Filter Results By:
Products
Applications
Manufacturers
Dark Field
-
product
Imaging & Analysis
Microscopes offered by Buehler generally fall into the categories of stereo microscopes, upright microscopes, or inverted microscopes. Inverted microscopes are commonly referred to as metallurgical microscopes. Microscopes may offer episcopic (reflected light) observation, diascopic (transmitted light) observation, or both possibilities. Illumination may be delivered in bright field mode (BF) or dark field mode (DF), and several techniques such as differential interference contrast (DIC) and polarized light microscopy make use of the nature of light to reveal specific pieces of information when studying materials.
-
product
Camera Module Tester
Evolusys Technologies Sdn. Bhd.
• Lens Focusing plus Far Field Sharpness Testing - CTF/MTF/SFR• Near Field Sharpness Testing - CTF/MTF/SFR• Flat Field Grey Image Testing - Optical center, Defect pixels, particles, blemish, shading, color shading, color ratio, SNR, etc.• Dark Field Image Testing - Hot pixels, dynamic range, SNR, etc.• Current Measurement - Active, standby
-
product
Optical Microscopy
Rocky Mountain Laboratories, Inc.
Optical microscopy from 1X to 1000X is achieved with a variety of microscopes. Images can be formed in bright field, dark field, and differential interference contrast (DIC or ‘Nomarski’) modes. Optical microscopy anlaysis is often used before any other techniques to document samples. Color and morphology are important clues in materials identification.
-
product
HDMI Camera
TrueChrome IIS
Fuzhou Tucsen Photonics Co.,Ltd
TrueChrome IIS automatically analyzes the acquired images andoptimizes the white balance, exposure time and saturation, to present perfect images. Whatever for bright field bio imaging or dark field birefringent crystal imaging, TrueChrome IISdelivers ideal images, barely needing any parameter adjustment.
-
product
Field meters
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
product
The Field Logger
The Field Logger is a stand-alone data logger which is capable of recording potential vs. time and LPR vs. time data. The instrument is battery powered and records data onto an attached SD memory card. The instrument is entirely contained within a waterproof (IP67), tough polycarbonate enclosure (23x19x11cm), with probe connection via a single high quality watertight Lemo or Amphenol connector.
-
product
Field Testing
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
-
product
Magnetic Field Visualization
mageye
Our mobile "magnetic field sensor" allows you to visualize and evaluate magnetic stray fields. Our mageye, matesy’s miniaturized magneto-optical USB microscope, provides information about the magnetic fields on the surface of a wide variety of samples with resolutions in the micrometer range.
-
product
Field Comm Analyzer
S5800H
S5800H Series Field Comm Analyzer is an 8.4 inch large touch screen instrument which is designed specifically for wireless communications field engineers and technicians. S5800H series provide all necessary measurement functions and performance to accurately characterize the signal environment in addition to clearing, detecting, identifying and locating signal interferenc.
-
product
Field Measurement Sensors
High frequencyElectromagnetic field measurement sensorsLow a frequencyElectric field measurement sensorsMagnetic field measurement sensors
-
product
Far Field Scanner
2201
The 2201 Far Field Scanner provides high speed, high dynamic range measurement of the mode field diameter and effective area of single-mode fibers and the numerical aperture of multimode fibers using direct far field scanning, the ITU reference technique.
-
product
Field Performance Analytics
Monitor manufactured products performancein the market to increase customers satisfactionand reduce warranty costs with QualityLine’sfield products performance analytics
-
product
Field Meter
AP 301 FULL HD
The AP301 FULL-HD is a field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
Probes, Magnetic Field
EM-6882 | 20 MHz To 230 MHz
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
product
Field Meter
AP01
The AP01 is a field meter with full coverage of terrestrial TV bands, cable (CATV), satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
Field Ttesters
Our product range comprises from small handheld, battery fed testers to full featured service performance assurance tools and distributed monitoring systems. We have several product lines including:QoS / SLA verification system Ethernet, IP, Critical Data, VoIP, IPTV .Hand-held testers: Gigabit Ethernet, Synchronous Ethernet, E1, PDH, SDH, Ethernet, IP, Jitter, Wander, Datacom, Frame Relay, etc.
-
product
Field Communicators
We offer modular multi-bus field communicators for HART, FOUNDATION Fieldbus H1 and Profibus PA protocols, combined in some of our process calibrators. While the communicator is built in the same device with the process calibrator, they can communicate seamlessly offering better user experience than separate calibrator and communicator. Plus you only need to carry one device. Thanks to the modularity you can select which protocol you take, and update more protocols later on, if needed.
-
product
Near Field Probes
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
product
Magnetic Field Meter
MP - 2000
The new magnetic field meter MP - 2000 first used probes (tangential and Axialfeldsonden), in which an own microcontroller, the analog sensor signals are digitized and linearized directly in the probe. This new technique is extremely trouble-free and allows very precise measurements, especially at high magnetic field strengths, where Hall probes can not operate linearly.
-
product
Pulsed High Field Magnetometer
TPM
This is the equipment evaluating the magnetic properties of rare-earth such as Js, Jr, Hcb, Hcj, (BH)max, HK and SR etc.
-
product
Field Portable Wire Analyzer
Model 2635
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
product
Miniature Magnetic Field Sensor
FLC 100
Complete miniature fluxgate magnetometer can be used in any application where the sensitivity of Hall- or MR-magnetometers is not sufficient, e. g. measurement of the earth's field, detection of AC field from power lines, vehicle detection, compass navigation, and many others. Due to its low price and low power consumption ideally suited for multi-sensor array systems.
-
product
Field Strength Analyzer
SRM-3006
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
product
Field Probe Positioner
The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.
-
product
Magnetic Field Scanner
MAGNET-PHYSIK Dr. Steingroever GmbH
Magnetic field scanners measure the magnetic field around permanent magnets or magnetic systems. The results can be output as a colored 2D, 3D representation or as a table.
-
product
Rugged Field Test Set
MTS-207
The MTS-207 is a state-of-the-art portable PXI platform for field testing and data acquisition systems. Its proven architecture has been deployed worldwide on multiple programs including the MTS-206 Maverick Missile system flight line tester, the MTS-209 Common Armament Test Set, the AN/TSM-205B Hellfire System test Set, and many more. It combines the capabilities of the versatile and powerful PXI architecture in a compact, ultra-rugged, flightline qualified enclosure. The MTS-207 is ideal for test and data acquisition applications requiring operation under harsh environmental conditions including flightline, back-shop, or airborne applications.
-
product
Field Strength Calibration Probe
Beijing KeHuan Century EMC Technology Co,.LTD
Three-axis omnidirectional 100kHz～6GHz light transmission.
-
product
Digital Static Field Meter
Model 715B
- Assess electrostatic fields or charge on objects- Measures up to ±19.99 kV at a distance of 1 inch- Accuracy of <±5% in both normal and ionized environments- Uses a chopper stabilized sensor- LED ranging lights for positioning the meter at the right distance- Zero function allows the display to be adjusted to zero (0)- Hold feature to lock the reading on the display- Low battery indicator on the display- 1-year limited warranty
-
product
Field Strength Meters
FIM-22 And FIM-41
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their hinged covers, on the rugged drawn aluminum cases, contain a loop antenna. Opening the cover to a vertical position connects the antenna terminals to the receiver via maintenance-free gold-plated contacts. An interlock switch prevents inadvertent battery discharge when the cover is closed.
