Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
Cable Sheath Fault Location
-
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
Product
Pathfinder Locating System
The STICK™
-
Built with Pathfinder SAF Technology™ at its core, the Stick offers RYCOM’s most ophisticated technology in an economical package. Pathfinder SAF Technology™ is the heart of our premium locators, now RYCOM is applying this proven technology throughout the entire product line. From crowded easements, to long runs of pipe, to the most demanding of locating environments, users can depend on The Stick. Dependability is not only driven by the internal technology, but The Stick is built to last with an aluminum housing and sealed against weather. The ruggedly designed and well balanced receiver includes an LCD screen providing relative and actual signal strength, as well as a speaker for variable audio pitch. A peaking signal response allows the user to minimize interference and maintain the locate on the target conductor. The Stick cable and pipe locator offers multiple active frequencies — from 50Hz to 82kHz — ensuring flexibility to match the needs of the most complicated locating environments. Transmitter functions include transmitter induction, coupler induction and direct connection. Whether the locate is measured in feet or miles, with automatic impedance matching from 5 ohm to 25,000 ohms and 3 watts of output power, The Stick will meet the challenge. Rycom Instruments®, Inc. locators are designed and manufactured to make utility locating as accurate as you need and as simple as you want.
-
Product
Under Ground Cable Fault Locator
-
Widely used in electrical and power generation sector for testing underground cables in order to detect any fault.
-
Product
Precision Locator
MXL4
-
The MXL4 is a high performance multi-frequency Precision Pipe & Cable Locator. In-built Data Logging as standard. Bluetooth™ connectivity and GPS tracking options available. Designed for use with an MXT4 Multi Frequency Transmitter. Network Rail Approved.
-
Product
Ground Fault Locator
K-3837
-
Kongter Test & Measurement Co., Limited
Kongter’s K-3837 Ground Fault Locator is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems with earth fault. It will save you from long time unnecessary troubleshooting and helps to increase the stability of your electrical equipments. It is widely used in various DC systems including power utilities, locomotive, telecom and etc.
-
Product
Metal Locator
F-90M
-
The F-90M is the professional's choice for locating buried valve boxes and covers.The F-90M detects buried metallic objects such as meter boxes, valve boxes, and manhole covers. Ferrous metal objects can be detected more than a foot beneath the surface, and their presences are indicated by both an addible tone and meter deflection.
-
Product
Wire Harness Tester
NX Solo
-
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
-
Product
Cable Locator (LCD type)
5500 CB
-
Standard Electric Works Co., Ltd
● The 5500 CB transmitter is a great tool for locating and identifying cables and individual conductors. ● Designed for locating unenergized cables and powered cables. ● Voltage measurement for cables : ACV 12V~300V DCV 12V~300V ● Signal Transmission • Transmission Power Level Selection (includes 1, 2, 3) • Transmission Signal Code Selection (includes F, E, H, d, L, C, O, A) ● Flashlight & Back Light function.● The Silent Mode (Disable Button Beep).● The Level Bar Display on the LCD Screen (the transmission power level indication).● The Action Wave Display on the LCD Screen (when the signal is transmitted).● Auto power off function.
-
Product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
Product
Pen-based Fault Locator
-
*Find the breakpoint, bending or cracking*Find the fault of OTDR dead zone*Identification of fiber from one end to other end*Universal adaptor*Testing distance up to 8km*Lightweight, red laser output, both SM and MM available
-
Product
Hazardous Location Syringe Pump
260HLf
-
Teledyne LABS HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
DB9 DIN-Rail Wiring Board
ADAM-3909
Terminal Block
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with DB9 connectorCase dimensions (W x L x H): 77.5 x 45 x 51 mm (3.1" x 1.8" x 2.0")To Be Used With PCI-1714U/UL, PCL-728, PCL-740, PCL-741, PCL-743B, PCL-745B
-
Product
Wire Mount Testers
-
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
Utility Locator
UtilityScan
-
Geophysical Survey Systems, Inc.
UtilityScan® provides a rich feature set that redefines the level of performance available in a low cost utility locating system. The newly designed UtilityScan combines nearly two decades of utility designation experience with today’s most innovative technology. The UtilityScan features a wireless and lightweight configuration, our patented HyperStacking technology and integrated LineTrac system. This state-of-the-art system sets the new standard in performance and price.
-
Product
Board Fault Locator
SYSTEM 8 (BFL)
-
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
Product
Pre- Locator
CFL PL2+
-
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
Product
Mobile Problem Locator
MPL
-
The ComSonics Mobile Problem Locator (MPL) application is a smart phone application designed to provide cable technicians with a simple tool to help maintain their network. Targeted for use with ComSonics' QAM Compass via Bluetooth connection to provide contractor work verification.
-
Product
Fault Locator
REZAP MODULAR
-
REZAP MODULAR brings full REZAP functionality to fuse panels with severe space restrictions
-
Product
Thumpers and Cable Fault Location
-
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
Product
Cable Locators, Route Tracers And Height Meters
-
CHM cable height meters are easy to use, handheld devices which use ultrasound to determine the height of up to six overhead cables and wires. They are designed to measure cable sag, overhead clearance and cable heights up to 23 m, with separate products dedicated to the power and telecommunications markets. As a safe alternative to telescopic ranging sticks, there is no physical connection to the cables.
-
Product
Pipeline & Cable Fault Locator
TM2000
-
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
Hipot Wire Harness Testers
NX Hipot
-
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
Product
DB9 To 10-Pin Wiring Board
OPT1-DB9E
Terminal Block
DB9 to 10-pin wiring boardDimension: 35 x 42 x 20mm
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
Fault Locator
VM-510FFL+
-
Finding the location of an underground cable fault just became easier with the VM-510FFL+ Standalone A-frame locator. Now locating a suspect cable and finding the fault can be done with the VM-510FFL+ and a compatible transmitter. There is no longer a need for a separate utility locator with cables connecting to it. After connecting a compatible transmitter to the line and placing it in a Fault-Find mode, use the simple to operate four button controls of the VM-510FFL+ to locate and stay on the cable path while pinpointing the sheath or ground fault.
-
Product
Glow Wire Test Apparatus
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Control Wires Surge Suppressors
AS-8SP / AS-12SP / AS-16SP
-
Array Solutions Control Wires Surge Suppressors
