-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
P104 Synchro/Resolver Measurement Board
73SD4
-
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
Product
Bit Waveform Digitizer Board
ATS9373
-
ATS9373 is a 12 bit waveform digitizer board that can sample one analog input at rates up to 4 GS/s or two inputs at 2 GS/s. With on-FPGA FFT signal processing and data throughput as fast as 6.8 GB/s (6800 MB/s), ATS9373 is an ideal solution for many applications, including next generation OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
Product
Expansion Board
MSXB 044
-
The MSXB 044 expansion board works with the iDSC 1816 to add signal conditioning to the data acquisition and anti-aliasing capabilities. Four MSXB 044 boards are included in each MSSC-8 module. Purchase the MSXB 044 as part of a complete SCS system: an enclosure and 1, 2, 3, or 4 MSSC-8 modules, for a total of 8, 16, 24, or 32 channels.
-
Product
Digital Output Board, 32 Isolated Channels, 24V
APCI-2032
-
32 digital outputs, 24 V or 5 V, 500 mA/channel Optical isolation 1000 V Overvoltage protection Short-circuit protection WatchdogAt power-on the outputs are reset to ì0î
-
Product
PCI Express Board Retainer
SKU-038-0X
-
The PCI Express Board Retainer prevents the host card from wiggling, and allows a PCI Express board to be held in place without a bracket.
-
Product
SparkFun MicroMod Environmental Function Board
-
The SparkFun MicroMod Environmental Function Board adds additional sensing options to the MicroMod Processor Boards. This Function Board includes three sensors to monitor air quality (SGP40), humidity & temperature (SHTC3), and CO2 concentrations (STC31) in your indoor environment. To make it even easier to use, all communication is over the MicroMod's I2C bus!
-
Product
Temperature Measuring Board
W16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature Measuring Board conform to IEC60335-1:2004 and GB4706.1-2005 can be used to the temperature test of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.
-
Product
Single Board Computer
-
Hartmann is proud to partner with Orion Technologies, LLC — a distinguished leader in specialized embedded single board computers (SBC) as well as full system design and development. This cutting edge technology is used in a variety of military, industrial, and commercial applications.
-
Product
COTS PC/104 Carrier Cards and Boards
-
Sundance Multiprocessor Technology Ltd.
COTS PC/104 Carrier cards and boards
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
NO LOAD & LOAD TEST BENCH
-
International Biological Laboratories
These are the test benches incorporating control & measurement circuitry necessary for testing single phase as well as three phase transformers of several VA to MVA rating & voltage class of 11KV/433V,as well 33KV/11 KV, after manufacturing, repairing, reconditioning. Following tests can be done by these Test Sets.
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
6U Processor Board
CP62103
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62103 is a modular design, based on COMexpress® technology, up to 4-core i7 processor from Intel® Ivy Bridge family. CP62103 is designed to meet harsh environment applications like rural communication, military, medical and outdoor video processing.CP62103 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.
-
Product
DC Electronic Load
M9822/M9822B
-
M9822/M9822B is newly designed circuit adopts rapid AD and DA technology to achieve rapid measurements with high accuracy. And the resolution of 0.1mV/0.1mA can effectively display the minor change of voltage and current, so the instrument has a wider application field and achieves better test results. Meanwhile your operation becomes much more comfortable and easy by equipping the high-light VFD, the simple menu and displayed contents and the operation state indicators on all keys. Otherwise the complete and humanized test functions will greatly improve your productivity.
-
Product
JD Edwards Load Testing
Dimension LoadTest
-
Dimension LoadTest™ is a powerful yet easy to use load testing tool for JD Edwards EnterpriseOne applications. DWS have designed Dimension LoadTest such that any experienced System Administrator/CNC should be able to setup, create, run and monitor load tests to effectively stress test JD Edwards EnterpriseOne applications.
-
Product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
Relay
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
Product
Board cameras
-
Tried and tested, The Imaging Source board-level cameras are optimized for cost sensitive, high-volume machine vision projects and offer maximum flexibility for a wide range of space-limited applications.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
Load Resistor Module
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
Product
Video Detection Boards
VIP-3D Series
-
The VIP series offers multi-functional Video Image Processing modules for traffic control. These boards can monitor single or dual cameras and provide accurate data traffic volume, speed, gap-time, headway, occupancy, concentration, and classification. Data is stored on-board, using non-volatile memory.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board
-
Same features of 8 Channel Sample & Hold and Signal Conditioning Board plus connection and transient protection for Group3 B (digital) and D (analog output) boards.
-
-
Product
I/O Board
-
For more expansion and convenience, we offer a ready to use I/O boards which are specially designed for Pico-ITX SBCs.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
Load Cells
-
We make it our business to stay on top of emerging industry demands so that the load cells we provide help you meet your ever-changing test requirements. Our broad selection of competitively priced load products will help you meet the most demanding test and measurement requirements. Used in automotive, aerospace and defense, R&D, and process control applications, our drop-in replacement load cells are designed to provide years of dependable performance.
-
Product
ARM LPC2294 Based Board
MS 2500
-
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
Product
Portable Hand Held Load Cell Indicator
MODEL SSI
-
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
Product
COM Express Boards
-
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
