Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
Handheld Visual Fault Locator(VFL)
JW3105N
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3105N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
Product
4 Wire Earth Resistance & Resistivity Tester
4236 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.● Optical USB to RS-232 data transmission.● The stored data can be transferred to a PC.● 2 optical LEDs are built-in for data transfer.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Signal, Module, Receiver, CASS, 210 Position, Discrete Wiring
510113125
Receiver Module
Module, Receiver, Cass, Signal, 210 Position, Discrete Wiring
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
ITA, G18, 18 Module With Discrete Wiring And PCB Capability
410120101
ITA
ITA, G18, 18 Module with Discrete Wiring and PCB Capability
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Wire Tracers & Underground Locators
-
When you want to make absolutely sure you’re digging in the right place, depend on the technology leader: Amprobe. Known for speed, reliability, and accuracy, Amprobe Wire Tracers and Underground Locators will help you get your job done efficiently. Whether you’re looking for a wire (energized or de-energized) in a wall or ceiling, or want to locate buried utilities before you dig, you can depend on Amprobe’s best tracers to help you get the job done quickly.
-
Product
Post Wire and Die Bond Inspection Machine
IV-E1700
-
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
-
Product
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator
910104126
Crimp Die
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator.
-
Product
Service Drop Locator & Metal Detector
VM-585
-
The VM-585 is a combination of the popular VM-550 utility locator with the added benefit of a built in Ferrous Metal Detector. This makes it ideal for locating short distance runs such as service drops and to detect buried ferrous metal objects such as buried valve box covers, buried tanks, and manhole covers. The advanced filtering of the VM-585‘s metal detector rejects materials such as bottle caps and aluminum cans and zeros in on finding only ferrous materials. The manual gain control allows it to be controlled and able to work close to large metal objects such as automobiles and chain link fences while still looking for the targets underground. The VM-585 will locate through asphalt, concrete, or grass and in temporary conditions such as snow.
-
Product
Fault Location
-
Specialized testing equipment and methods used to detect, identify, and pinpoint damages, breaks, or lengths in laid cables and conductors.
-
Product
Wire Probe Needles Materials & Pin Diameters
-
Advanced Probing Systems, Inc.
Tungsten pins and tungsten-rhenium pins can be provided with either nickel plating or silver plating. Beryllium-copper pins are supplied with a silver plating coating.
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
16 Channel Multiplexer (2/4-wire) Module for 34970A/34972A
34902A
Multiplexer Module
The Keysight 34902A module for the 34970A/34972A Data Acquisition/Switch Unit employs reed relays to achieve scan rates up to 250 channels-per-second. Use this module for high-throughput automated test applications as well as high-speed data logging and monitoring tasks.
-
Product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
-
LampChek indicates the lamp and fixture continuity.
-
Product
Pull-Thru Adapter, Wired, for Pickering 40-161-101
510140177
Pull-Thru Adapter
Pull-Thru Adapter, Wired, for Pickering 40-161-101
-
Product
650nm Visual Fault Locator
-
Shanghai Baudcom Communication Device Co.,Ltd.
Visual Fault Locator series Visual Fault Locator uses the DFB-LD as the emitting component. Driven by constant current source, the indicator can emit stable red laser.The product can be used to inspect fiber failure when they connect with optical interface and be inserted into single mode or multi mode optical fiber.It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.
-
Product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
-
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
Product
Pen Style Visual Fault Locator
CARY-VFLXX
-
The CAWI-VFLxx Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network duringand after installation.
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Drawing Die And Wire Measurement
Drawing Die Inspector DDI
-
Optik Elektronik Gerätetechnik GmbH
Special microscope setup for visual inspection of wire drawing dies.
-
Product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
ITA Module
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
Benchtop Wiring Analyzer
2115
-
The Model 2115's compact size makes it the ideal choice for many benchtop or portable test applications. The small size does not mean you sacrifice any functionality. The 2115 delivers a full 1500 volt isolation and 2 amp continuity test stimulus. With the optional AC breakdown test providing 1000 VAC test stimulus, you will meet all test requirements.
-
Product
Wire Systems Analyzer
Console Test Systems (CTS)
-
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
Product
Telephone Wire Cable Tester For Testing Continuity With Sender And Receiver
PHCT55
-
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
Product
Metal Box Locator
P500
-
Although originally designed to accurately locate valve boxes and manhole covers, the Elcometer P500 Metal Box Locator can also be used as a general metal detector.
-
Product
Utility Locator
VM-850
-
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-850 operates at a much lower frequency of 9.82kHz which is ideal for smaller diameter utilities such as CATV, power and telephone with less bleeding onto adjacent services.
-
Product
Ground Detection and Earth Fault Location Equipment for Ungrounded or Floating DC Systems
ZX3
-
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
