-
Product
Motion Based Waves
-
Accurate Motion Based wave measurements are critical in applications such as offshore wind farm development, navigation, cable laying, breakwater building, and bridge construction.Waves also result in continuous loads on marine structures, including docks, moorings, and offshore platforms.Motion Based Waves are challenging to measure. Variables to consider when collecting wave data include the depth of the measuring device, proximity to shore, wave types, and available infrastructure from which to measure.Several methods for measuring motion based waves are available, and careful selection of the best approach is needed to get the optimal result.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Microwave Amplifiers
MShU Series
-
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
Product
Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
RF Benchtop / EMC Amplifier
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
Miniature Amplifier PCB
-
Sized for single channel TO-5 packages and electrically compatible with all Dexter Research Center detectors. Available in three amplifier gains: 300, 500 and 1,000 providing convenient buffering and pre-amplification of thermopile signal. Facilitates fast R&D startup time that can be integrated into your prototypes or final system design.
-
Product
Telecom Optical Amplifiers
-
Thorlabs' optical amplifiers for telecom applications are available as complete benchtop systems or as pigtailed butterfly packages. Our line of benchtop optical amplifiers includes a praseodymium-doped fluoride fiber amplifier (PDFA) and erbium-doped fiber amplifiers (EDFAs). Our optical amplifiers available in pigtailed butterfly packages include InP/InGaAsP or GaAs/InGaAs semiconductor optical amplifiers (BOAs or SOAs), and high-speed optical switches.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
-
Product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
-
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
-
Product
RF Amplifiers up to 500 MHz
-
Narrow and Broad band RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAsFET in Class A and Class A/B topologies for AM, FM, VHF, and UHF bands with output power ranging from 0dbm to 60dbm.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
Driver Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
Point on Wave Synchronous Test Sequencer
-
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
Product
DSP And Power Amplifier
DMPA12
-
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
Product
Analog Distribution Amplifier
DA 1:54
-
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
Product
Transimpediance Amplifiers
-
The UDT TRAMP products are transimpedance amplifier (current-to-voltage) instruments that provide a low input impedance to accurately measure the short circuit current of phototransducers such as silicon and germanium photodetectors, vacuum photodiodes and photomultiplier tubes. The range includes the economically priced TRAMP, and for ultra precision and accuracy, the TIA-3000.
-
Product
Wave Profiler Fixture
KIC® Wave Surfer™
-
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
Product
RF Amplifier
SA1012
-
Hangzhou Softel Optic Co., Ltd.
*Forward path use import low noise push pull amplify module or GaAs push pull module,2 Power-Double module or GaAs amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, It's distortion is little and SNR is high.*It is more convenient to debug because of plug-in(or adjustable) duplex filters, plug -in fixed(or adjustable)equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
Pressure Based Waves
5218
-
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Pneumatic Contact
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Power Amplifiers
-
RPG Medium Power Amplifiers are developed and manufactured by using most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 130 GHz. With improved DC-supply and modern semiconductors these medium power amplifiers not only deliver high power output but also superior power added efficiency (PAE) and higher linearity. These medium power amplifiers are available as a standard product and on request as a customized manufactured product..
-
Product
Tube-To-Tube Gravity Handler
Rasco SO1000
-
The SO1000 test handler’s mature design and high reliability it provides excellent cost of test. Highly flexible as a result of a broad range of device kits can be combined with various Sensor and MEMS applications.Featuring a fast plunger with up to four plunger heads for high speed and high throughput with index time down to 500 ms. Available in single, dual, and quad configurations.
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
Trip Amplifiers
-
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
