Processing
Manipulates and analyzes a signal.
-
Product
PCIe Mono Industrial Camera
CMOSIS CMV2000
-
2K camera Applications: In-situ optical inspection camera, fast process capturing, e.g. Golf club swings, Intelligent Transportation Systems (ITS), Open road tolling and Traffic monitoring, Industrial Automation, Machine Vision, Facial Recognition, Motion Capture, Automotive crash testing, OCR/ OCV, 3D scanning, Robotic Arms, Material and Life science Microscopy, Ophthalmology and Retinal imaging, Medical Imaging, Flat panel inspection, Dental, Kiosks, Security, Biometrics
-
Product
Flashback Arrestors
-
Although working with fuel gases is a safe process in the hands of trained personnel, it can lead to a dangerous situation if the equipment is used incorrectly. Fuel gases should not be used unless proper safety procedures have been understood and applied.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Magnetostrictive Level Transmitter
DM330
-
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
Product
Test development service
-
Test development may be a complex task, because each emulated session must be unique and consistent. Unless the website consists of exclusively static pages, there is no testing tool that can fully automate the test design process. In many cases the implementation may require considerable research of the client-server communication scheme.
-
Product
Large Format - Step & Repeat Tester
GATS-8300
-
The GATS-8300 Tester is one in a series of Test Systems designed for testing multiple-image panel using a Step & Repeat process. Rather than fixture the entire panel for electrical test, you simply fixture for one (or more) images. The GATS-8300 will Step the fixture across the entire panel and Repeat the electrical test at each step.
-
Product
360° Edge Analytics
-
360° Edge Analytics fills the gap between location data and the individual business application. The Location Data Analytics technology leverages precise position data augmented by application context information to gain business insights from complex processes. Assessment, optimization as well as process restructuring will be possible with nanotron’s complete solutions based on its Location-Aware IoT Platform with Location Data Analytics.
-
Product
Multi-channel Bench-Top Power Meter
STC-BTOPM2101-M
-
Shanghai Stone Communication tech Co., Ltd
This multi-channel bench-top power meter is the high precision and wide measurement range test instrument. Which have intelligent micro processing control, and auto-shift of measurement range. This equipment have 8 laniary processing, which can avoid the difference caused by the non-laniary effect in different wavelength, and output power. And this will make the equipment much more stable and reliable in operation. With features of accurate measurements, durable use and easy operation, It becomes a perfect test equipment in fiber optic works which can instead the advanced imported products with its high cost-performance ratio.
-
Product
Spectrometer Systems
-
ZEISS spectrometer systems leverage our longstanding experience in process optimization and expertise as a pioneer in scientific optics. Regardless of whether it’s in the lab, on the production line or in the field, plan your next project with ZEISS and benefit from:
-
Product
FPGA 6 Gsps Transceiver
VPX3-534
-
Curtiss-Wright Defense Solutions
The VPX3-534 combines high-speed multi-channel analog IO, user programmable FPGA processing and local processing in a single 3U VPX slot for direct RF wideband processing to 6 Gsps. This card allows for a high performance single slot transceiver with two 6 Gsps 12bit channels, to over 6 GHz instantaneous analog bandwidth, but can also scale to larger system with many channels.
-
Product
Battery Short Circuit Tester
TOB-BSCT-01
-
Xiamen Tob New Energy Technology Co., Ltd
Battery Short Circuit Tester For Not Charging Semi-Finished Battery Core Checking Out. This Battery Short Circuit Tester is used for check out NG batteries for battery core without electrolyte filled or before battery charging. For lithium battery research, it is used for battery core after winding process or stacking process to check out bad battery with automatic alarm.
-
Product
3D Software
Geomagic Design X
-
Geomagic Design X is an all-round, professional reverse engineering software with a smart combination of history-based CAD with 3D scan data processing, letting you produce feature-based, editable solid models compatible with your existing CAD software.
-
Product
Universal Input Meters
-
Omega offers a large selection of Universal Input Meters that accept a wide variety of input signals including DC voltage/current, process, resistance, strain and temperature.
-
Product
Digital Module For Remote I/O
-
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
-
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
-
Product
Manual Testing Services
-
With manual testing services, we will hand-pick a team dedicated solely to your project. Our professionals will work with your developers, business analysts, and managers to go over requirements, build a comprehensive test plan, design thorough test cases, rapidly execute the tests, help remediate defects, and retest until the project is satisfactorily completed. The same individuals will be with you from beginning to end, so they have a complete understanding of the project and how you want it done, and you will always know exactly who you are dealing with. The same QA Engineers that develop the test cases will also execute them, leaving no room for misunderstandings and greatly expediting the process.
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SFF Subsystem
Model 6353S
-
- Complete RF converter and processing subsystem- Rugged and conduction-cooled- Ideal for integration into custom enclosures- Incorporates Xilinx® Zynq® UltraScale+™ Gen 3 RFSoC- 16 GB of DDR4 SDRAM- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
MRI POWER SUPPLIES
-
MRI Power Supplies are used in MRI Imaging rooms in hospital environment. The lights in the MRI rooms require DC power. If AC power is used, the quality of the MRI imaging process is compromised. These units are ideal for MRI room, where a 60 Hz flicker free light environment is desired. CEHCO offers four models which are shown below.
-
Product
Multifunction Calibrators
-
Easy-to-use Multipurpose instruments for advanced documented calibration and process control.
-
Product
Fibre Channel Modules
-
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
Product
EMC Testing EMCD
-
Efficient and flexible EMC testing services for product CE marking, UKCA marking and demonstrating compliance with US FCC and Canadian ISED regulations. Our experienced engineers will guide you through the test process, helping you to save time, minimise project costs and get your product to market quickly.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
-
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
CrashSim Office
-
CrashSim Office is a stand-alone program for signal preparation and processing, as well as for predicting the pulse-making capability and the generation of the DriveSignal for the CrashSimulationSystem. CrashSimOffice is used offline from the crash simulation system and has essentially the following characteristics
-
Product
Optics
-
Welcome to Thorlabs; below you will find links to optical components and systems, a subset of our entire line of photonics products. All single element optical components can be found under the optical elements link with the exception of optical components that have polarization properties since they have a separate link. Multi-element systems like beam expanders and objective lenses as well as interferometers, fiber collimators, reference cells, modulators, and other optical devices can be found by choosing the optical systems link. Thorlabs also manufactures an extensive line of free-space and fiber optic isolators; stock items ship the same day that they are ordered while our custom orders benefit from our streamlined design and manufacturing process, which minimizes lead time.
-
Product
Single Channel Detectors
-
Infrared detectors for gas analysis, flame detection and radiometry in TO18 or TO39 packages.Housing types TO18 and TO39Voltage or current modeSignal processing with JFET or operational amplifierThermally compensated (optional)With special chip holder for reducing the microphonic sensitivity (optional)
-
Product
DFM (Deep and Fast Modulated) generators up to 280 GHz
-
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
PROBE CARD
-
the electrical characteristics of the individual CHIPs in WAFER that have been completed through the FAB stage during the semiconductor fabrication process
-
Product
High Speed Comparators (<100ns Propagation Delay)
-
Analog Devices high speed comparators feature <100 ns propagation delay and are a versatile and easy to use solution for a range of applications. Owing to our proprietary CB and XFCB fabrication processes, our comparators such as the AD790 possess a fast response time with outstanding input voltage resolution.
-
Product
Workstation Software
LabSolutions Balance
-
When connected to an analytical balance, LabSolutions Balance can be used to perform all processes automatically, such as calculating weighing results, and then save the weighing results in a LabSolutions database. Consequently, it eliminates the need for hand-written records and eliminates transcription errors. The software not only records sample information and results, but also protects data from malicious alteration and unintended overwriting or deletion and saves all audit trail information in a LabSolutions database.
-
Product
PC Software
AMA.REMOTE
-
On the one hand the PC software AMA.remote allows you to process measuring receiver files (e.g. tuning memory or channel lists). On the other hand, TV analyzer (combo measuring receiver) AMA 310 can be remotely monitored and controlled via SNMP with AMA.remote.
