-
Product
Current Feedback Op Amplifiers
-
Analog Devices high speed (> 50 MHz) current feedback op amps enable you to operate at higher speeds. Current feedback op amps traditionally have wider bandwidths and higher slew rates than voltage feedback amplifiers and do not feature a gain bandwidth restriction associated with voltage feedback op amps.
-
-
Product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
-
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
GaN Amplifiers
SBP-3233831838-KFKF-E1-HR
-
Model SBP-3233831838-KFKF-E1-HR is a power amplifier with a typical small signal gain of 18 dB and a nominal Psat of +38 dBm across the frequency range of 32 to 38 GHz. The DC power requirement for the amplifier is +30 VDC/2 A. The mechanical configuration is an inline structure with K(F) connector as its input port and output port. Other port configurations, such as K connectors and WR-28 waveguides for either the input or output, are also available under different model numbers.
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
DC-AC Sine Wave Inverters for Ultraviolet (UV) Lamps
UV Lamp Inverters
-
The sine wave inverters are designed and built to meet any customer input/output and mechanical configuration requirements.
-
Product
Power Amplifiers (MCPA)
-
*Multi-Carrier Power Amplifier supplies an additional 12.9 dB of Gain at high power*Supports iDEN in the 850MHz Band, available for GSM in cellular and PCS configuration*High power handling with low IM and insertion loss*Ideal for combining multiple BTS to a single feeder line and providing increased power to the antenna
-
-
Product
Mini Pneumatic, Contact, Receiver, Push-in Fitting, for 6 mm OD Tubing
610131112
Pneumatic Contact
Primary mating contact 610132112.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
Product
Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um
AKSM13(A)-40
-
Model:AKSM13(A)-40 Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um Details&Spec: Please refer to KSM13(A)-40 Specification,It is combinated by 2pcs KSM13(A)-40 (C,SR,SL) and 1pc KSM13(A)-40CZ(as vertical stage)
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
Product
Ultra High 1.16 (33.00) - 9.70 (275.00) Long Travel Bead Probe
BPLT-25HL-9.7
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
Single Channel High Voltage Linear Amplifier
A600
-
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
Pulsed Fiber Amplifier
MOPA
-
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
HF Amplifier
Prometheus
-
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Product
Profiling Current Meter and Wave
SeaGuardII DCP Wave
-
The SeaGuardII DCP Wave is a 600kHz Doppler Current Profiler able to measure directional wave parameters and currents from a bottom mounted installation.The Acoustic Wave software 5759 used by the DCPS implements unique features to improve the wave measurement accuracy by optimizing the signal to noise ratio.Maximum deployment depth is 40m in normal scatter conditions. The Profiling Current Meter and Waveis available as a self-recording instrument. It can be easily integrated into a real-time system offering reliable two-way communication.
-
Product
Intelligent Silicon Photomultiplier Tube
i-Spector family
-
i-Spector is a all-in-one detector and electronics instrument based on a SiPM area (18×18 mm2, 24×24 mm2 or 30×30 mm2), possibly coupled to a scintillation crystal suitable for the chosen application. The i-Spector integrates in a compact tube-like mechanics the detection stage, frontend electronics, an integrated power supply for SiPM biasing and, eventually, a digital chain to process onboard the incoming data. The i-Spector can be controlled via Ethernet and/or wireless communication based on LoRa standard.
-
Product
System Amplifier
-
Solid state Broadband Amplifiers are designed for optimum operation for IED Jammer Applications which is featured as below. We can rack mount any of our existing amplifiers or systems or custom design the amplifier and enclosure. Each Rack Mounted Amplifiers are built around a large bonded fit heat-sink rated for high temperature ambient operation.
-
Product
Phantom Vent Tube Metal Detector
-
The Phantom Vent Tube metal detector is primarily designed to detect and track a fallen vent tube nozzle inside a bottle that is conveyed through bottle-processing equipment. The convenient retrofit design allows for easy installation into existing bottling lines. Built from stainless steel (304) material and totally enclosed for washdown purposes, the detector phases out the conveyor belt and maintains a steady sensitivity.
-
Product
Mini Pneumatic, Contact, ITA, Push-in Fitting, for 4 mm OD Tubing
610132111
Pneumatic Contact
Primary mating contact 610131111.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
Product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Pneumatic Contact
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Single Channel High Voltage Linear Amplifier
A400
-
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
-
Product
Distributed Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support distributed amplifiers that provide a simple and easy solution for a wide variety of commercial and aerospace & defense applications. MACOM’s distributed amplifier family cover frequencies from DC to 80 GHz and are offered in both bare die and air cavity packages. These devices offer an excellent combination of broadband performance and ease of use for a variety of high-performance applications.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
