Contactors
Electro mechano connection between the DUT and ATE interface board.
-
Product
Single 8x2 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-012
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
PXI 10 x SPST 10 Amp Power Relay Module
40-160-001
Relay
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Process Ozone Monitor
Model 465M
-
Teledyne Advanced Pollution Instrumentation
The Model 465M is a microprocessor based medium range ozone monitor for measuring process ozone concentrations in water treatment, food processing, and research applications. The design has been specifically optimized for applications requiring the measurement of ozone at near-ambient pressure such as water treatment contactor off-gas measurement. The Model 465M has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465M is available in a NEMA 4X wall mount enclosure.
-
Product
LCZ LCR Meter
SS1062
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor, cable, wire, etc..
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
Matrix Switch Module
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
16 Channel Power PXI Multiplexer, 2 Pole
40-650-002
Multiplexer Module
A 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. It is suitable for applications requiring switching of either mains voltage or DC.
-
Product
PFR96
2WE06
-
The digital controller PFR96 can manage up to 12 independent batteries, a communications port, and two current inputs in size from 96×96 framework. Particularly easy to program thanks to a basic configuration with two parameters and advanced that allows the advanced user the most complete of the power factor correction control.The onboard logic allows corregegre setup via an erroneous wiring of the picture as to or stage of TA.10ms sampling of the voltage allows the calculation of the RMS voltage continuously, identifying network holes and temporary interruptions and detach the active steps immediately to the protection of the contactors and benches.The PFR96 can handle numerous alarms associated to available relays.The means of intervention in the PFR96 adjustment are all customizable for a better quality of the intervention as well as the use of different banks can be equalized for less wear of the contactors.Sampling at variable frequency and RS485 communication for remote control (PFR96 Plus) complete a range of services offering maximum control and quality of the measurement
-
Product
PXI 12xSPST 16A Power EMR Module
40-161-002
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
High Performance Chipscale Test Sockets
SC
-
Ardent Concepts Test Sockets for ATE test deploy patented SC Contact Sets. This technology is capable of over 2 Million mechanical insertions in production environments and uses easy to replace pins with no complicated assembly procedure. It is designed to be drop-in compatible with 1mm offset and straight through footprints to ease implementation, and RC SC’s simple and robust design is extremely cost effective when compared with existing “roll” type test contactors and sockets. Designed specifically for JEDEC QFN and MLF applications, SC High Performance Test Sockets are available for most handler set-ups and offer exceptional AC performance.
-
Product
Test Contactor
cGator
-
cGator™ singulated power contactor is a top and bottom contacting solution for power Known Good Dies (KGD).Cohu´s patent pending Volta-Flux™ MEMS probe architecture technology provides stable and low CRES for very challenging high-voltage and high-current requirements.The gentle-touch feature reduces surface impacts to a minimum while providing a reliable contact force.
-
Product
Dual 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-012
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
Matrix Switch Module
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
Quad 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-001
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI 18 Channel Power Mux 1 Pole
40-665-001
Multiplexer Module
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
