POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
Mini Coax, Contact, ITA, two .025" Square Wire Wrap Posts
610103129
Coax Contact (ITA)
Mini Coax, Contact, ITA, two .025" Square Wire Wrap Posts
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
8-Channel, 200 kS/s, 16-Bit DAC Function Card
ProDAQ 3511
-
The ProDAQ 3511 DAC function card is a high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-density card contains eight independent 16-bit DAC channels. Each channel is equipped with its own DAC. Users can update the output of each DAC with up to 200 kS per second either directly via software command or from an onboard FIFO.
-
Product
ABex Terminal Module for Göpel 1149Cx-FXT BSCAN Cards
ABex TM-1149Cx-FXT
-
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SmartNIC Storage Accelerator Card Zynq Ultrascale+
iW-RainboW-G35P®
-
Your product description goes here.
-
Product
Card shaped DC power supplies
RK-80 Series
-
Touch and feel the compactness of RK80 series. Quite convenient to bring from lab to lab, and even you need various different supplies RK80 supplies still save spaces on your desk. Output range selectable function (3 different output range) saves also your investment minimum. As these supplies have digital communication function by integrated microcomputer, it is also easy to built network with other equipment for automation.
-
Product
XMC Mezzanine Processor Card
XMC-528
-
Curtiss-Wright Defense Solutions
The XMC-528 is a high-performance, user-programmable processing and FPGA resource for embedded security applications or use as an FPGA co-processing engine.
-
Product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
-
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 102kΩ
50-298-140
Programmable Resistor Module
The 50-298-140 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
Communications Module
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
FPGA Mezzanine Card (FMC)
FMC DEL
-
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) created to produce pulses delayed by a user-programmed value with respect to the input trigger pulse. It has 4 output channels and one input trigger. The delay from the trigger input to each of the outputs can be set independently in a range from 600 ns to 120 seconds. It is implemented using a dedicated time-to-digital converter IC from the European company Acam.
-
Product
LVDT I/O Cards
IB
-
Computer Conversions Corporation
The "IB Series" product line are full size IBM PC/AT+ and ISA 2.01 compatible synchro, resolver, and LVDT I/O cards, and resolver-sensor card sets used as absolute encoder systems.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
Digital I/O Module
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
Programmable Resistor Module
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCIe Remote Control Interface Card
53-921-001
Remote Control Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input W/ Digital Filter And Interrupt PCIe Card
PCIE-1761H
Isolated Digital Input Card
8 opto-isolated digital input channels8 relay actuator output channelsInterrupt handling capability for all DI channelsSelectable Digital filter time for all DI channelsOutput status readableLED indicator to show activated relaysSelectable Form A or Form C
-
Product
Probe Card Analyzers
PB3600
-
The PB3600 provides the latest techniques in testing and maintaining probe cards. Designed through joint development with many of the world’s largest semiconductor and probe card manufacturers, ITC has produced an ergonomic analyzer with the greatest measurement resolution, highest throughput, most flexibility and still made it easy to use.
-
Product
Low-Profile 16-CH Isolated DI & 16-CH Isolated DO PCI Card
LPCI-7230
Analog Input Module
ADLINK LPCI-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCI-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCI-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCI-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
PCI 39xSPST 2Amp Relay Card
50-132-003
Relay
The 50-132-003 39xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
4-port/8-port USB 3.0 PCI Express Card With 4 Independent Host Controllers
AX92321
-
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 6.97kΩ
50-298-030
Programmable Resistor Module
The 50-298-030 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
LEC-Starterkit with LEC-BASE 2.0 Carrier, SD Card and ATX Power Supply (without LEC Module and Cooling Solution), Optional LVDS Display
LEC-Starterkit 2.0
Power Supply
The LEC-Starterkit 2.0 consists of a SMARC 2.0 compliant LEC-BASE 2.0 carrier board, data media, an AC/DC adapter, power cords and is suitable for LEC-AL, LEC-BT, LEC-BTS or LEC-BW modules.
-
Product
Relay Card
MRM16 / MRM04
-
Our MRM is a relay card for universal connection of many kinds of signals. It serves as a basic module and is available as a variant with 16 NO relays or as a variant with 4 x (7:1) multiplex structure.
