Contactors
Electro mechano connection between the DUT and ATE interface board.
-
Product
Bobbin Winding Coil Turn Tester
SS108 Series
-
This (SS108** series) winding coil turn testers are used for testing turn of various coils without core, like as: generator winding, transformer winding, relay, inductor, contactor, ignition coil, voice coil, etc.
-
Product
Solid State Relays
-
Sensata, through the Crydom brand, continues to be the global leader in Solid State Switching technology for over 45 years, by offering the most extensive range of standard and custom solid state relays and contactors suitable for any load control application.
-
Product
Rack Module with Standard Contactors without Anti-Harmonic filters
MOD Rack
-
Lifasa - International Capacitors, SA
The MOD-RACK control units include, in a compact form, all the components necessary for the operation of a step of a standard capacitor bank. MOD-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
Matrix Switch Module
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
IC & Transformer
-
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
Product
Motor Starters
-
Mitsubishi Electric Automation, Inc
A type of starter for AC motors that combines a magnetic contactor and an overload relay. The MS-T (10-32 amps) and MS-N (35-400 amps) series motor starters offer a compact design and provide reliable protection for your motors against overload and short-circuit conditions in any industrial application.
-
Product
PXI General Purpose 2A Relay Module 16xSPDT, 50 D-sub
40-131-001
Relay
These low cost, general purpose electromechanical relay cards are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 pin D-Type connector plug.
-
Product
Test Contactor/Probe Head
Mercury
-
Mercury™ test probes and contactors are excellent spring probes for the laboratory though they were designed with the robust qualities needed for high-volume production test. Their unique design ensures excellent plating quality for low, consistent resistance, long life, and high-test yields.Mercury probes are available with minimum pitches of 0.3 mm, 0.4 mm, 0.5 mm, and 0.8 mm, to provide the best performance at any device pitch. Mercury probes have bandwidths of up to 22 GHz, and can carry over 3 Amps of current. The Mercury is an excellent choice for any test application.
-
Product
PXI 12xSPDT 16A Power EMR Module
40-161-101
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Kelvin Test Contactor/Probe Head
Gemini
-
At 3.22 mm test height, the Gemini™ Kelvin test contactor is an excellent all-around spring probe with low inductance, high bandwidth, and excellent current-carrying capacity. The device under test (DUT) side tip design accurately maintains its 100 µm spacing for the life of the probe. Customers report typical probe life of 500 k to 800 k package insertions, or over 2M touchdowns at wafer-level test. The offset tip allows manageable board layout with a board-side spacing of 0.4 mm.Gemini Kelvin probes and contactors provide a first-rate solution that effortlessly makes reliable, true Kelvin contact for high-volume final test of both singulated packages and wafer-level devices. Gemini Kelvin is an ideal solution for devices such as power controllers, A-D and D-A converters, power amplifiers and audio and video circuits.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
Multiplexer Module
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
Test Contactor
cDragon
-
cDragon™ Test Contactor pin’s thermal design supports fast temperature control response and stabilization for repeatable at temperature testing of devices in a handler environment.The homogenous MEMS elastomer-free multi-beam pin delivers long life and high wear resistance. By design the cDragon’s pin decouples insertion motion from the test-interface-board side of the pin. This eliminates test-interface-board pad wear.
-
Product
PXI 10 Channel Power Mux 1 Pole
40-660-001
Multiplexer Module
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
Product
Slip-Ring Motor Starting Panels
Rotor Starter
-
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into some steps and controlled via contactors by motor starting control system. As the motor speed increases, the external rotor resistors are eliminated by shorting contactors until all external resistors are shorted out.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
PXI 5A MUX, 1-Bank, 48-Chan, Ind. Isolation
40-651-101
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI 6xSPDT 16A Power EMR Module
40-161-102
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
PXI 5A Power MUX, 8-Bank, 5-Channel
40-651-004
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensationof power factor in low voltage instalations.
-
Product
PXI 2x DPST Power Relay, 2 Slot
40-170-002
Relay
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Turret Kelvin Test Contactor
cHybrid
-
cHybrid™ Kelvin contactor contains a new and unique contact spring architecture which allows the test socket to adapt to challenging IC pad geometry requirements of todays and future small package types. Great lifetime up to 3 million touchdowns, with best-in-class contact resistance repeatability reduces cost of test significantly. A multi-beam contact structure optimizes signal integrity and current capability according to challenging electrical test requirements.cHybrid Kelvin contactor with multi-beam contact spring architecture delivers improved yield and long life minimizing cleaning cycles. This innovative solution will help customers reduce cost and maximize productivity.
-
-
Product
Rack Module with Standard Contactors with Anti-Harmonic Filters
MODF Rack
-
Lifasa - International Capacitors, SA
The MODF-RACK control units include, in a compact form, all the components necessary for the operation of a step of a capacitor bank with filters. MODF-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
Product
Single 8x2 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-012
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
Test Contactor/Probe Head
xWave
-
Highest performance and most robust RF broadband production solution for package, wafer, or Over-the-Air (OTA) test for 100 GHz.The xWave™ test contactor / probe head utilizes patented hybrid contacting technology to optimize RF performance and provide robustness for production testing of the most challenging cmWave and mmWave devices. Inside the xWave test contactor / probe head are embedded patch antennas and coplanar waveguides for both wireless and wired communication.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
PXI 5A Mux 1-Bank 48-Ch Isolated COM + Ind Isolation
40-651-111
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
