Portable Data Acquisition
-
Product
Data Acquisition
-
Data Acquisition (DAQ) converts temperature, pressure, current and other measurements into numeric values for computers and controllers to process. We offer Analog and Digital Data Acquisition hardware communicable over Modbus RTU, Modbus TCP, Ethernet/IP, EtherCAT, BACnet, Profibus, CANopen, DeviceNet and FRnet protocols. We offer Free EZ Data Logger Control, Monitoring and Data Logging Software.
-
Product
Data Acquisition Equipment
-
Get the data you want, where, how and when you want it. Fluke gives you a broad choice in data acquisition for process monitoring and laboratory test systems. You can choose a stationary or portable data logger. Transfer data to internal memory, to a removable memory card, or to your PC. Choose a standalone or distributed networked units. And you can expand your system from 20 to 1,000+ channels, depending on the series.
-
Product
PXI Data Acquisition
DAQ
Data Acquisition Module
Installation and configuration is fast and easy with standard connectors, soft front panels and Keysight connection expert. In addition, software drivers support the most common programming environments such as Visual Studio®, C, C++, Visual Basic, MATLAB® and LabVIEW™.
-
Product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784191-01
Data Storage
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
-
Product
PCI Data Acquisition
-
PCI data acquisition product line provides 50MS/s, 500MS/s, 1GS/s and other high-speed digital conversion cards. These conversion cards feature 8- and 12-bit resolution, as well as wide bandwidth and large acquisition memory. The product line also includes PCI digitizers with on-board signal processing capabilities, and streaming firmware using the serial FPDP protocol to capture and transmit all acquired data without stalling or loss.
-
Product
Data Acquisition Systems
-
Diversified Technical Systems, Inc.
DTS offers a full line of high performance data acquisition systems, sensors, accessories and software to meet a wide range of critical test requirements. Let the DTS team of experienced engineers and test professionals help you find the right instrumentation for your application.
-
Product
4-Slot Distributed DA&C System For Ethernet
ADAM-5000L/TCP
Data Acquisition Module
10/100Base-T auto-negotiation high-speed communication portSupports Modbus/TCP for easy integrationSupports UDP event handling function1500 VDC isolation for Ethernet communicationProvides C and .NET class library to develop applicationsBuilt-in watchdog timer for system auto-resetWindows utility- I/O modules configuration and calibration- Network auto searching- Data stream setting- Current status monitoring and alarm trigger4 I/O slots for up to 64 points data monitoring and controlAllows concurrent access for 8 host PCsAllows remote configuration via EthernetUp to 100 m communication distance w/o repeaterARM 32-bit RISC CPU
-
Product
Data Acquisition Card
-
The Elsys DAQ / data acquisition cards are high precision and high resolution digitizers with complex trigger capabilities, a continuous data acquisition mode, differential or single-ended inputs, digital marker inputs as well as an optional integrated ICP/IEPE supply for piezo sensors.
-
Product
Pico Data Logger / Data Acquisition Range
-
Pico data acquisition products provide a straightforward answer to your data logging needs.Our data loggers require no power supply and simply plug into a USB port on your PC, or an Ethernet port on your PC or network.Every logger is supplied with PicoLog data acquisition software so you can measure, record and analyze your data.
-
Product
Systems And Data Acquisition
-
From sensor to software: Kistler offers complete systems for selected applications.
-
Product
Multi-Channel Data Acquisition System
PI-3105
-
This highly flexible system is designed to test a wide variety of imaging devices, from low-noise astronomy and medical devices, to military and machine-vision devices with GB/sec data rates.
-
-
Product
PCI Data Acquisition Boards
AD8CH12B-100DMA Series - Single low-spur 8-bit, 100 MS/s
-
Model AD8CH12-100DMA has eight simultaneous-sampling 12-bit A/D converters, and can continuously acquire and transfer hundreds of megabytes or even gigabytes of A/D data directly into host system memory at up to 100 MB/s, via 64 or 32 bit PCIbus DMA. It can acquire and transfer eight 8-bit A/D channels at up to 12.5 MSPS each (100MB/sec aggregate), or eight 12-bit A/D channels at up to 6.25 MSPS each, or four 8-bit channels at up to 25 MSPS each, or four 12-bit channels at up to 12.5 MSPS each.
-
Product
Data Acquisition Recorders & Loggers
DAS1800
-
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
Product
Data Acquisition
-
Apogee Labs offers a variety of modular chassis types used for the gathering of various data and video sources for use in data transport and recording applications.
-
Product
Remote Data Acquisition
-
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
Product
Data Acquisition
-
Data acquisition involves sampling signals that measure real-world data and converting this data into digital numeric values. As easy as this may sound, it is a lot harder to create a fully integrated, high-performing, and maximum flexible platform. We are proud to present our solutions based on cutting-edge engineering.
-
Product
Network-Ready Data Acquisition System
DAPserver 500
-
The DAPserver 500 and DAPserver 502 – and the DAPserver 500R and 502R, the latter "R" models for rugged environments – serve as fully integrated test, measurement, and control products. Built with experience gained over many years of integrating third-party hardware, these high-performance combined systems are now available as standard products,
-
Product
PCI Data Acquisition Boards
AD8-650X2DMA Series - 8 bit, 800MS/s
-
Model AD8-650X2DMA is similar to the AD8-1250DMA, but contains two simultaneous-sampling A/D channels, each capable of sampling at up to 800 MS/s.
-
Product
I-8000 Parallel Data Acquisition Modules
-
ICP DAS I-8000 Parallel Series I/O are high speed cartridge based and come in a multitude of digital and analog configurations. They are communicable via an RS-485 backplane in all of ICP DAS USA's I-8000 & I-87K series rack mount controllers. There are two types of I/O communication bus, parallel bus and serial bus. The parallel bus type I/O modules (high profile I-8K series) are high speed, used only in the PACs including XPAC, WinPAC, iPAC, ViewPAC, etc. And the serial bus type I/O modules (high profile I-87K series) are low speed, used in both PACs including XPAC, WinPAC, iPAC, ViewPAC, etc.
-
Product
Data Acquisition And Control System
DynPro2
-
Demands for data acquisition call for a range of complex requirements that need to come together to meet customer challenges, industry advancements and safety. DynPro2 is a full-featured, testing and measurement system that’s capable of testing a wide variety of equipment including engine, vehicle and industrial component testing.
-
Product
Data Acquisition and Analysis Software
-
Matec Instrument Companies, Inc.
Matec provides a full suite of Microsoft Windows pc-based data acquisition and analysis software for your ultrasonic testing applications. In addition to our base software packages, our team of software engineers can work with you to develop customized scan forms and algorithms specific to your application demands.
-
Product
Titan Data Acquisition
DAQ
-
Titan Data Acquisition (DAQ) Systems offer universal signal conditioning, low power consumption, convenient SD card storage, and easy-to-use software. Systems can be purchased as a complete test kit, including custom cables and accessories. Titan products are designed and built in the US.
-
Product
PCI Data Acquisition Boards
AD14-100DMA Series - Dual 14-bit A/D, 25 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
Data Acquisition System
DataNet
-
High-end 16-bit intelligent data acquisition system, utilizing ZigBee wireless telemetry protocol, with 4 inputs for direct measurement.
-
Product
Data Acquisition Control Boards
X-GCU
-
X-GCUs are a data acquisition and control boards of Detection Technology’s digital X-ray detector platforms. X-GCU together with the digital X-Cards provide complete and easily scalable detector subsystems shortening time-to-market and delivering total cost savings for all types of X-ray imaging systems.
-
Product
Data Acquisition Software
-
The very powerful data acquisition software from Elsys transforms the data acquisition hardware into a measurement solution that can be used directly after little training.
-
Product
BACnet Data Acquisition
-
BACnet is a communication protocol for building automation and control networks. BACnet is designed to allow communication for applications such as heating, ventilating, and air-conditioning control, lighting control, access control, and fire detection systems and their associated equipment. The BACnet protocol defines a number of services that are used to communicate between building devices. Itl also defines a number of objects that are acted upon by the services. The objects include Analog Input, Analog Output, Analog Value, Binary Input, Binary Output, Binary Value, Multi-State Input, Multi-State Output, and Device, etc.
-
Product
Modbus TCP Data Acquisition
-
Modbus TCP based Data Acquisition Modules in a analog and digital I/O configurations including current, voltage, thermistor, thermocouple, RTD, and strain gauge. Some are powered over Ethernet, some have two Ethernet ports and some can send email alarms and trigger outputs based on inputs.
-
Product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784192-01
Data Storage
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
