Voltage Calibrators
An accurate voltage units of measure to facilitate comparison to and adjustment of instruments.
See Also: Voltage Sensors
-
Product
Single Channel High Voltage Linear Amplifier
A800
-
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Low Voltage Switching Regulators
-
Renesas' comprehensive portfolio of low voltage, synchronous buck integrated FET switching regulators offer a compact solution size with outstanding performance.
-
Product
Power Calibrators And Power Quality Calibrators
-
Calmet Smart Calibration Devices
A power calibrator and a power quality calibrator are both specialized instruments used to verify and adjust the accuracy of other instruments, but they focus on different aspects of electrical power.
-
Product
Voltage Input Device For FieldDAQ
-
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Calibration Management Software
MET/CONNECT™
-
Calibration Management Software through Fluke Calibration MET/CONNECT™ Qualer is a premier asset, maintenance and calibration management system providing a pre-configured, business-in-a-box, best in class, software solution for progressive companies. Fluke Calibration’s MET/CAL® is the leading calibration automation software platform, allowing calibration labs to harness the power of thousands of automated procedures. Qualer and MET/CAL® can now be connected through Fluke Calibration's MET/CONNECT™ integration app. This enables labs to leverage the power of MET/CAL® procedures and provide the results seamlessly to Qualer as their system of record. Qualer's partnership with Fluke Calibration and MET/CONNECT™ provides a seamless way to integrate the two platforms and bring the benefits of automated calibration into the Qualer platform.
-
Product
Medium Voltage Distribution And Grid Automation
-
We lead the way when it comes to safe, energy-efficient, and highly available power distribution solutions for low and medium-voltage electrical installations.
-
Product
AC / DC Sensors For High Voltage Measurements
-
The Mors Smitt CatEnergy sensor range provide a proven, reliable, accurate and cost-effective solution for rolling stock. Based on its capacity of multi-voltage and current measurements, alone Mors Smitt sensor products could be used as single solution for all function requiring high voltage measurement on existing and new build train.
-
Product
High Voltage Power Source
PM2000
-
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
Product
VNA Calibration Kits
-
Standard calibration kits used for manual network analyzer calibration
-
Product
Apex Series Calibration Kit
-
The APEX Series Calibration Kit provides calibration personnel the ability to re-certify the calibration of the APEX SL or APEX PRO control systems in-house. A simple Windows based program and an RS232 digital interface to a Keithley multi-meter, goes through system checks and verifications, and provides a detailed printed report of pass/fail, actual and expected values, and tolerances for each parameter checked.
-
Product
High Voltage Safe Measurement Systems
-
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
Product
Zero Gas Generator - Calibration of Ambient Air Monitoring Systems
ZNV-7
-
HORIBA Europe’s Zero Gas Generator ZNV-7 has been developed to check the zero point and dilute the span gas sources in order to carry out the calibration of ambient air monitoring systems. The increasing sensitivity of ambient air analyzers is required by strict official guidelines, which demands pure and dry air in a sufficient quantity at constant pressure.
-
Product
120-600V Solenoid Voltage Tester
1866
-
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC and DC polarity.
-
Product
Dual-Range High Voltage Non-Contact Tester
HVNCVT-1
-
Use to check for the presence of voltage in overhead conductors or find faults in cables.LOW range for 50V AC to 1.5kV AC.HIGH range for 1.5kV AC to 132kV AC.Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case.
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
-
-
Product
Temperature Calibration
-
Process Instruments maintains primary temperature standards for the calibration of Standard Platinum Resistance Thermometers. SPRT''s are measured against a Thomas-type Ten Ohm Standard Resistor (a Leeds & Northrup 4211-B), using a Measurements International automated bridge. Primary thermometry points are maintained at the Water, Tin, Zinc and Gallium points.
-
Product
Calibration Kit
WR-15
-
This precision calibration kit contains a flush short, offset piece and broadband load which allows for a full 12-term port calibration.
-
Product
LXI High Voltage Switching Multiplexer
65-231-914-HI
Multiplexer Module
The 65-231-914-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
-
Product
High Voltage Divider
-
High voltage measuring divider in capacitive or resistive construction.
-
Product
Calibration Lead - Precision Resistor Modules
40-975-037-02-1m
Cable Assembly
The cable assembly is specifically designed to connect to the 37-Pin D-Type calibration port located on the front panel of Pickering Interfaces Precision Programmable Resistor Modules 40-293 and 50-293 enabling calibration via an external DMM.
-
Product
RF Calibration Kit
SMK-3000
-
The SMK calibration kits are precision, high power calibration standards that are used to calibrate RF radios, wattmeters, directional couplers and other high-power RF test equipment in the field or metrology lab. Unlike other calibration solutions, the SMK-3000 calibration kits reduce the cost of ownership and provide a much faster time-to-calibration with lab precision and accuracy you’ve come to expect from Bird.
-
Product
Multiport Calibration Assistant
S95552B
-
The S95552B software application flexibly creates and manages calibration sets for multiport measurements. This software enables you to combine multiple calibration sets with independent test ports as one calibration set with a greater number of test ports. The software also offers a way to re-calibrate using a certain set of test ports to refresh the calibration set.
-
Product
PXI 6x4 High Voltage Power Matrix
40-332-002
Matrix Switch Module
Designed for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. This range is available in 12x2 or 6x4(shown here)matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Telescopic AC Voltage Detector
-
*Non-contact AC voltage detection*Telescopic length 1.3M*Check AC voltage :** Behind the wardrobe** Inside false ceiling**Under ceiling** Low location or ground floor*No need to bend down while checking*Battery powered : 2 x 1.5V (L736 / LR41 / AG3)*Worldwide patent pending*Originated, designed and developed by MEET
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
-
Product
Contact Voltage Detectors
-
Shanghai Beha Electronics Co., Ltd.
The detector detects a high and extra high voltage in AC lines. An elongate insulation rod permits checking of high voltage circuits at safe distance for voltage.
