System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 1.51MΩ
50-297-144
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-02
Digital Waveform
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
PXIe-2525, 64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module
780587-25
Multiplexer Module
64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module —The PXIe‑2525 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in one of the following 2‑wire multiplexer configurations: 16 bank 4x1, octal 8x1, quad 16x1, dual 32x1, and 64x1. The PXIe‑2525 also features onboard relay counting for relay monitoring.
-
Product
Digitaler I/O Mit 16 Kanälen
MDS
-
The static driver sensor module (MDS) is used to replace existing TS02 from previous MTS test systems. The possible pin extension allows to replace the systems MTS 200/210 (4 UCB with 4 MDS = 256 pins). A maximum of 1,024 MDS pins can be realized on the current MTS systems. Up to 4 MDS modules can be connected to one UCB (UCB03 or higher).
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 3Ω to 102kΩ
40-298-034
Programmable Resistor Module
The 40-298-034 is a high density programmable resistor module with 9 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Magnetic-Field Test System
MTS-800
-
The MTS-800 is a compact test system for broadband generation and measurement of magnetic fields. Its internal components allow automatic EMC tests according to automotivestandards where high field strength need to be generatedor measured.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Automatic Hysteresis Graph Test System
DX-4DMT
-
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 470Ω
50-298-114
Programmable Resistor Module
The 50-298-114 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Avionics Databus Modules
-
Avionics interface modules from Avionics Interface Technologies, offered through Keysight, enable connectivity between your PXI test systems solution to DUT’s with aviation industry standard buses. These modules are capable of simulation, monitoring, record and play back of bus traffic enabling test and verification of avionics equipment data communication capabilities. The available interface modules support industry standard avionics based buses such as MIL-STD 1553, ARINC 429, and ARINC 664p7, and Fibre Channel.
-
Product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
In-Circuit Test System Calibrations
Test System
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
Product
Power Module And Device Testing System
-
Dynamic and static test system Meet the power IPM module dynamic and static electrical parameters test
-
Product
High Density, 64-Channel Switch Card - 64 Channel, SPDT, High Isolation, Low Crosstalk Switch Module
1260-16A
Switch Card
The Astronics 1260-16A is a 64-channel, SPDT, high isolation; low crosstalk switch module designed for switching and routing sources such as AC and DC power supplies in automated test systems. The 1260-16A switches currents up to 6A, AC or DC, and voltages up to 110VDC or 250VAC.
-
Product
In-line vacuum test systems
-
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
-
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Diabetes Testing Products
-
Bio-Rad has been at the forefront in developing the world's most accurate and precise diabetes testing products. Today, Bio-Rad offers a full range of innovative HbA1c products for clinical laboratories, hospital laboratories, clinics and physician office laboratories. All Bio-Rad diabetes testing systems are NGSP (National Glycohemoglobin Standardization Program) certified, traceable to the DCCT (Diabetes Control and Complication Trials), and anchored to the IFCC reference method.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 102kΩ
50-297-040
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Test Chamber for Dynamic Vibrators
-
The focus of the Feutron climate simulation overall concept is on the simplest operation of the overall functions of the test systems and the highest reliability with maximum efficiency. This is why our systems are supplied as plug-in compact devices.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 201kΩ
50-297-141
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 1.81k
40-297-022
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
LCR Meter
TH2810D
-
Changzhou Tonghui Electronic Co., Ltd.
TH2810D/TH2811D LCR meter is our newly developed successor instrument for low frequency component measurement. TH2810D/TH2811D with its latest measurement technologies, large character LCD display, surface mount technics, easy of use and excellent appearance can be used for quality control on production line, incoming inspection of components and automatic test system. The RS-232C interface can be used to carry out remote control and statistics and analysis of measurement results.
-
Product
Software
DIGITIZER
-
The Digitizer allows the recovery of design data of unknown assemblies by an electrical analysis with a Condor flying probe test system
-
Product
Flying Prober Test
QTOUCH1202C
-
Qmax Test Technologies Pvt. Ltd.
he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Swiss 220VAC
781630-02
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Damped Oscillatory Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
Product
VX4 System
PrecisionWoRx
-
The PrecisionWoRx VX4 System gives test facilities and probe card manufacturers the ability to confidently test tighter pitches and smaller probe tips. The system can be easily configured to specific requirements for a variety of probe card technologies. For processes using cards with very small probe tips, the system’s high-resolution optics deliver a detailed field-of-view for high accuracy and repeatability.
