-
Product
ELECTRONIC MEGOHMMETER
MI-1050e
-
The MI-1050e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 1 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 2.000.000 MΩ with four test voltages: 100 V, 250 V, 500 V and 1.000 V.
-
Product
Automatic Test Equipment for Electronic Systems
-
BAE Systems has designed and manufactured comprehensive test solutions for both military and commercial applications for more than 40 years. During this time, we have kept pace with the rapidly evolving market to deliver integrated, commercial-off-the-shelf solutions to our customers. Our test equipment consists of an open architecture, adaptable core that can easily integrate with additional instrumentation. This enables the development of unique configurations that support the full spectrum of avionics and electronics in use today.
-
Product
High Load Strength Tester
HLST1000Z
-
This tester measures the tensile or compressive strength of various samples
-
Product
ESI(Electronics Systems Integration Unit)
MS 2004
-
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
RF Coaxial Load
-
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
Product
Dynamic Mechanic Loading Tester
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material：aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Product
Electronic Crockmeter
-
TESTEX Testing Equipment Systems Ltd.
Electronic Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. A pinned acrylic sample holder ensures rapid sample mounting and repeatability of results. Crockmeter Fitted with a pre-determined electronic counter for strokes up to 999,999 times.
-
Product
Electronics & Power
-
Excelitas Technologies offers a wide range of high-performance electronics, power and energetics technologies to drive your most demanding photonic systems. Our Electronics & Power offering includes Capacitor Chargers, Spark Gaps and Transformers, High-Voltage DC Power Supplies and Atomic Frequency Standards. Our Energetics portfolio includes Electronic Safe & Arm devices, Detonators, Ignition Safety devices, and Rocket Motor Initiators.
-
Product
Electronic Component Counter
ZE 300
-
REINHARDT System- und Messelectronic GmbH
Instead of the widely used photoelectric barrier technology a new measuring technology is used in the new electronic component counter ZE 300: The laser technology offers a measuring beam with higher energy density and therefore more precise counting and faster counting speed. The ZE 300 component counter is microprocessor-controlled.
-
Product
High-Performance Application and Security Load Module
PerfectStorm 10/1GE Load Module
-
Keysight Network Applications and Security
Equipped with powerful multi-core, multi-threaded network processors, PerfectStorm 10/1GbE is designed to satisfy the testing needs of manufacturers needing speed flexibility in their testing resources. Networking equipment manufacturers building new equipment or service providers and large enterprises integrating this them benefit from testing and verifying performance and functionality prior to deployment.
-
Product
LV Iron Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
-
Product
Electronic Testing Services
-
Printed Circuit Board Testing and Repair Services CM Wings Board Testing Inc. was founded in 1983. Its founding was a direct response to theneed for a truly customer service oriented facility for printed circuit board test and repair.
-
Product
Simulation Tools for Analog and Power Electronics
SIMetrix/SIMPLIS
-
Fast and accurate simulator for switching power circuits, fully utilising the SIMetrix development environment.
-
-
Product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
-
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, 4.3-10, 2 Port
85094D
Electronic Calibration Module
The Keysight 85094D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Electronic Circuits
-
1. A complete laboratory training system. 2. Understanding the theory and application of basic electronnic circuits. 3. Suitable for both technician and beginner of electronic students.
-
Product
48V / 300 Amp Load
BD18-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Electron Beam Lithography System
-
Spot type Electron Beam Lithography System JBX-8100FS achieved high throughput, small footprint and electric power saving.
-
Product
Scanning Electron Microscope w/ EDX Laboratory
-
Trialon has the equipment and experienced staff to operate this highly technical piece of laboratory equipment. Our state-of-the-art materials analysis lab located in Auburn Hills, MI is managed by a Ph.D with over 20 years of hands-on experience in root cause failure analysis of design, material and process for current and future products.
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
Electronic Primary Injection Test Set
eKAM
-
eKAM is the new fully automatic electronic primary injection test equipment. e KAM test system includes two portable units: one control unit with a large graphical display, that adjusts the output, and one current unit (up to 2000, 3000, 5000A). It can also perform Step and Touch tests and ground resistance tests.
-
Product
High-end Transmission Electron Microscope
CryoARM
-
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
-
Product
Power Transducers and Load Loggers
-
Power Transducers and Load Loggers by Ametek Power Instruments
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Three Phase Electronic Meter DTS999
-
Bofa Instrument & Equipment Co., Ltd
DTS999 series Single Phase energy Meter are new and high-tech products adopting special large-scale IC, latest micro-electronic technology and SMT production crafts. It is designed for rough working condition and components selection as foundation, so it can ensure the long-term stable operation. DTS999 series Electronic Single Phase Watt-hour Meter features long life, high accuracy, high reliability, high allowable overload, little power consumption, small size & light weight, etc.
