-
Product
Source Measure Units (SMUs)
B1511B
Source Measure Unit
The SMUs of B1500A integrate 4-quadrant voltage/current source and measurement capabilities for accurate IV measurement with the range of 0.1 fA - 1 A / 0.5 µV - 200 V. It supports spot, sweep, pulse sampling and QS-CV measurements.
-
Product
High Voltage SMU 2500 V
AXV7607
-
Generate extremely short, fully regulated voltage pulses of up to 2500 V. Measure leakage currents up to the pA range.
-
Product
High Voltage Film Capacitors (Axial Leads)
STVHF/STVHE-A
-
For High Pulse / High Energy Discharge applications with low discharge repetition rate, please tell more about your application. We might have a suggestion.
-
Product
High Current / High Voltage Pulsers
DEI Division
-
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
Product
S-band Klystron 3 GHz/3MW
-
Insight Product Co. 's S-band, 3 GHz, klystron provides up to 3.0 MW of output pulse power.
-
Product
ESI(Electronics Systems Integration Unit)
MS 2004
-
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
Product
Proximity Sensors
600 Series
-
600 Series Proximity Sensors are active digital sensing devices that generate one pulse per pass of an actuating target within their sensing field. No direct contact with target material is necessary. Each sensor is entirely solid state with no moving parts to wear out.
-
Product
Counters, Timers, And Ratemeters
-
ORTEC offers the broadest range of nuclear counters, timers, rate meters and multichannel scalers. Counters simply count the number of input pulses received during the counting period. Timers count pulses generated by an internal or external clock and are used to measure elapsed time, or to establish the length of the counting period. Rate meters provide a readout of the pulse count rate. Multichannel scalers count the number of events that occur during a specified time interval, referred to as the dwell time, resulting in a time-histogram of counts. “Standalone” and programmable computer controlled versions are available.
-
Product
Low-Cost Alternative to EWPro™
SigRec™
-
Research and Development Solutions, Inc.
SigRec™ is an easy-to-use low-cost alternative to EWPro™ for Electronic Warfare signal recognition training. It combines a signal list with an Oscilloscope and AN/ULQ-16 pulse analyzer emulator for analysis of signals. Signal audio is also generated through a standard PC soundcard.
-
Product
CAMAC Multifunctional Logic Unit
CMDGG8
-
The CMDGG-8 is a multi functional FPGA based delay, logic and timing module which provide often needed functions such as gate, delay & pulse generator, logic fan in / fan out, coincidence register and scaler / pre-scaler.
-
Product
High-Performance Autoranging DC Power Module, 20V, 50A, 500W
N6755A
Power Module
The Keysight N6755A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Arbitrary Function Generator PXI Card
GX1200/GX1201
Waveform Generator
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
Non-contact Conductivity Type (P/N) Checker For Quick Check
PN-50α
-
*Principle: Photovoltaic effect by light pulse irradiation*No damage and no stain by Non-contact method*Possible to check even oxidized film on wafer surface*Instantly discrimination by optical pulse illuminate
-
Product
TMR Rotary Encoders
-
MultiDimension Technology Co.,Ltd.
• on axis assembling• Incremental• Pulse output
-
Product
Mode Locked Synthesizer
IT9200
-
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
Product
Multi Functional VME Logic Module
MDGG-16
-
The MDGG-16 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate generator & pulse generator, logic fan in - fan out, coincidence register and scaler / pre-scaler. The module has 16 LVDS/ECL inputs and 16 ECL outputs on pin headers and 2 NIM inputs as well as 4 NIM outputs (Lemo), which are free configurable in regards to their functionality.
-
Product
Autonomous RTU
BSC-50E
-
Infinite Industrial Informatics Lt
BSC-50E is an ultra low power, wireless RTU with data logging and alarming capabilities. The battery powered RTU incorporates a quad band GSM/GPRS modem, four digital inputs, three analog inputs, two pulse counters and multiple excitation options for powering measuring transducers.
-
Product
Real-Time Waveform Averaging Firmware
FWATD
-
The Advanced Time-Domain firmware option, FWATD, equips the ADQ7 and ADQ14 digitizers with advanced tools for sophisticated time-domain measurements. Multiple steps of noise suppression is provided in order to achieve extreme dynamic range, so that rarely occurring weak signals can be detected and distinguished from noise.FWATD can track and correct for temperature-dependent baseline (DC level) fluctuations, which may otherwise lead to incorrect detection or even detection of false pulses. It supports several types of noise reduction for both random and systematic noise. The flexible architecture and user-defined settings enables tailored noise reduction for various applications.
-
Product
Illumination
-
*Illumination units for contour and position verification*External LED illumination for contour / pattern match sensors*Permanent light or pulse operation*White light, red light and infrared versions*Compact and robust housing
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Guided Wave Radar
-
A top-down, direct sensing technology that uses low-energy microwave pulses sent down a probe to accurately detect the boundary between two immiscible liquids.
-
Product
High Voltage Pulse Generators
-
Berkeley Nucleonics Corporation
Designed to provide precision control over the output waveform to enable process optimization for research and industrial customers.
-
Product
Pulsed Fiber Amplifier
MOPA
-
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
Product
Single Shot Third-order Cross- Correlator
Rincon SS
-
Specifically developed for measuring a wide array of output parameters from ultrafast laser systems including: contrast ratio of laser pulses, determining pulse pedestal, pre- and post-pulses, and amplified spontaneous emission in femtosecond systems.
-
Product
Miniaturized AC Servomotor
-
Citizen Chiba Precision Co., Ltd.
*Use of Nd magnets allows excellent responsiveness and high output in a compact size.The rotor is evenly balanced to suppress mechanical vibrations.Uses slotless coils which prevent cogging and allow smooth revolutions, even at low speeds. *Miniaturization and inclusion of a high pulse encoder means highly precise positioning is possible.
-
Product
Time Interval Shaper
CH7-316
-
The Ch7-316 time interval shaper is designed to generate pulse sequences coherent with the reference signal (internal or external) with a wide range of repetition periods, as well as two pulse sequences with a period of 1 second (time scales) with a programmable phase shift.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Optical Components for Custom Spectroscopy
-
HORIBA offers a wide variety of optical accessories. We have optical choppers which pulse continuous light sources. Explore our order sorting filter wheels for spectrographs and monochromators. Choose from our optical fibers and light guides, with flexible light delivery, single fibers, fiber bundles, and liquid light guides. And select from our lens and mirror-based sample compartments.All of these accessories are compatible with our various optical components. Our optical accessories allow us to complete a custom solution for your unique configuration requirements and a variety of spectroscopy applications. HORIBA offers more choices to ensure you can select the best optics for your needs.
-
Product
Integrated Potentiostat System
ER466
-
The ER466 Integrated Potentiostat System is our most popular potentiostat model, being ideal for cyclic, linear sweep, and most analytical pulse voltammetric experiments, either in the research or teaching laboratory. It also functions as a galvanostat, ZRA (zero resistance ammeter), and high impedance voltmeter (electrometer).
