Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
10 MHz To 67 GHz LAN Wide Dynamic Range Average Power Sensor
L2057XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Dual Digital Aquisition System For Charge Integration And Pulse Shape Discrimination
DT5790
-
The DT5790 operates upon the DPP-PSD firmware, specially developed for Charge Integration and Pulse Shape Discrimination. DPP-PSD is based on an advanced on line Digital Dual Gate Charge Integration allowing an effective data analysis even at high count rate. It performs input signal baseline calculation, self-triggering and double-gate charge integration with programmable parameters, double integration of both prompt and total charge for Pulse Shape Discrimination and pedestal subtraction for energy calculation.
-
Product
Video Signal Generator
NSPG-4500
-
MSPG-4500 is Video Signal Generator for testing Display device such as TV (3D), Monitor (Displayport), and ETC.
-
Product
Socket Tester
-
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 18GHz SMA
60-802-204
Multiplexer Module
The 60-802-204 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Oscilloscope: 100 MHz, 4 Analog Channels
DSOX2014A
Oscilloscope
100 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
-
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
Product
Analog Output PXI Card
GX1648
Analog Output Module
The GX1648 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1648 offers precision signal sourcing performance and quality at an economical price.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
LXI Microwave Multiplexer, SP6T, 10-Bank, 26.5GHz, 50Ω, SMA
60-800-310
Multiplexer Module
Our 60-800-310 is a 10 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
LXI 144-Channel 1GHz Video Multiplexer
60-721A-006
Multiplexer Module
The 60-721A High Performance Video MUX is designed for the switching of RF signals in 75 Ohm systems at frequencies up to 1GHz. It is ideal for 75 Ohm monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
Product
Reflective Memory Hub
ACC-5595
-
The ACC-5595 is a managed hub designed to operate with our 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-610A-006
Multiplexer Module
The 40-610A-006 is a 4-bank, 16-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
VME Test Extender 3U/220mm Universal
110EXT3122-10xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PXI High Density Multiplexer, 4-Bank, 20-Channel, 1-Pole
40-615A-016
Multiplexer Module
The 40-615A-016 is a 4-bank, 20-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PLC Input Modules
-
The DATEXEL DAT6000 series is a unique device designed to add analog inputs to a digital PLC with a few simple instructions. Downloaded into a standard PLC it is possible to acquire analog signals. The PLC will be able to read a 16 Bit digital input equal to the analog signal. The input, output and power supply are isolated from each other. The DAT6000 can linearize , filter and convert the input signal.The DATEXEL DAT6011 converts two voltages -50 mV to 50 mV, -100 mV to 100 mV, -500 mV to 500 mV or -1000mV to 1000mV or thermocouples K Type, J Type, S type, B type, R type, E type, T type and N type to a digital PLC.
-
Product
32 Channel Multievent Peak Sensing ADC
V785
-
The Model V785 is a 1-unit wide VME 6U module housing 32 Peak Sensing Analog-to-Digital Conversion channels. Each channel is able to detect and convert the peak value of the positive analog signals (with >50 ns risetime) fed to the relevant connectors. Input voltage range is 0 ÷ 4 V.
-
Product
Water Meters
-
Hong Kong Songyang Industrial Ltd.
Copper sealed register, the reading can be kept clear in longtime service. The most frost protected metal housing center sweep hand dial. Measuring units: U.S.GALLON, CUBIC FEET and M3. Measuring accuracy conform to American Standard AWWA C-708. Selected high quality Reed-Type pulse. Reliable signal output, long working life
-
Product
8-bit Digitizers
ADC6000
-
Guzik AXIe ADC 6000 Series Digital Acquisition and Processing Modules combine high-speed waveform digitizer with built-in digital signal processing hardware, which enables mixed-domain signal capture and analysis with high-speed data transfer link to a computer. The ADC 6000 Modules come in a space-saving display-less 1U 19” AXIe modular form factor.
-
Product
PXI I/O Board
MZ-TrigIO
Digital I/O
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 4-Bank 18GHz SMA
60-801-204
Multiplexer Module
The 60-801-204 is a 6-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP021-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
Data Acquisition Devices
-
Our data acquisition and encoding systems provide significant performance in reception, signal conditioning and encoding of all types of signals while used in missiles, airborne vehicles, mobile ground-based testing and other platforms that require ease of operation, flexibility, ruggedization and small packaging.
-
Product
With SAT-IF input EDFA
HA4600/IF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
Product
Digital Telemetry Solutions
-
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
Product
LXI 2.4GHz 50ohm 32x4 Matrix
60-772-001
Matrix Switch Module
The 60-772 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 4 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
Monitoring Receiver
-
The portable monitoring receivers and remotely controllable analyzers were especially developed for signal search, radio detection, spectrum monitoring and frequency management.
