-
Product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
SCSI Female Terminator
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
-
LampChek indicates the lamp and fixture continuity.
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
EIS Battery Analyzer
BA8100
-
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
Product
PCIe
M.2 Gen4 Socket2
-
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 2 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 2 Source and Sink devices.
-
Product
Environmental Chambers
3119-600 Series
-
The Instron environmental chambers are precision thermal enclosures designed to integrate with static or dynamic test systems, enabling evaluation of material behavior under controlled non-ambient conditions. They circulate hot or cold air over specimens and grips using forced-convection to maintain stable temperatures. These chambers are available in a variety of standard sizes (or can be customized), and are compatible with extensometers, grips, and fixtures to provide a turnkey solution for temperature-dependent testing from subzero to elevated conditions.
-
Product
Specialized Component IB-R-SB-040-4A-WW-03-FL
1170327
-
The IB-R-SB-040-4A-WW-03-FL is a specialized component designed by Interface Solutions, ideal for ICT fixtures. This product excels in its ability to function effectively in extreme temperature ranges from -45°C to +100°C, making it suitable for various industrial and technical environments. The assembly is crafted with precision, integrating a reliable design aimed at providing optimal performance under demanding conditions.
-
Product
Fiber End-face Interferometer
-
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
-
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
Emergency Battery Power Supply Test Fixture
TA-61
-
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
Product
In‐Circuit Test Fixtures
-
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
Product
Flying Probe Tester
Condor MTS 505
-
Primarily the Flying Probe Tester was developed to enable In-Circuit testing (ICT) of prototype PCBs. For testing a new design an existing fixture has to be changed or a new fixture has to be procured. The fixtureless design of the MTS 505 Condor is one of its most attractive properties, where the unnecessary and costly time delays incurred for fixture build or changes can be avoided. It is the ideal platform for testing prototypes.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
PC Based Test Setup for LED Driver of LED
-
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
Product
Prototype Engineering Test
PET-2/PET-3
-
Exatron's Prototype Engineering Test (PET) Fixture is a semi-automated solution that bridges the gap between a fully automated handling system and a low cost, lower volume handler.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Product
Edge Connector Fixture
220EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
Product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
-
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
IB-F-SB-085-4A-WW-05-FL
1170306
-
The IB-F-SB-085-4A-WW-05-FL from Interface Solutions is a specialized module designed for ICT fixtures, ensuring reliable and efficient performance in demanding environments. This model, identified by the order code 1170306, provides robust electrical specifications with a continuous current rating of 4.00 A, making it suitable for applications requiring consistent power delivery. With meticulous engineering, this block exhibits a total length of 60.00 mm and projection height of only 1.14 mm, ensuring a compact form-factor that can easily fit into tight spaces without compromising on functionality.
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
10-CH Pneumatics CAN
YAV90PNE
CAN Interface
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
