Processing
Manipulates and analyzes a signal.
-
Product
PXIe-57857, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785586-01
FlexRIO IF Transceiver
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Test And Measurement
-
Test and Measurement supplies test, measurement, and analysis equipment and software for product design optimisation, manufacturing control, and environmental monitoring systems. Markets are principally the aerospace, automotive, consumer electronics and oil and gas industries. For customers in the automotive and aerospace industries, our products and applications help them to design and test new products whilst reducing time to market. In consumer electronics, our equipment and software enable customers to refine the performance and accuracy of their products and to test them in the production process. In the environmental monitoring market, the desire for higher standards of community comfort is creating additional demand. In the oil and gas industries, our products and solutions optimise the recovery rates of oil and gas reservoirs and support the development of cost-efficient extraction processes in a safe manner that minimises the impact on the local environment. The operating companies in this segment are Brüel & Kjær Sound & Vibration, ESG Solutions, HBM and Millbrook.
-
Product
Digitally-Tuned Matching
Navigator II
-
The Navigator® ll is equipped with microprocessor-controlled, stepper-motor drives, and advanced tuning algorithms — enabling optimized RF power. An optional internal Z’Scan® II RF sensor provides real-time analysis of process power and impedance — allowing you to quickly identify and significantly reduce process variability. Optional Virtual Front Panel software is available for monitoring and control through a user’s computer.
-
Product
1.25GS/s 16Bit 1GS Mem 2CH 4 Markers AWG
P1282D
Waveform Generator
The Proteus P1282D, is a 1.25GS/s, dual channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit and perform digital signal processing all in a single instrument. The P1282D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
Turbidity Probes And Turbidity Meters
-
Insertion-style and Immersion-style, with a variety of measuring ranges and process environments
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Leeb Hardness Testers
-
GAOTek proudly presents an extensive and wide range of Leeb hardness testers for sale to the United States, Canada and globally. A Leeb hardness tester is used mainly in the manufacturing industry to test the structural integrity of a metal object by applying a definite amount of force on the object. Structural integrity is crucial information as in some cases it is treated as a specification or standard that companies must meet in order to release a product. It may also be used to set a limitation or restriction for a specific device or item. Our testers are designed to ensure standards are met by providing users with a variety of features to make the process of testing and monitoring results efficient and convenient.
-
Product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
Test Platform
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
Product
UHD Real-Time Video Appliance
-
The VEGA 6000 family of compact video processing appliances supports ultra-low latency 4K HEVC encoding, decoding and IP media streaming.
-
Product
VisualIMPACT Software
-
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
Product
Functional Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Functional testing is a very important process for amplifying the quality of the software development life cycle. Functional testing mainly shows black box testing, which evaluates a particular IT product with the specific functionalities that indicate its specification. Therefore, to promote competencies and to convey a great product, it is necessary to perform a functional testing process.
-
Product
Chemical Resistant Chilled Mirror Sensor
X3
-
Edgetech Instruments NEW X3 Chemical Resistant Chilled Mirror Sensor exploits the latest advancements in optical sensing and is specifically designed for demanding Process and Laboratory applications. It also offers the advantages of low dew point detection and rapid response. Available in multiple configurations to accurately measure dew point in aggressive background gases including. Ammonia, HCl, SemiCon Gases, Peroxides, Medical Gases, and other reactants.
-
Product
Flight Testing
-
ATA Engineering has developed flexible low cost methods to satisfy our customers' flight testing needs. We are able to provide innovative solutions to acquire and process all types of flight testing data without requiring expensive software and hardware solutions.
-
Product
Power Supplies
-
Reliable power supplies enable data acquisition systems to continuously acquire and process data. Because our components use minimal power, many of our systems can be run using sealed rechargeable or alkaline batteries. Systems that require more power are often supplemented with external rechargeable batteries, regulators, ac transformers, or solar panels.
-
Product
2-port Battery Portable Passive Intermodulation Analyzer - iXA Series
iXA
-
The Kaelus iXA Series Passive Intermodulation (PIM) analyzer is a dual-port, battery powered PIM Test Analyzer. It supports multiple test scenarios such as testing at the top of the tower, the base of the tower, rooftop, in-building for DAS systems and external PIM Finding.No other PIM tester has ever been integrated to this level! The iXA includes a network of electronic switches to change from one-port to two-port measurement seamlessly. In addition, with integrated Range-to-Fault (RTF) on each port, the user can first troubleshoot the system for internal PIM. Then, without reconnection, the user can progress with the external PIM process, making the entire process much more efficient.With integrated RTF on each port, the user can collect four times more range-to-fault data than the standard 1-port PIM Finder solution. Thus, the user can easily locate and swiftly eliminate the strongest PIM source.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Electroluminescence Test Systems
-
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
Product
Calibration Software
-
Calibration software is available to automate all or part of many calibration processes, manage calibration and asset data, and perform other useful tasks as well. Fluke Calibration offers a variety of market leading software applications in each of its product disciplines.
-
Product
Non-Destructive Testing (NDT) Services
-
We help you ensure the reliability and safety of your products, equipment or plant assets with our world-class services in non-destructive testing (NDT), materials testing and welding quality. We understand the processes involved throughout the entire product cycle – from design and manufacture to operation and maintenance - and the frequent need for rapid turnaround times. Our Total Quality Assurance services can support production processes, quality control, and regulatory compliance as well as new construction, pipelines, plant maintenance and scheduled shutdown inspection.
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786856-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
kSA Scanning Pyro
-
For use on Veeco K465i and EPIK700 MOCVD reactors, the kSA Scanning Pyro performs automated temperature mapping in order to measure temperature variations across wafer carriers and wafers. Use it to tune heater zones and optimize process and hardware to achieve higher yields, wafer uniformity and device performance.
-
Product
EMV Personalisation Validation Test Tools
-
EMV personalisation validation testing enables issuers and card bureaus to validate and pre-certify their cards against the latest payment scheme specifications, as well as the issuer's business requirements. This prevents the costly production of invalid EMVcards and delays in the formal card certification process.
-
Product
Pitot Static Tester / AoA TESTER
ADSE 744
-
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Product
Counters and Timers
-
Orbit Controls counters and timers are designed for connection to practically all industrial sensors and pulse sources . They can be used as process monitors to display the process variable to be measured or as process controllers for control and monitoring tasks. The devices display and process pulses and frequencies, as well as quadrature signals from incremental and absolute encoded rotary encoders. In addition to information on the display, the devices also generate data and analog outputs and monitor preselected limit values. The process parameters are entered via the keyboard so that the display is calibrated in the required units and the output signals, serial interfaces and limit values are optimized.
-
Product
CT Tester
6000 Bird Dog Plus
-
Spinlab Utility Instrumentation, Inc.
This new and exciting true 3 phase Bird Dog Plus enables you to determine the accuracy of any meter in the field--from Form 1 through Form 17. Electronic sensors allow you to automate the test to gain the highest possible accuracy. The process is fast, simple, and much less expensive than a portable test board for the meter test and still perform ratio & burden tests on your CTs (CT Tester).
-
Product
Variable Optical Attenuator
-
Shenzhen Golight Technology Co.,Ltd
Variable optical attenuator uses high-precision attenuation control components, and combines a selfdeveloped embedded data processing platform and precise calibration process, can be provided with maximum 60dB optical power attenuation and optical power monitoring function. Real-time display of input and output optical power.
-
Product
3D Cameras
-
Imaging Development Systems GmbH
3D Machine Vision is considered to be the future of Robot Vision. The integration of 3D data makes it possible to precisely capture and interpret the environment, enabling tasks in robot technology to be solved more efficiently. This applies both to demanding assembly processes, such as gluing or welding, and to the notoriously tricky process of "bin picking". With the Ensenso 3D cameras and the Nion ToF camera, IDS offers powerful camera systems for 3D imaging – with a focus on precision, cost-effectiveness and easy integration.
-
Product
Electrical Resistance Probes
-
Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.
-
Product
Thermo-hygrometer Handheld Temperature And Humidity Meter
HW100
-
Shenzhen Chuangxin Instruments Co., Ltd.
HW100 temperature humidity meter is a portable temperature humidity test instrument., selecting high performance capacitor type polymer film humidity sensor and semiconductor type temperature sensor. It has features of volume small, weight light, easy carrying, multi-function, and high precision, etc., applies to various fields such as hot comfortable research, indoor air quality assessment, verification of HVAC system run situation in building, heating and refrigeration system overhaul, and detection of the air conditioning system during the production process and so on.
-
Product
Octane Number and Cetane Meters
-
Labodam Octane Number and Cetane Number Testers are portable devices for rapid petroleum products quality monitoring in fields and lab environment conditions. Glass detector has a built in element sensitive to fuel sample temperature detection. The instrument electronic computing module processes detector signals, performs all necessary calculations, and constantly tests the main function modules. It is ideal used in the determination of octane, cetane numbers, our point depressants and break down time in the oil and petroleum industries.
