Humidity Chambers
Controlled analysis of a product exposed to humid conditions.
See Also: Environmental Chambers, Chambers, Temperature Chambers
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
High & Low Temperature Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
Combined Temperature and Altitude Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Altitude & Temperature Test Chamber combine Altitude and temperature to test various components and products, especially the aircraft avionics. Automatic controlled vacuum system provide a precise altitude simulated condition up to 30000 meters. Available to connect cable for the electronic performance test.
-
Product
Environmental Test Chambers
-
Angelantoni Test Technologies Srl
We supply a wide range of climatic chambers capable of reproducing a very large number of simulated environmental conditions, which can be combined in some cases. Select the type of test and the area of application and you will find the right solution for your needs!
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Ozone Aging Test Chamber
-
This product series are mainly used to evaluate the ozone aging resisting performance of rubber and the protective efficacy of the antiozonant so as to take the effective ozone-aging resisting measures to extend the life span of the rubber products.
-
Product
Rain Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Rain test chambers are environmental test machines to simulate the different degrees of rainy and soaking circumstances to assess the waterproof performance of consumer electronic products, electronic components, outdoor lights, automobile parts etc. Rain test instruments consist of many different chambers like IPX1/2 rain test chamber, IPX3/4 rain test chamber, IPX5/6 test chamber, IPX 7/8/9K testing equipment to suit different testing requirements, becoming the most frequently used testing instruments in electronics and lighting industries.
-
Product
Xenon Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Designed to be accelerate the weathering and aging process by simulating exposure to sunlight.
-
Product
Stability Testing Chamber - Double Door Model
Q20
-
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c and corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
Product
Temperature and Humidity Regulator
H3061-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Temperature, Humidity, CO2 Transmitter
H6020
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
IPX7 Water Ingress Protection Immersion Test Chamber
CX-IPX7
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX7 Water Ingress Protection Immersion Test ChamberThe main function of the immersion test equipment is for the electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts and other products in the simulated rain conditions, the physical and other related properties of the test.
-
Product
Temperature Cycling Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature Cycling test chamber is performed on materials to determine the resistance of exposure to alternating extremes of high and low temperatures.
-
Product
Enlarge Environmental Chamber
REXMED REC-250
-
MOD. REC-250, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Extremely Accelerated Stress Test Chambers
-
The extremely accelerated stress environment is defined by high temperature, high humidity and high pressure. WEIBER provides humidity resistance evaluation test for electronics components through customized Extremely Accelerated Stress Test Chamber. This chamber provides high performance test in minimal amount of time according to international IEC 60068-2-66 standard. This chamber also known as Accelerated Stress Test Chamber, Halt and Hass Test Chamber, Halt Test Chamber and Hass Test Chamber.This chamber reduces the time taken for humidity testing in electronic components. 2 types of tests saturated and unsaturated extremely accelerated stress test can be performed. In saturated test the temperature is maintained at 1210C at 100%RH, and for unsaturated temperature of 110, 120, 1300C is maintained at 85%RH. Normally for electronic components unsaturated type test is done.
-
Product
Sensor Technology for Measuring Heat Flux, Humidity, and Temperature
Uval gt Building
-
uvalgt Building calculates the physical values that matter for buildings, such as heat flux (U-value), humidity and temperature. The measurement kit provides construction professionals with solid data during damage investigations, final inspections of construction work and renovation planning.
-
Product
IP X1, X2 Chamber - Drip/IP Test Chamber
-
The drip box testing chambers from Weiber are rain test machines used for testing the outer protection of signal devices, external lighting equipments and car lamps etc. The equipment finds widespread usage in electronics industry and automotive and aerospace industries and is commonly employed for quality testing of products. The test chamber comprises of the guiding upright column, a drip mold, a rotating sample table with adjustable speed and a level meter to allow observation of the level in the drip mold. The equipment uses high quality construction materials for a sturdy construction and is designed for safe and reliable operation. The guiding upright column is made up of high-quality, plastic coated square steel pipe, whereas the drip mold is made up of high-quality stainless steel finish plate undergoing knurling.
-
Product
Temperature and Humidity Bar Type Transmitter
T3417
-
Relative humidity, temperature sensors at 700mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Hand-held meter for humidity / temperature
OMNIPORT 30OMNIPORT 30
-
The state of the art hand-held for precise measurement of various physical quantities, such as, humidity, temperature, dew point, air velocity, volumetric flow, air pressure. The numerous probes all incorporate high quality sensors developed by E+E and offer a total of 22 measurands.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Accredited Humidity Calibration Services
-
Thunder Scientific's calibration laboratory is accredited by NVLAP (National Voluntary Laboratory Accreditation Program), Certificate of Accreditation No. 200582-0 to ISO/IEC 17025 and ANSI/NCSL Z540-1 1994.
-
Product
Relative Humidity Outdoor, Indoor Probe
T1110
-
Only relative humidity output 4-20mA.Also available with direct temperature RTD Pt1000 sensor output.Other sensors on request.
-
Product
Cyclic Corrosion Test Chambers
CCT
-
Cyclic Corrosion Test Chambers are used throughout the automotive, aerospace, fasteners, electronics, paints and coating industries.
-
Product
Temperature & Humidity Meters
-
Electronic temperature and humidity sensors measure the rise in the 1990s the industry in recent yesrs, domestic and foreign research and development in the humidity sensor made considerable progress. This product uses the highest quality imported digital sensor, stable performance, strong consistency.
-
Product
Humidity transmitters for HVAC
-
Humidity transmitter for heating, ventilation and air conditioning technology. Humidity transmitters for building technology are also available as OEM versions in custom designs.
-
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7310
-
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
HALT HASS & AGREE Vibration Test Chambers
-
Weiss Technik series of HALT & HASS and AGREE Vibration test chambers provide combined testing for temperature, humidity and vibration for your testing applications.
-
Product
Vibration Test Chamber
Series TV / CV
-
During transportation, or when used under heavy mechanical loads your products vibrations or oscillations can be exposed, which may negatively affect the quality and longevity. To simulate these effects can be personalized with the modular standardized versions of the corresponding CTS installations, the requirements such as vertical and horizontal meet vibration and this in conjunction with very high rates of temperature change.
