-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
Test Fixture
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
68-Pin VHCDI Male to 68-Pin VHCDI Male Shielded Cable
190233-0R5
Multifunction Cable
The SHC68-C68-EPM is compatible with many NI data acquisition devices. The SHC68-C68-EPM is intended for custom breakout fixtures that use the VHDCI 0.8 mm connector.
-
Product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
Test Platform
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
Product
Small Footprint Flex 20 ATE
Flex 20
-
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
-
Product
Receiver, G12, 12 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310104334
Receiver
The 20” G12 Receiver is a slide-mounted receiver. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-721
Matrix Switch Module
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
CMP Mechanical Kits (230x135mm)
230199 – CMP-240-HP
-
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
Product
RF Shielded Fixture
-
A semi-automatic, pneumatically operated fixture with a sliding pressure top provides a very short mechanical cycle-time. The unit is prepared for full, multi-station automatic operation using a centrally placed robot arm for UUT load/unload.
-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
Test Port Cable
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
G18 - 18 Module Solution
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. Ordering has been simplified by offering a package that includes the G18 receiver, receiver mounting plate, flanges and instrument bracket. Slides are rated to support 180 lbs (81 kg) to accommodate large fixtures. To determine the slide kit needed, measure rack depth between mounting rails. With this measurement, choose the slide mounting kit that fits the rack.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 585 x 250 mm (wxd)
CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
PC Based Test Setup for LED PCB of Luminaire
-
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
Product
Clamshell Type Mechanical Fixtures
Series 71
-
The VP Series 71 dual well mechanical kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface and the advantage of testing two devices. This can be similar devices, or devices that are used together in a functional test. The VP Series 71 Kits have the same available features and options as the Series 70 Kit and are available with or without the ITA G12 Interface.
-
Product
Stand-Alone Test Fixture
MA 2011/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1000Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,00 kg
-
Product
IR LightSource
-
Universal LightSources emit Infrared (IR) radiant energy and are designed for the testing of IR(infrared) sensors used in remotely-controlled products.The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
-
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
Product
Drop-In In-Circuit Test Fixtures
The Chameleon
-
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Product
DisplayPort™
-
SCHILLER AUTOMATION GmbH & Co. KG
Wilder Technologies Enhanced DisplayPort™ and miniDisplayPort™ test adapters enable Host and Device testing to DP2.1 Specifications. Supporting increasing data rates (UHBR10, UHBR13.5 and UHBR20) to drive 8k displays and higher refresh rates, Wilder’s fixtures provides the a platform for pre-compliance and compliance testing.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
DC Power Module, 35V, 1.5A, 50W
N6734B
Power Module
The Keysight N6734B is a 52.5 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
In‐Circuit Test Fixtures
-
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
