Mixed Signal Testers
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, MIxed Signal Test Systems
-
Product
Multi-Battery Tester
MBT-1
-
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Product
Insulation Tester
CENTER 365
-
Insulation Test Range Up To 20GΩ, Test Voltages Of 50V, 100V, 250V, 500V and 1000V For Insulation Test, >1mA Short-Circuit Test Current For Insulation Test, Live Circuit Detection
-
Product
30MHz Arbitrary Waveform Signal Generator
Model AWG30D
-
- 4.3′ High Resolution TFT LCD Display- Two Independent Channels Output, Same Characteristic- 1μHz Frequency Resolution for whole range- 120 MSa/s Sampling Rate, 14 Bits Vertical Resolution- 5 Standard Waveforms, 50 Built-in and 5 User-defined Arbitrary Waveforms- FM, AM, PM, PWM, Sum, FSK, BPSK and SUM Modulation, Sweep and Burst Function- Channel Coupling and Combine Features On CHB- Build in 350MHz Frequency Counter- Arbitrary Waveform Edit PC Software- Standard Interface: USB Host, USB Device and RS-232
-
Product
PXI Mixed Configuration Relay Module - 4 Cells Populated
40-138-AA-BB-CC-DD (4 CELL)
Relay
The 40-138 2A Relay Module with 4 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
-
Product
Temperature Testers
-
UEi Test & Measurement Instruments
A unique combination of features including logging capabilities with 9,999 memory positions and a USB interface and software, one, two and four inputs offering relative and differential readings
-
Product
Insulation Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Testing the integrity of insulation requires measuring its resistance to current flow across it. A high level of resistance means that very little current is escaping through the insulation. Conversely, a low level of resistance indicates a significant amount of current may be leaking through and along the insulation.
-
Product
DMX Tester
DMXter4 RDM
-
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
Product
Adjustable Signal Samplers
7998
-
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
Product
Mixed Signal Oscilloscope: 20 GHz, 4 Analog Plus 16 Digital Channels
MSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
PAT TESTER
-
Precision Mastech Enterprises Co.
The Safety Pat Plus is a handheld battery powered unit suitable for carrying out electrical safety tests.Stores 300 test results and can be battery & mains powered. The instrument is capable of testing surge protected equipment & can test 110V, 230V appliances. It will return true leakage results at both 110V and 230V
-
Product
Surge Testers
MTC 2
-
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
Product
Folding Tester
DRK111B
-
Shandong Drick Instruments Co., Ltd.
DRK111B Folding Tester is designed according to relevant standards and adopts modern mechanical philosophy and computer processing technology. It has LCD display function, various parameters setting function, conversion, adjust, memory, printing, and other functions.
-
Product
Torque Tester
DI-9M-8/08
-
Ideal for daily inspection of electric screwdrivers. Uses OW joints that do not require rewinding. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement without rewinding by "OW joint".
-
Product
Cable Testers
E447
-
Similar to E445 but without jack and RCA (phono) testing facilities. Includes special XLR remote unit to enable testing of cables where it is not possible to bring both ends to the tester.
-
Product
VDSL2 Tester
-
TM-600 VDSL tester specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on.
-
Product
Signal Generator
8004
-
5 digit BCD, 1 latch control line, 25 pin female, D type connector. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
-
Product
SAT/CATV/TV Signal Analyzer
DSA 1491
-
9” full-color, high-resolution touch screen user interface simplifies complex measurement tasksRF inputs including satellite, cable and terrestrial along with ASI and IP inputsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
Product
Cellular Signal Analysers
SNYPER Family
-
2G, 3G and 4G LTE cellular signal analyser range - including Spectrum 'livescan'. The SNYPER is a sophisticated yet easy to use range of cellular signal analyser comprising 2G and 3G versions with LTE family Now available.
-
Product
Low Frequency Vibration Signal Conditioner
-
A compact Signal Amplifier to make optimal signal processing being connected with the Servo type Accelerometers. It is used for Vibration Acceleration Measurement, Waveform Observation, for various Analysis in combination with the AC Voltage Meter, Oscilloscope, FFT Analyzer respectively. Furthermore, Voltage signals from the Microphones or Sound Level Meters can be output to the instruments like Recorders along with the Vibration Signals.
-
Product
Pulse Signal Amplifier
VCH-606
-
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
Product
Burn-In Tester
-
Universal test bench system. Provides basic electrical measurements at a low cost. Designed for a wide range of electronic products with a dedicated wiring harness. Allows you to expand the scope of functionality. Work in automatic or manual mode. Tailored to the needs of low- and high-volume production
-
Product
Video Signal Generator
MSPG-4600MT
-
MSPG-4600MT is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV (NTSC, PAL), as well as V-Chip (Violence Chip) function to block the violence and sex etc. bad program to protect a person under age through the regulation grade.
-
Product
Bump Tester
KD-163
-
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
Product
Signal Generator
SGA3
-
The C.Scope SGA3 is an affordable Signal Generator designed for use alongside a CXL3 or DXL3 Cable Avoidance Tool to make the task of cable avoidance far more effective.
-
Product
Scratch Tester
-
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
Product
Salinity Testers
-
Labodam pocket salinity testers are equipped with platinum sensors, providing fast and reliable results measuring the salinity of water and other low and high salt concentrated solutions. Equipped with replaceable electrodes, helping to reduce maintenance cost.
-
Product
Circuit Tester
69105
-
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
Product
RF Signal Generators
-
Compact and reliable microwave and RF Signal Generators for use in automated testing environments, production verification, EMC testing, educational institutions, aerospace, defense projects, LTE engineering, satellite communications, CATV, 5G design…
-
Product
Cable Tester
-
WEETECH offers a number of individual testers for the low voltage open test and short test.
