Mixed Signal Testers
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, MIxed Signal Test Systems
-
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
Digital Hardness tester
THL270
-
Pen type Leeb hardness tester Converts to all common hardness scales (HL.HV,HB,HRC,HRB,HRA,HS). The machine also include interface to connect with impact device C, DC, G, D+15, DL
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Universal Cable/Harness Tester
LX-680
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The maximum test spot is 256.
-
Product
Insulating Oil Tester
OTSA series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Tests as per international standards• Auto / Manual mode• 100 test result storage capacity• Large LCD display• Built in printer• User Friendly RS 232 Interface• Safety protection• Accurate performance
-
Product
Mixed Signal Oscilloscope 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054G
Oscilloscope
The MSOX3054G 500 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Impulse Spark Tester
IT-25B
-
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Product
CT Tester, Meter Tester, Circuit Analyzer
GOLD MINER IV
-
Gold Miner is the first device of its type to test the electricity meter using exact, simultaneous measurements made on all primary and all secondary phases of the circuit. Perform in-service meter testing with a combined 3-phase load, or a single-phase load. Gold Miner not only displays the Meter’s accuracy, but also the overall, true accuracy resulting from the CTs + Meter combination for your entire measurement circuit.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Leak Testers
-
Vidac has installed various versions of Leakdown testers for products such as:ValvesSealsConduit fittingsExplosion-proof cases
-
Product
Mixed Signal Oscilloscope - 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX4104A
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Multi-Operational Surge Tester
MB Model
-
Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.
-
Product
Opticle Encoder Tester
Endeavour
-
Evolusys Technologies Sdn. Bhd.
The Endeavour test system is a complete solution for testing optical digital and analog encoders for electrical and functional test with high accuracy and high speed. It provides high precision, research-grade electrical and functional testing and signal characterization suitable for encoder development. For quality assurance in encoder production, the Endeavour can be easily combined with a handling system for automated, high-end testing and qualification in the production of encoders.
-
Product
DIN Abrasion Tester
TF215
-
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, leather etc. Abrasion Testing Machine complies with DIN 53516, ISO 4649, BS-903,etc.
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
Earth Tester
TAURUS PRECIOHM ET
-
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Product
Robotic ESD Tester
SmartZap
-
The SmartZap is a fully automated zap gun tester with automatic failure detection capability, providing far superior performance than manual zap gun test. It is complying IEC61000-4-2 test standard.
-
Product
60204 Safety Testers
-
For testing the electrical safety of machines and devices according to the machinery directive EN60204 and VDE113.
-
Product
Oxygen Permeability Testers
-
Oxygen permeability is the ability of a barrier material to oxygen to permeate through it in a specific time. Oxygen permeability may vary with temperature, humidity, pressure and specimen thickness.
-
Product
Twist Tester
TY370
-
TESTEX Testing Equipment Systems Ltd.
Yarn Twist Tester, to determine yarn twist in single or plied yarns, quadrant type with auto stop & reverse for conventional or untwist/re-twist methods. Twist Tester Machine complies with ISO 2061, ASTM D1422/1423, BS 2085,etc. Twist test is very important in textile testing. Our Yarn Twisting Machine price is also competitive.
-
Product
Vibration Testers
-
Lansmont’s Vibration Test Systems are simple to operate safely and can perform a wide range of vibration tests in accordance with government, industry and corporate specifications.
-
Product
Signal Analysis
Histograph
-
The Histograph software is used for statistical signal analysis: finding the statistical values characterizing the signal and building the theoretic histograms based on the data obtained.
-
Product
Impact Tester
-
The impact tester is used for testing the impact resistance of materials, to determine their quality under dynamic load conditions.
-
Product
Electromagnetic Field Tester
-
The EMF tester is designed to provide user a quick, reliable and easy way tomeasure electromagnetic field radiation levels around power lines, home appliancesand industrial devices.
-
Product
Capacitance Tester
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
Is a piece of electronic test equipment used to measure capacitance, mainly of discrete capacitors. Depending on the sophistication of the meter, it may display the capacitance only, or it may also measure a number of other parameters such as leakage, equivalent series resistance (ESR), and inductance. For most purposes and in most cases the capacitor must be disconnected from circuit; ESR can usually be measured in circuit.
-
Product
RTM Analog & Discrete Signal Conditioning Board
-
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
Product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
Product
Motor Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
