conversionProgrammable gain for each input channelSoftware, internal or external pacer sampling modes supportedOnboard FIFO memory: 4,096 samples;Universal PCI busBoardID™ switch
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
Network Interface Card
NIC10G
Interface Card
Featuring the Intel 82599ES dual 10GbE controller, the NIC10G supports flow control, integrated IPsec security engines, optimized queues, IPv6 offloading, advanced filtering capabilities, and Tx/Rx IP, TCP and UDP checksum offloading capability. Also has integrated a PCI Express Gen 2 interface supporting up to 8 lanes.
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
Product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
Digital I/O Module
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
